6040 Hydraulic Mining Shovel

360° View

Video

Product description

The Cat^® 6040 Hydraulic Mining Shovel is trusted on sites around the world — consistently delivering the the productivity you demand with the durability you expect. This proven shovel is known for top performance and high reliability, backed by the on-the-ground support of the Cat dealer network.

But we’re always looking for ways to make the 6040 better. We’ve made improvements that enable peak production — delivering fast cycle times and high digging forces. We’ve increased uptime by making the 6040 more reliable and easier to service. And it’s now available for both highly regulated and lesser regulated countries with engines that meet U.S. EPA Tier 4 Final/EU Stage V standards without the need for DEF — saving time and cost during maintenance.

General

Engine Output - SAE J1995 - 2079HP
Bucket Payload - 43.7ton (US)
Operating Weight - 446ton (US)
Note - Specifications above apply to the HRC Face Shovel configuration. Backhoe and Frontless configurations are also available for both HRC and LRC.

Engine

Engine Model - 2 x Cat C32
Gross Power - SAE J1995 - 2079HP
Net Power - SAE J1349 - 1915HP
Note - Power output relates to highly regulated engines. Lesser regulated engines are also available.

Diesel Engines

Number of Cylinders - Each Engine - 12
Bore - 5.71in
Stroke - 6.38in
Displacement - 1959in³
Aspiration - Turbocharged and air-to-air aftercooled
Components (1) - Additional high-capacity water separator
Components (2) - Two-stage fuel filter including water separator
Components (3) - Heavy-duty air filters
Components (4) - Microprocessed engine management
Components (5) - Hydraulically driven radiator fan with electronically controlled fan speed
Fuel Tank Capacity - 2098gal (US)
Emissions - Meets U.S. EPA Tier 4 Final and EU Stage V emission standards

Electrical System - Diesel Drive

System Voltage - 24V
Batteries in Series/Parallel Installation - 6 x 210 Ah - 12 V each; 630 Ah - 24 V in total
Components (1) - 6 maintenance-free batteries
Components (2) - Battery isolation relays and switches
Components (3) - Emergency stop switches accessible from ground level, in engine module and in operator's cab
Components (4) - 14 LED high-brightness working flood lights
Components (5) - 11 LED high-brightness service lights

Operating Weights

6040 FS - Standard Track Pads - 3.9ft
6040 FS - Operating Weight - 891980lb
6040 FS - Ground Pressure - 24.1 N/cm2 (35.0 psi)
6040 - Standard Track Pads - 3.9ft
6040 - Operating Weight - 897930lb
6040 - Ground Pressure - 24.3 N/cm2 (35.3 psi)
Note - 1600 mm track pads available as option
6040 FS - Note - Other track pads available on request

Hydraulic System with Pump Managing System

Hydraulic Tank Capacity - Diesel Version - Approximately - 898gal (US)
Total Volume of Hydraulic Oil - Diesel Version - Approximately - 1532gal (US)
Main Pumps - Diesel Version - 4 x variable swash plate pumps
Main Pumps - Maximum Oil Flow - Diesel Version - 4 x 724 L/min (4 x 191 gal/min)
Maximum Pressure - Attachment - 4350psi
Maximum Pressure - Travel - 5080psi
Swing Pumps - Diesel Version - 4 x reversible swash plate pump
Swing Pumps - Maximum Oil Flow - Diesel Version - 4 x 321 L/min (4 x 85 gal/min)
Maximum Pressure - Swing Pumps - 5080psi

Hydraulic Oil Cooling

Diameter - Fan - 60in
Oil Flow of Cooling Pumps - Diesel Version - 2 x 799 L/min (2 x 211 gal/min)
Features (1) - Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running
Features (2) - Fan speed is thermostatically controlled
Features (3) - Extremely high cooling efficiency to ensure optimum oil temperature
Components (1) - Gear type cooling pumps supplying high-volume, low-pressure oil to aluminum coolers
Components (2) - Variable axial piston pumps supplying low-volume, high-pressure oil to fans
Diameter - Fan - 2 × 1524 mm (2 × 60 in)

Swing System

Swing Drive - 3 compact planetary transmissions with axial piston motors
Parking Brake - Wet multiple disc brake, spring-loaded/hydraulically released
Maximum Swing Speed - Diesel Version - 4.7r/min
Swing Ring - Triple-race roller bearing with sealed internal gearing
Features (1) - Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody
Features (2) - Closed-loop swing circuit with torque control
Features (3) - Hydraulic braking of the swing motion by counteracting control
Features (4) - All raceways and the internal gearing of swing ring supplied by automatic central lubrication system

