|
|
|
|
Engine |
| Net Power - EEC 80/1269 |
250 HP |
- |
535 HP |
| Net Power - ISO 9249/SAE J1349 |
250 HP |
- |
- |
| Standard Capability |
109 °F |
122 °F |
122 °F |
| Engine RPM |
2,000 |
- |
- |
| Engine Model |
Cat C9.3 |
Cat C13 |
Cat C27 |
| Bore |
4.5 in |
5.1 in |
5.4 in |
| Emissions |
U.S. EPA Tier 4 Final/EU Stage V |
Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent |
Tier 4 Final/Stage IV or Equivalent to Tier 2/Stage II |
| Displacement |
567.5 in³ |
763 in³ |
1648 in³ |
| Stroke |
5.9 in |
6.2 in |
6 in |
| Number of Cylinders |
6 |
6 |
12 |
| Torque Rise - ISO 9294 |
44% |
- |
- |
| Base Power (1st Gear) - Net |
- |
238 HP |
- |
| Speed at Rated Power |
- |
1,850 rpm |
- |
| Note (3) |
- |
Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. |
Net power advertised is the power available at rated speed of 1,800 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. |
| Note (2) |
- |
Optimized VHP Plus is standard for the 14M3. |
Optimized VHP Plus is standard for the 24. |
| Torque Rise |
- |
41% |
- |
| Maximum Altitude - Full Power |
- |
13900 ft |
- |
| Maximum Torque - VHP Plus |
- |
1137 lb/ft |
- |
| Maximum Altitude - Full Power (Tier 3) |
- |
14349 ft |
- |
| Maximum Altitude - Full Power (Tier 2) |
- |
12049 ft |
- |
| Note (1) |
- |
Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. |
Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. |
| Standard - Fan Speed - Minimum |
- |
550 rpm |
- |
| Note (4) |
- |
Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp) |
Power as declared per ISO 14396. Rated rpm 1,800 (561 hp) |
| Note (5) |
- |
Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
- |
| Standard - Fan Speed - Maximum |
- |
1,600 rpm |
- |
Weights |
| Operating Weight - Typically Equipped |
20236 lb |
57250 lb |
165314 lb |
| Gross Vehicle Weight - Base* - Total |
- |
50980 lb |
- |
| Gross Vehicle Weight - Base* - Front Axle |
- |
13994 lb |
- |
| Gross Vehicle Weight - Typically Equipped - Total |
- |
57250 lb |
- |
| Gross Vehicle Weight - Typically Equipped - Rear Axle |
- |
42005 lb |
- |
| Gross Vehicle Weight - Typically Equipped - Front Axle |
- |
15245 lb |
- |
| Gross Vehicle Weight - Base* - Rear Axle |
- |
36994 lb |
- |
| Note |
- |
*Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab. |
- |
Moldboard |
| Blade Width |
12 ft |
14 ft |
24 ft |
| Cutting Edge |
6 in |
- |
- |
| Arc Radius |
16.3 in |
16.3 in |
- |
| Throat Clearance |
6.5 in |
4.6 in |
- |
| End Bit |
6 in |
- |
- |
| Blade Width - With End Bits |
- |
169 in |
- |
| Blade Height - With Cutting Edge |
- |
24.9 in |
- |
| Blade Width - Without End Bits |
- |
164 in |
- |
| Blade Height - Without Cutting Edge |
- |
23 in |
- |
| Blade Height |
- |
- |
40 in |
Dimensions |
| Basic Blade Width |
140 in |
- |
- |
| Length of Machine* |
397.6 in |
- |
- |
| Width |
97.6 in |
- |
- |
| Note |
*Typically equipped with push block and ripper. |
- |
- |
| Maximum Height |
132 in |
- |
- |
Service Refill |
| Hydraulic System |
14.5 gal (US) |
- |
- |
| Engine Crankcase |
7.9 gal (US) |
- |
- |
| Circle Drive |
1.8 gal (US) |
- |
- |
| Fuel Tank |
100 gal (US) |
- |
- |
| Front Wheel Spindle Bearing - Each |
0.13 gal (US) |
- |
- |
Machine Weight |
| Note |
*Typically equipped with push block and ripper. |
- |
- |
| All-Wheel Drive (AWD) Weight |
44613 lb |
- |
- |
| Weight* |
42325 lb |
- |
161695 lb |
Blade Range |
| Maximum Lift Above Ground |
18.9 in |
16.5 in |
16.1 in |
| Maximum Depth of Cut |
28.9 in |
23.3 in |
21.7 in |
| Circle Centershift - Left |
- |
25.6 in |
- |
| Circle Centershift - Right |
- |
20.5 in |
- |
| Blade Tip Range - Backward |
- |
5° |
- |
| Maximum Shoulder Reach Outside of Tires - Right |
- |
78.9 in |
- |
| Moldboard Sideshift - Right |
- |
31.1 in |
- |
| Moldboard Sideshift - Left |
- |
29.1 in |
- |
| Maximum Shoulder Reach Outside of Tires - Left |
- |
73.6 in |
- |
| Blade Tip Range - Forward |
- |
40° |
- |
Frame |
| Circle - Outer Diameter |
- |
71.7 in |
- |
| Front Axle - Wheel Lean - Left/Right |
- |
17.1° |
- |
| Front Axle - Total Oscillation per Side |
- |
32° |
- |
Service Refill Capacities |
| Transmission and Differential |
- |
23.5 gal (US) |
- |
| Diesel Exhaust Fluid Tank (Tier 4 Only) |
- |
5.8 gal (US) |
- |
| Hydraulic System |
- |
33 gal (US) |
- |
| Circle Drive |
- |
1.8 gal (US) |
- |
| Cooling System |
- |
15.9 gal (US) |
- |
| Fuel Tank |
- |
109.9 gal (US) |
- |
Air Conditioning System |
| Air Conditioning |
- |
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton). |
- |
