Compare Equipment Go Back
 6040 Hydraulic Mining Shovel |
 6060 Hydraulic Mining Shovel |
 6020B Hydraulic Shovel |
|
General |
|||
|---|---|---|---|
| Engine Output - SAE J1995 | 2079 HP | 3015 HP | 1040 HP |
| Bucket Payload | 43.7 ton (US) | 67 ton (US) | 23.8 ton (US) |
| Operating Weight | 446 ton (US) | 660 ton (US) | 253.8 ton (US) |
| Note | Specifications above apply to the HRC Face Shovel configuration. Backhoe and Frontless configurations are also available for both HRC and LRC. | Specifications shown above apply to Face Shovel configuration. Backhoe and Frontless configurations are also available. | Specifications shown above apply to a Backhoe configuration. A frontless configuration is also available. |
| Standard Bucket Capacity | - | - | 15.7 yd³ |
Engine |
|||
| Engine Model | 2 x Cat C32 | 2 x Cat 3512E | - |
| Gross Power - SAE J1995 | 2079 HP | - | - |
| Net Power - SAE J1349 | 1915 HP | - | - |
| Note | Power output relates to highly regulated engines. Lesser regulated engines are also available. | - | - |
Diesel Engines |
|||
| Number of Cylinders - Each Engine | 12 | 12 | - |
| Bore | 5.71 in | 6.69 in | - |
| Stroke | 6.38 in | 8.46 in | - |
| Displacement | 1959 in³ | 3574 in³ | - |
| Aspiration | Turbocharged and air-to-air aftercooled | Turbocharged and charge air-cooled | - |
| Components (1) | Additional high-capacity water separator | Non-DEF Aftertreatment system with Diesel Oxidation Catalysts (DOCs) | - |
| Components (2) | Two-stage fuel filter including water separator | High-capacity water separator | - |
| Components (3) | Heavy-duty air filters | Two-stage fuel filter with series filtration | - |
| Components (4) | Microprocessed engine management | Heavy-duty air filters | - |
| Components (5) | Hydraulically driven radiator fan with electronically controlled fan speed | Microprocessed engine management | - |
| Fuel Tank Capacity | 2098 gal (US) | - | - |
| Emissions | Meets U.S. EPA Tier 4 Final and EU Stage V emission standards | - | - |
| Rated Speed | - | 1,800 min-1 (1,800 rpm) | - |
| Components (6) | - | Hydraulically driven radiator fan with electronically controlled fan speed | - |
| Components (7) | - | Exhaust manifold and turbo heat shields | - |
Electrical System - Diesel Drive |
|||
| System Voltage | 24V | - | - |
| Batteries in Series/Parallel Installation | 6 x 210 Ah - 12 V each; 630 Ah - 24 V in total | - | - |
| Components (1) | 6 maintenance-free batteries | - | - |
| Components (2) | Battery isolation relays and switches | - | - |
| Components (3) | Emergency stop switches accessible from ground level, in engine module and in operator's cab | - | - |
| Components (4) | 14 LED high-brightness working flood lights | - | - |
| Components (5) | 11 LED high-brightness service lights | - | - |
Operating Weights |
|||
| 6040 FS - Standard Track Pads | 3.9 ft | - | - |
| 6040 FS - Operating Weight | 891980 lb | - | - |
| 6040 FS - Ground Pressure | 24.1 N/cm2 (35.0 psi) | - | - |
| 6040 - Standard Track Pads | 3.9 ft | - | - |
| 6040 - Operating Weight | 897930 lb | - | - |
| 6040 - Ground Pressure | 24.3 N/cm2 (35.3 psi) | - | - |
| Note | 1600 mm track pads available as option | Operating weights include: base machine, front attachment, standard track pads, standard rock bucket, 100% fuel and lubricants. | - |
| 6040 FS - Note | Other track pads available on request | - | - |
| 6060 FS - Standard Track Pads | - | 4.58 ft | - |
| 6060 FS - Operating Weight | - | 1320110 lb | - |
| 6060 FS - Ground Pressure | - | 26.6 N/cm2 (38.5 psi) | - |
| Backhoe - Standard Track Pads | - | 4.58 ft | - |
| Backhoe - Operating Weight | - | 1323860 lb | - |
| Backhoe - Ground Pressure | - | 26.7 N/cm2 (38.7 psi) | - |
Hydraulic System with Pump Managing System |