Undercarriage

Travel Speed - 1st Stage - Maximum - 0.93mile/h
Travel Speed - 2nd Stage - Maximum - 1.55mile/h
Maximum Tractive Force - 471260lb
Gradeability - Travel Drives - Maximum - 57%
Track Pads - Each Side - 42
Bottom Rollers - Each Side - 7
Support Rollers - Each Side - 2 plus a skid plate in between
Travel Drives - Each Side - 1 planetary transmission with 2 two-stage axial piston motors
Parking Brake - Wet multiple disc brake, spring applied/hydraulically released
Components (1) - All running surfaces of sprockets, idlers, rollers and track links are hardened
Components (2) - Acoustic travel alarm
Components (3) - Cast double-grouser combined pad-links with bushings connected by hardened full floating pins
Components (4) - All teeth contact areas of sprocket and pad links are hardened
Components (5) - Fully hydraulic self-adjusting track tensioning system with membrane accumulator
Components (6) - Automatic hydraulic retarder valve to prevent over-speed on downhill travel

Operator's Cab

Operator's Eye Level - Approximately - 22.31ft
Internal Dimensions of Cab - Length - 7.22ft
Internal Dimensions of Cab - Width - 5.25ft
Internal Dimensions of Cab - Height - 7.05ft
Components (1) - Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat
Components (2) - Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, seat heating, safety belt, head- and armrests
Components (3) - Roller blinds at all windows
Components (4) - Windshield with parallel intermittent wiper/washer
Components (5) - All-round safety glass, armored windshield and sliding side window
Components (6) - Operator Protective Guard (Top Guard)
Components (7) - Single HVAC with option for Dual HVAC
Components (8) - Joystick controls integrated in independently adjustable seat consoles
Components (9) - Fold-away auxiliary seat with safety belt
Components (10) - External sun shields at side and rear windows
Components (11) - Sliding emergency ladder (kick-down type) with ladder cage
Components (12) - Machine access via retractable access stairway, stairway angle approximately 45 degrees, hydraulically operated
Components (13) - Robust instrument panel including large colored BCS screen with transflective technology
Board Control System (BCS III) Features (1) - USB, Lan (TCP/IP) and CAN BUS interfaces for data export
Board Control System (BCS III) Features (2) - On-screen PDF documentation (e.g. operating instructions, technical handbook, spare parts catalog, electric circuit diagram)
Board Control System (BCS III) Features (3) - Robust instrument panel including large (12 in) colored touch screen for intuitive handling
Board Control System (BCS III) Features (4) - Electronic monitoring, data logging & diagnostic system for vital signs & service data of engines, hydraulic & lube systems
Board Control System (BCS III) Features (5) - On-screen troubleshooting assistance
Board Control System (BCS III) Features (6) - Graphic charts of logged data
Board Control System (BCS III) Features (7) - Fault memory with storage of related conditions

Automatic Lubrication System

Capacity - Grease Container - 188gal (US)
Type (1) - Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control adjust the pause/lube times
Type (2) - System failures displayed by Board Control System
Type (3) - Grease filters (200 µm) between service station and container, as well as directly behind grease pump
Type (4) - Connected to the lubrication system are: - pivot points of attachment, bucket and cylinders
Type (5) - Connected to the lubrication system are: - raceways of the swing roller bearing - two greasing pinions for the internal gearing of the swing ring

Attachments

All buckets (FS and BH) are equipped with a wear package consisting of: (1) - - Special liner material covering main wear areas inside and outside of bucket - Lip shrouds between teeth
All buckets (FS and BH) are equipped with a wear package consisting of: (2) - - Wing shrouds on side walls - Heel shrouds at bottom edges
Shovel attachment with unique TriPower kinematics ensuring the following main features: (1) - - Automatic roll-back limiter to prevent material spillage - Kinematic assistance to hydraulic forces
Shovel attachment with unique TriPower kinematics ensuring the following main features: (2) - - Horizontal automatic constant-angle bucket guidance - Vertical automatic constant-angle bucket guidance
Shovel attachment with unique TriPower kinematics ensuring the following main features: (3) - - Constant boom momentum throughout the whole lift arc - Crowd force assistance
Type (1) - Inspection hole in monoboom BH
Type (2) - Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve
Type (3) - Special wear packages for highly abrasive materials on request
Type (4) - Catwalks with rails at boom (FS and BH)
Type (5) - Welding procedures allow for internal counter-welding (double prep weld) wherever possible
Type (6) - Boom and sticks are stress-relieved after welding
Type (7) - Boom and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel casting at pivot areas
Type (8) - Guards for shovel cylinders (FS)

Bucket

Bucket Capacity - Backhoe (heaped 1:1) - 28.8yd³
Bucket Capacity - Face Shovel (heaped 2:1) - 28.8yd³

Retractable Service Station

Installation - Retractable service station installed underneath the engine module and easily accessible from ground

Standard Equipment:

