Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent
-
Displacement
567.5 in³
763 in³
-
Stroke
5.9 in
6.2 in
-
Number of Cylinders
6
6
-
Torque Rise - ISO 9294
44%
-
-
Base Power (1st Gear) - Net
-
238 HP
-
Speed at Rated Power
-
1,850 rpm
-
Note (3)
-
Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator.
-
Note (2)
-
Optimized VHP Plus is standard for the 14M3.
-
Torque Rise
-
41%
-
Maximum Altitude - Full Power
-
13900 ft
-
Maximum Torque - VHP Plus
-
1137 lb/ft
-
Maximum Altitude - Full Power (Tier 3)
-
14349 ft
-
Maximum Altitude - Full Power (Tier 2)
-
12049 ft
-
Note (1)
-
Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture.
-
Standard - Fan Speed - Minimum
-
550 rpm
-
Note (4)
-
Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp)
-
Note (5)
-
Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
-
Standard - Fan Speed - Maximum
-
1,600 rpm
-
Weights
Operating Weight - Typically Equipped
20236 lb
57250 lb
-
Gross Vehicle Weight - Base* - Total
-
50980 lb
-
Gross Vehicle Weight - Base* - Front Axle
-
13994 lb
-
Gross Vehicle Weight - Typically Equipped - Total
-
57250 lb
-
Gross Vehicle Weight - Typically Equipped - Rear Axle
-
42005 lb
-
Gross Vehicle Weight - Typically Equipped - Front Axle
-
15245 lb
-
Gross Vehicle Weight - Base* - Rear Axle
-
36994 lb
-
Note
-
*Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab.
-
Moldboard
Blade Width
12 ft
14 ft
-
Cutting Edge
6 in
-
-
Arc Radius
16.3 in
16.3 in
-
Throat Clearance
6.5 in
4.6 in
-
End Bit
6 in
-
-
Blade Width - With End Bits
-
169 in
-
Blade Height - With Cutting Edge
-
24.9 in
-
Blade Width - Without End Bits
-
164 in
-
Blade Height - Without Cutting Edge
-
23 in
-
Dimensions
Basic Blade Width
140 in
-
-
Length of Machine*
397.6 in
-
-
Width
97.6 in
-
-
Note
*Typically equipped with push block and ripper.
-
-
Maximum Height
132 in
-
-
Service Refill
Hydraulic System
14.5 gal (US)
-
-
Engine Crankcase
7.9 gal (US)
-
-
Circle Drive
1.8 gal (US)
-
-
Fuel Tank
100 gal (US)
-
-
Front Wheel Spindle Bearing - Each
0.13 gal (US)
-
-
Machine Weight
Note
*Typically equipped with push block and ripper.
-
-
All-Wheel Drive (AWD) Weight
44613 lb
-
-
Weight*
42325 lb
-
-
Blade Range
Maximum Lift Above Ground
18.9 in
16.5 in
-
Maximum Depth of Cut
28.9 in
23.3 in
-
Circle Centershift - Left
-
25.6 in
-
Circle Centershift - Right
-
20.5 in
-
Blade Tip Range - Backward
-
5°
-
Maximum Shoulder Reach Outside of Tires - Right
-
78.9 in
-
Moldboard Sideshift - Right
-
31.1 in
-
Moldboard Sideshift - Left
-
29.1 in
-
Maximum Shoulder Reach Outside of Tires - Left
-
73.6 in
-
Blade Tip Range - Forward
-
40°
-
Frame
Circle - Outer Diameter
-
71.7 in
-
Front Axle - Wheel Lean - Left/Right
-
17.1°
-
Front Axle - Total Oscillation per Side
-
32°
-
Service Refill Capacities
Transmission and Differential
-
23.5 gal (US)
-
Diesel Exhaust Fluid Tank (Tier 4 Only)
-
5.8 gal (US)
-
Hydraulic System
-
33 gal (US)
-
Circle Drive
-
1.8 gal (US)
-
Cooling System
-
15.9 gal (US)
-
Fuel Tank
-
109.9 gal (US)
-
Air Conditioning System
Air Conditioning
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton).