|||
| Hydraulic Tank Capacity - Diesel Version - Approximately | 898 gal (US) | - | - |
| Total Volume of Hydraulic Oil - Diesel Version - Approximately | 1532 gal (US) | - | - |
| Main Pumps - Diesel Version | 4 x variable swash plate pumps | 8 variable swash plate pumps | - |
| Main Pumps - Maximum Oil Flow - Diesel Version | 4 x 724 L/min (4 x 191 gal/min) | 8 x 650 L/min (8 x 172 gal/min) | - |
| Maximum Pressure - Attachment | 4350 psi | 4640 psi | - |
| Maximum Pressure - Travel | 5080 psi | 5220 psi | - |
| Swing Pumps - Diesel Version | 4 x reversible swash plate pump | 4 reversible swash plate pumps | - |
| Swing Pumps - Maximum Oil Flow - Diesel Version | 4 x 321 L/min (4 x 85 gal/min) | 4 x 352 L/min (4 x 93 gal/min) | - |
| Maximum Pressure - Swing Pumps | 5080 psi | 5075 psi | - |
Hydraulic Oil Cooling |
|||
| Diameter - Fan | 2 × 1524 mm (2 × 60 in) | 46 in | 4.92 ft |
| Oil Flow of Cooling Pumps - Diesel Version | 2 x 799 L/min (2 x 211 gal/min) | - | - |
| Features (1) | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running |
| Features (2) | Fan speed is thermostatically controlled | Fan speed and flow of oil to the coolers are thermostatically controlled | Variable electronically controlled flow of oil through cooler and fan speed |
| Features (3) | Extremely high cooling efficiency to ensure optimum oil temperature | Extremely high cooling efficiency to ensure optimum oil temperature | Superior cooling efficiency to ensure optimum oil temperature |
| Components (1) | Gear type cooling pumps supplying high-volume, low-pressure oil to aluminum coolers | - | - |
| Components (2) | Variable axial piston pumps supplying low-volume, high-pressure oil to fans | - | - |
| Oil Flow of Cooling Pumps | - | 4 x 488 L/min (4 x 129 gal/min) | 211 gal/min |
| Components | - | 4 cooling fans | - |
| Features (4) | - | Gear-type cooling pumps supplying high-volume, low-pressure oil to fans and aluminum coolers | - |
Swing System |
|||
| Swing Drive | 3 compact planetary transmissions with axial piston motors | 4 compact planetary transmissions with axial piston motors | 2 compact planetary transmissions with axial piston motors |
| Parking Brake | Wet multiple disc brake, spring-loaded/hydraulically released | - | Wet multiple-disc brake, spring-loaded/hydraulically released |
| Maximum Swing Speed - Diesel Version | 4.7 r/min | - | - |
| Swing Ring | Triple-race roller bearing with sealed internal gearing | Triple-race roller bearing with sealed internal gearing | Triple-race roller bearing with sealed internal gearing |
| Features (1) | Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody | Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody | Open swing circuit with auto slow down when joysticks in neutral |
| Features (2) | Closed-loop swing circuit with torque control | Closed-loop swing circuit with torque control | All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system |
| Features (3) | Hydraulic braking of the swing motion by counteracting control | Hydraulic braking of the swing motion by counteracting control | - |
| Features (4) | All raceways and the internal gearing of swing ring supplied by automatic central lubrication system | All raceways and the internal gearing of swing ring, supplied by automatic central lubrication system | - |
| Parking Brakes | - | Wet multiple disc brake, spring loaded/hydraulically released | - |
| Maximum Swing Speed | - | 3.8 r/min | 4.9 r/min |
Undercarriage |
|||
| Travel Speed - 1st Stage - Maximum | 0.93 mile/h | 0.68 mile/h | 0.68 mile/h |
| Travel Speed - 2nd Stage - Maximum | 1.55 mile/h | 0.99 mile/h | 1.49 mile/h |
| Maximum Tractive Force | 471260 lb | 661160 lb | 265860 lbf |