Cat Powertrain
- 2 x Cat 3512E engines
- Aftertreatment System (used in highly regulated countries only): -Diesel Oxidation Catalysts (DOCs) -Non-DEF solution
- Air-to-Air After Cooling (ATAAC)
- Turbocharger
- Hydraulically driven radiator fan
- Electronically controlled fan speed
- Micro processed engine management
- Heavy-duty air filters
- Two-stage fuel filter with series filtration
- High-capacity water seperator
- Starting aid -- automatic ether
- Exhaust manifold and turbo heat shields
- Dual 24 V electric starters per engine
- Automatic engine idle shut down
Hydraulics
- Automatic fuel priming
- Hydraulic Optimization
- Operator Assist: Enhanced Motion Control
- Cat Hydraulic Hose assemblies
- Pump managing system with: -Electronic load limit control -Flow on demand -Automatic zero flow regulation -Automatic engine rpm reduction -Reduced oil flow at high hydraulic oil or engine temperature
- Pressure cut-off for main pumps
- Cooling of pump transmission gear oil
- Closed loop swing circuit
- Pressure testing points
- Full-flow high-pressure filters (100 μm), main pumps
- High pressure filters (100 μm), closed swing circuit
- Full-flow filters (10 μm), return circuit
- Pressure filters swing charge circuit (40 μm)
- Pressure filters pilot circuit (6 μm)
- Transmission oil filters (40 μm)
- Boom float valve (FS and BH)
- Stick float valve (FS)
Electrical System
- 6 Maintenance-free batteries
- Lockable battery isolator switch
- Lockable starter isolator switch
- 13 LED high-brightness working flood lights
- 17 LED service lights
- 2 acoustic travel alarms -forward and reverse (power module, oil cooler module)
- 2 electric horns (1 cab module, 1 oil cooler module)
Undercarriage
- HD tracks with cast double-grouser track pads
- 1400 mm (4'7") wide track pads
- HD fixed axle carrier and load rollers
- HD fixed axle idlers
- Automatic hydraulic retarder valve
- Hinged travel motor covers
- Hardened running surfaces of sprockets, idlers, rollers, pad links, teeth contact areas
- Fully hydraulic self-adjusting track tensioning system with piston accumulators
Automatic Lubrication System
- Rectangular grease container (fill via service station)
- Lubricated pinion in swing ring
- Grease filters (200 μm)
Operator Environment
- Single hydraulically driven HVAC system
- In-floor window with removable grate
- Pneumatically cushioned and multiadjustable comfort seat with: -Heating and cooling -Lumbar support -2-point safety belt -Head and arm rests -Safety switch for automatic motion shutdown
- Independently adjustable seat consoles with integrated joysticks
- Electronic-Hydraulic Servo Control
- Elevated full-size trainer seat with 2-point safety belt and laptop desk
- Additional fold-away auxiliary seat with 2-point safety belt
- Three cup holders
- FM/AM radio with USB and AUX input
- Parallel intermittent wiper/washer
- Roller blinds
- Monitoring system with 254 mm (10 in) color touchscreen
- 45° stairway from engine bay to operator cab
- Powered 45° access stairway
- Heated mirror on LH side
- Camera monitoring system (Right and rear cameras, 2 lights, and additional display)
- Level indicators for length and crosswise inclination
- Document Storage
Front Attachment
- Service access holes from both sides in boom and stick (FS and BH)
- Boom and stick thermally stress relieved after welding
- Catwalks with rails at boom (FS and BH)
- Wear Package (as per bucket selection)
Cat Technology
- Cat Product Link^™ Elite (Cellular)
- Cat MineStar^™ Solutions Ready
Service And Maintenance
- Engine oil exchange interval -- 500 hours
- Hydraulic oil change interval -10,000 hours
- Scheduled Oil Sampling (S·O·SSM) ports
- Retractable ground level service station with quick couplings for: -Diesel fuel -Engine coolant -left/right engines -Pump transmission gear oil -left/right engines -Engine oil -left/right engines -Engine oil extension tanks -Hydraulic oil -Grease -Swing transmission gear oil
- Cat battery charging connector
- Indicator lights
- Cat Electronic Technician service port
- Dirt wiper at swivel
Safety And Security
- Emergency stop switches: 2 in cab, 5 in engine module, 1 at ground level service station, 1 pull rope accessible from ground level
- Operator Protective Guard (Top Guard)
- All-round safety glass
- Emergency egress ladder
Miscellaneous
- ISO or ANSI decals

Optional Equipment:

General
- Engine oil interval extension kit, up to 1,000 hrs
Superstructure
- Round container(s) for standard 200 L (53 gal) barrels (instead of 710 L (188 gal) grease container)
- Filling of round container(s) via service station
- Various cold-weather options
Cab
- Dual (redundancy) heating ventilating and air conditioning system
- Cab heating
- Camera monitoring system (two cameras and additional color display)
Undercarriage
- Track pad width 1600 mm (5 ft 3 in) - Non HD
- Automatic lubrication of rollers by central lube system
- Belly plate for additional undercarriage protection
- Additional optional equipment available on request.

Compare Products

Download Brochure