| Gradeability - Travel Drives - Maximum | 57 % | 39 % | - |
| Track Pads - Each Side | 42 | 42 | 45 |
| Bottom Rollers - Each Side | 7 | 7 | 8 |
| Support Rollers - Each Side | 2 plus a skid plate in between | 2 plus a skid plate in between | 3 |
| Travel Drives - Each Side | 1 planetary transmission with 2 two-stage axial piston motors | 1 planetary transmission with 2 two-stage axial piston motors | 1 planetary transmission with 2 two-stage axial piston motors |
| Parking Brake | Wet multiple disc brake, spring applied/hydraulically released | - | - |
| Components (1) | All running surfaces of sprockets, idlers, rollers and track links are hardened | HD tracks with cast double-grouser track pad | Forged double-grouser track pads |
| Components (2) | Acoustic travel alarm | HD fixed axle rollers and idlers | Chain links connected by hardened pins and bushings |
| Components (3) | Cast double-grouser combined pad-links with bushings connected by hardened full floating pins | Hardened running surfaces of sprockets, idlers, rollers, pad links, and teeth contact areas | All running surfaces of sprockets, idlers, rollers and track chain links hardened |
| Components (4) | All teeth contact areas of sprocket and pad links are hardened | Acoustic travel alarm (forward and reverse) | Fully hydraulic self-adjusting track tensioning system with accumulator |
| Components (5) | Fully hydraulic self-adjusting track tensioning system with membrane accumulator | Fully hydraulic, self-adjusting track tensioning system with piston accumulator | Automatic hydraulic retarder valve to prevent overspeed on downhill travel |
| Components (6) | Automatic hydraulic retarder valve to prevent over-speed on downhill travel | Automatic hydraulic retarder valve to prevent over-speed on downhill travel | Audible travel alarm |
| Parking Brakes | - | - | Wet multiple disc brake, spring loaded/hydraulically released |
| Gradeability - Travel Drives | - | - | Approximately 54% |
Operator's Cab |
|||
| Operator's Eye Level - Approximately | 22.31 ft | 24.91 ft | - |
| Internal Dimensions of Cab - Length | 7.22 ft | 7.33 ft | 7.32 ft |
| Internal Dimensions of Cab - Width | 5.25 ft | 5.33 ft | 5.33 ft |
| Internal Dimensions of Cab - Height | 7.05 ft | 6.75 ft | 6.79 ft |
| Components (1) | Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat | Single hydraulically driven HVAC System, with dual system option | Large cab floor window with removable grating for easy cleaning |
| Components (2) | Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, seat heating, safety belt, head- and armrests | In-floor window with removable grate | Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests |
| Components (3) | Roller blinds at all windows | Pneumatically cushioned and multi-adjustable comfort seat with heating, cooling, and lumbar support | Safety switch in operator's seat for automatic motion shutdown |
| Components (4) | Windshield with parallel intermittent wiper/washer | Independently adjustable seat consoles with integrated joysticks | Joystick integrated in adjustable seat armrest |
| Components (5) | All-round safety glass, armored windshield and sliding side window | Operator Protective Guard (Top Guard) (ISO 10262:1998) | Full sized trainer seat with safety belt and work table |
| Components (6) | Operator Protective Guard (Top Guard) | Elevated full-size trainer seat with safety belt and laptop desk | Auxiliary fold-away seat with safety belt for 3rd person |
| Components (7) | Single HVAC with option for Dual HVAC | Additional fold-away auxiliary seat with safety belt | Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant |
| Components (8) | Joystick controls integrated in independently adjustable seat consoles | Operator Presence switch | Windshield with parallel intermittent wiper/washer |
| Components (9) | Fold-away auxiliary seat with safety belt | Monitoring system with 254 mm (10 in) touch screen | Roller blinds |
| Components (10) | External sun shields at side and rear windows | Powered 45 degree access stairway | Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated |
| Components (11) | Sliding emergency ladder (kick-down type) with ladder cage | Emergency egress ladder | Additional emergency ladder in close proximity to emergency escape window |
| Components (12) | Machine access via retractable access stairway, stairway angle approximately 45 degrees, hydraulically operated | FM/AM radio with USB and AUX input | - |
| Components (13) | Robust instrument panel including large colored BCS screen with transflective technology | Roller blinds on 3 front windows | - |
| Board Control System (BCS III) Features (1) | USB, Lan (TCP/IP) and CAN BUS interfaces for data export | - | - |
| Board Control System (BCS III) Features (2) | On-screen PDF documentation (e.g. operating instructions, technical handbook, spare parts catalog, electric circuit diagram) | - | - |
| Board Control System (BCS III) Features (3) | Robust instrument panel including large (12 in) colored touch screen for intuitive handling | - | - |
| Board Control System (BCS III) Features (4) | Electronic monitoring, data logging & diagnostic system for vital signs & service data of engines, hydraulic & lube systems | - | - |
| Board Control System (BCS III) Features (5) | On-screen troubleshooting assistance | - | - |
| Board Control System (BCS III) Features (6) | Graphic charts of logged data | - | - |
| Board Control System (BCS III) Features (7) | Fault memory with storage of related conditions | - | - |
| Components (14) | - | 3 cup holders | - |
| Components (15) | - | Cat Electronic Technician service port | - |
| New BCS Features (1) | - | - | Robust instrument panel including large (254 mm/10 in) color touch screen |
| New BCS Features (3) | - | - | Graphical data logging |
| New BCS Features (4) | - | - | Fault memory capabilities |
| Operator's Eye Level (approximate) | - | - | 18.04 ft |
| New BCS Features (2) | - | - | On-screen troubleshooting assistance |
| New BCS Features (5) | - | - | USB, Lan (TCP/IP) and CAN BUS interfaces for data export |
| New Board Control System (BCS) Features: | - | - | Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system |
Automatic Lubrication System |
|||
| Capacity - Grease Container | 188 gal (US) | 188 gal (US) | - |
| Type (1) | Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control adjust the pause/lube times | Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control to adjust the pause/lube times | Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control |
| Type (2) | System failures displayed by Board Control System | System failures displayed by monitoring system | Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing |
| Type (3) | Grease filters (200 µm) between service station and container, as well as directly behind grease pump | Grease filters (200 µm) between service station and container as well as directly behind grease pump | System condition and failures displayed by Board Control System |
| Type (4) | Connected to the lubrication system are: - pivot points of attachment, bucket and cylinders | Main lube system connections include: pivot points of attachment, bucket and cylinders, raceways of swing roller bearing, and 2 greasing pinions for the internal gearing of swing ring | - |
| Type (5) | Connected to the lubrication system are: - raceways of the swing roller bearing - two greasing pinions for the internal gearing of the swing ring | - | - |
| Capacity - Grease Barrel | - | - | 54 gal (US) |
Attachments |
|||
| All buckets (FS and BH) are equipped with a wear package consisting of: (1) | - Special liner material covering main wear areas inside and outside of bucket - Lip shrouds between teeth | Special liner material covering main wear areas inside and outside of bucket and lip shrouds between teeth | - |
| All buckets (FS and BH) are equipped with a wear package consisting of: (2) | - Wing shrouds on side walls - Heel shrouds at bottom edges | Wing shrouds on side walls and heel shrouds at bottom edges | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (1) | - Automatic roll-back limiter to prevent material spillage - Kinematic assistance to hydraulic forces | Automatic roll-back limiter to prevent material spillage; Kinematic assistance to hydraulic forces | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (2) | - Horizontal automatic constant-angle bucket guidance - Vertical automatic constant-angle bucket guidance | Horizontal Automatic constant-angle bucket guidance; Vertical Automatic constant-angle bucket guidance | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (3) | - Constant boom momentum throughout the whole lift arc - Crowd force assistance | Constant boom momentum throughout the entire lift arc; Crowd force assistance | - |
| Type (1) | Inspection hole in monoboom BH | Catwalks with rails at booms (FS and BH) | - |
| Type (2) | Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve | Guards for shovel cylinders (FS) | - |
| Type (3) | Special wear packages for highly abrasive materials on request | Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve | - |
| Type (4) | Catwalks with rails at boom (FS and BH) | Service access holes from both sides of boom (FS and BH) and stick (FS) | - |
| Type (5) | Welding procedures allow for internal counter-welding (double prep weld) wherever possible | Welding procedures allow for internal counter-welding (double prep weld) wherever possible | - |
| Type (6) | Boom and sticks are stress-relieved after welding | Booms and sticks are stress-relieved after welding | - |
| Type (7) | Boom and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel casting at pivot areas | Booms and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel castings at pivot areas | - |
| Type (8) | Guards for shovel cylinders (FS) | Special wear packages for highly abrasive materials available upon request | - |
Bucket |
|||
| Bucket Capacity - Backhoe (heaped 1:1) | 28.8 yd³ | - | - |
| Bucket Capacity - Face Shovel (heaped 2:1) | 28.8 yd³ | - | - |
| Standard Bucket Capacity - Backhoe (Heaped 1:1) | - | - | 15.7 yd³ |
Retractable Service Station |
|||
| Installation | Retractable service station installed underneath the engine module and easily accessible from ground | Retractable service station installed underneath the engine module and easily accessible from ground. | - |
| Equipped With (1) | - | Quick couplings for: Diesel fuel, Engine coolant - left/right engine, Pump transmission gear oil - left/right engine, Engine oil - left/right engine, Hydraulic oil tank, and grease container | - |
| Equipped With (2) | - | Cat jump-start socket | - |
| Equipped With (3) | - | Indicator lights | - |
Diesel Engine - Lesser Regulated |
|||
| Gross Power - SAE J1995 | - | 3025 HP | 1040 HP |
| Net Power - ISO 9249 | - | 2990 HP | 1037 HP |
| Net Power - SAE J1349 | - | 2821 HP | 1032 HP |
| Emissions | - | Optimized for fuel consumption. | Meets China Nonroad Stage III emissions standards, equivalent to Tier 2 |
Diesel Engine - Highly Regulated |
|||
| Gross Power - SAE J1995 | - | 3015 HP | 1033 HP |
| Net Power - SAE J1349 | - | 2810 HP | 1019 HP |
| Net Power - ISO 9249 | - | 2979 HP | 1024 HP |
| Emissions | - | Meets U.S. EPA Tier 4 Final emission requirements. These engines participate in the U.S. EPA averaging, banking, and trading provisions. | Meets Tier 4 Final and Stage V emissions standards |
Electrical System |
|||
| System Voltage | - | 24 V | 24V |
| Batteries in Series/Parallel Installation | - | 6 x 210 Ah; 12 V each; 630 Ah 24 V in total | - |
| Components (1) | - | 6 maintenance-free batteries | Emergency stop buttons inside cab, accessible from all seating locations, and engine module |
| Components (2) | - | Lockable battery isolator switch | Additional ground-level emergency stop |
| Components (3) | - | Lockable starter isolator switch | 9 LED high-brightness working flood lights: – 7 for working area – 2 for rear end |
| Components (4) | - | 13 LED high-brightness working flood lights | 2 LED high-brightness access flood lights |
| Components (5) | - | 17 LED service lights | 7 LED service lights |
| Components (6) | - | 2 electric horns (1 cab module; 1 oil cooler module) | 1 beacon lamp on cab roof |
| Batteries (12V each) - In Series/Parallel Installation | - | - | 630 Ah – 24V |
| Batteries (12V each) | - | - | 6 × 210 Ah |
| Battery Isolation Relays | - | - | manual lockable disconnect switch and automatic disconnect relay |
Service Refill Capacities |
|||
| Fuel Tank | - | 3136 gal (US) | - |
| Hydraulic Tank | - | 1876 gal (US) | - |
| Hydraulic System - Including Tank | - | 2483 gal (US) | - |
| Engine Oil | - | 86.6 gal (US) | - |
| Cooling System | - | 211.4 gal (US) | - |
| Swing Drive | - | 42.4 gal (US) | - |
| Grease Tank | - | 188 gal (US) | - |
Digging Forces |
|||
| Maximum Crowd Force | - | 494410 lb | - |
| Maximum Breakout Force | - | 388780 lb | 164050 lb |
| Maximum Tearout Force | - | - | 146125 lb |
Working Ranges |
|||
| Maximum Digging Height | - | 51.17 ft | 45.6 ft |
| Maximum Digging Reach | - | 54.17 ft | 52.17 ft |
| Maximum Digging Depth | - | 9.17 ft | 26.57 ft |
Standard Bucket Capacity |
|||
| Face Shovel (heaped 2:1) | - | 44.5 yd³ | - |
| Backhoe (heaped 1:1) | - | 44.5 yd³ | - |
Backhoe Attachment (BH) - Digging Forces |
|||
| Stick Digging Force - ISO | - | 295740 lb | - |
| Bucket Digging Force - ISO | - | 274840 lb | - |
Backhoe Attachment (BH) - Working Range |
|||
| Maximum Digging Height | - | 52.83 ft | - |
| Maximum Digging Reach | - | 62.33 ft | - |
| Maximum Digging Depth | - | 29.17 ft | - |
Attachment |
|||
| Type (5) | - | - | Float valve for boom down function |
| Type (2) | - | - | High-tensile steel with solid steel castings at pivot areas |
| Type (3) | - | - | Boom and stick stress-relieved after welding |
| Type (1) | - | - | Boom and stick torsion-resistant with welded box design |
| Type (4) | - | - | Catwalks with rails at boom |
| Buckets Equipped With | - | - | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
Operating Weights - Backhoe |
|||
| Standard Track Pads | - | - | 2.62 ft |
| Operating Weight | - | - | 507500 lb |
| Ground Pressure | - | - | 31.9 psi |
Hydraulic System with Electronic Pump Management |
|||
| Maximum Swing Oil Flow | - | - | 216 gal/min |
| Maximum Pressure - Attachment | - | - | 4495 psi |
| Filters (4) | - | - | Pressure filters (6 μm) for servo circuit |
| Electronic Pump Management Contains (3) | - | - | Automatic return of main pumps to zero flow |
| Features (2) | - | - | Cooling of pump transmission gear oil |
| Maximum Pressure - Travel | - | - | 4495 psi |
| Maximum Pressure - Swing - Acceleration | - | - | 4495 psi |
| Filters (3) | - | - | Full-flow filters (10 μm) for cooling return circuit |
| Electronic Pump Management Contains (2) | - | - | Dedicated circuit pump allocation |
| Maximum Total Oil Flow | - | - | 621 gal/min |
| Filters (2) | - | - | Full-flow filters (10 μm) for complete return circuit |
| Main Pumps | - | - | 6 × variable swash plate pumps |
| Filters (1) | - | - | Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump |
| Electronic Pump Management Contains (4) | - | - | Automatic rpm reduction of engine speed during working breaks |
| Filters (5) | - | - | Transmission oil filter (40 μm) |
| Electronic Pump Management Contains (5) | - | - | Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature |
| Electronic Pump Management Contains (1) | - | - | Electronic load limit control |
| Features (1) | - | - | Pressure cut-off function for all main pumps |
| Total Volume of Hydraulic Oil | - | - | 925 gal (US) |
| Hydraulic Tank Capacity | - | - | 740 gal (US) |
| Maximum Pressure - Swing - Deceleration | - | - | 5080 psi |
Centralized Service Area |
|||
| Equipped With (3) | - | - | Indicator light for hydraulic tank full |
| Equipped With (1) | - | - | Quick couplings for: – Diesel fuel – Engine coolant – Pump transmission gear oil – Engine oil (oil pan) – Hydraulic oil |
| Features | - | - | Centralized service area accessible from ground level. |
| Equipped With (2) | - | - | Cat jump-start socket |
Operating Specifications |
|||
| Operating Weight | - | - | 254 ton (US) |
| Bucket Payload | - | - | 24 Sh Ton |
Engine - Equivalent to U.S. EPA Tier 2 |
|||
| Gross Power - SAE J1995 | - | - | 1040 HP |
| Engine Model | - | - | Cat C32 ACERT |
| Net Power - SAE J1349 | - | - | 1032 HP |
Diesel Engine - Tier 4 Final |
|||
| Components (1) | - | - | Cat NOx reduction system |
| Components (7) | - | - | Two-stage fuel filter |
| Components (3) | - | - | MEUI™-C fuel system |
| Alternator | - | - | 275A |
| Bore | - | - | 5.71 in |
| Components (4) | - | - | Hydraulically driven radiator fan with variable electronically controlled fan speed |
| No. of Cylinders | - | - | 12 |
| Displacement | - | - | 1959 in³ |
| Fuel Tank Capacity | - | - | 951 gal (US) |
| Components (5) | - | - | Micro processed engine management |
| Rated Speed | - | - | 1,800 min-1 (1,800 rpm) |
| Aspiration | - | - | Turbocharged and air-to-air aftercooled |
| Components (2) | - | - | Dual Diesel Oxidation Catalysts (DOCs) |
| Components (8) | - | - | Additional high-capacity water separator including electric priming pump |
| Components (9) | - | - | Large fuel tank allows for 24 hour machine operation |
| Components (6) | - | - | Heavy-duty air filters |
| Maximum Altitude without Deration | - | - | 2925 m (9,600 ft) – above sea level (a.s.l.) |
| Stroke | - | - | 6.38 in |
| Make and Model | - | - | Cat C32 ACERT |
Diesel Engine - Equivalent to Tier 2 |
|||
| Components (3) | - | - | Heavy-duty air filters |
| Components (4) | - | - | Two-stage fuel filter |
| Fuel Tank Capacity | - | - | 951 gal (US) |
| No. of Cylinders | - | - | 12 |
| Components (2) | - | - | Micro processed engine management |
| Displacement | - | - | 1959 in³ |
| Maximum Altitude without Deration | - | - | 3622 m (11,884 ft) – above sea level (a.s.l.) |
| Bore | - | - | 5.71 in |
| Components (1) | - | - | Hydraulically driven radiator fan with variable electronically controlled fan speed |
| Stroke | - | - | 6.38 in |
| Aspiration | - | - | Turbocharged and air-to-air aftercooled |
| Components (5) | - | - | Additional high-capacity water separator including electric priming pump |
| Rated Speed | - | - | 1800 min-1 (1,800 rpm) |
| Alternator | - | - | 275A |
| Make and Model | - | - | Cat C32 ACERT |
| Components (6) | - | - | Large fuel tank allows for 24 hour machine operation |
Engine - U.S. EPA Tier 4 Final |
|||
| Net Power - SAE J1349 | - | - | 1019 HP |
| Gross Power - SAE J1995 | - | - | 1033 HP |
| Engine Model | - | - | Cat® C32 ACERT™ |
