Compare Equipment Go Back
6020B Hydraulic Shovel |
6060 Hydraulic Mining Shovel |
6015 Hydraulic Shovel |
|
General |
|||
---|---|---|---|
Engine Output - SAE J1995 | 1040 HP | 3015 HP | 824 HP |
Bucket Payload | 23.8 ton (US) | 67 ton (US) | 16.1 ton (US) |
Operating Weight | 253.8 ton (US) | 660 ton (US) | 154.3 ton (US) |
Note | Specifications shown above apply to a Backhoe configuration. A frontless configuration is also available. | Specifications shown above apply to Face Shovel configuration. Backhoe and Frontless configurations are also available. | Specifications shown above apply to highly regulated, backhoe configuration. Lesser regulated and frontless configurations are also available. |
Standard Bucket Capacity | 15.7 yd³ | - | - |
Electrical System |
|||
Batteries (12V each) - In Series/Parallel Installation | 630 Ah – 24V | - | - |
Components (3) | 9 LED high-brightness working flood lights: – 7 for working area – 2 for rear end |
Lockable starter isolator switch | Lockable battery isolation switch |
Batteries (12V each) | 6 × 210 Ah | - | - |
Components (1) | Emergency stop buttons inside cab, accessible from all seating locations, and engine module | 6 maintenance-free batteries | Emergency stop in cabin, engine module, pump room and on service station accessible from ground level |
Components (2) | Additional ground-level emergency stop | Lockable battery isolator switch | Four maintenance free batteries |
System Voltage | 24V | 24 V | 24 V |
Battery Isolation Relays | manual lockable disconnect switch and automatic disconnect relay | - | - |
Components (6) | 1 beacon lamp on cab roof | 2 electric horns (1 cab module; 1 oil cooler module) | 2 electric horns |
Components (5) | 7 LED service lights | 17 LED service lights | 14 LED high-brightness working lights |
Components (4) | 2 LED high-brightness access flood lights | 13 LED high-brightness working flood lights | 5 LED service lights |
Batteries in Series/Parallel Installation | - | 6 x 210 Ah; 12 V each; 630 Ah 24 V in total | - |
Batteries | - | - | 4 × 200 Ah (12 V each) |
Alternator Rating | - | - | 150 A (24 V) in total |
Components (7) | - | - | Two (2) lights for rear end |
Components (9) | - | - | One (1) beacon light on cabin roof |
Components (8) | - | - | One (1) light for machine deck/service |
Hydraulic Oil Cooling |
|||
Features (2) | Variable electronically controlled flow of oil through cooler and fan speed | Fan speed and flow of oil to the coolers are thermostatically controlled | - |
Oil Flow of Cooling Pumps | 211 gal/min | 4 x 488 L/min (4 x 129 gal/min) | - |
Diameter - Fan | 4.92 ft | 46 in | - |
Features (1) | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running | - |
Features (3) | Superior cooling efficiency to ensure optimum oil temperature | Extremely high cooling efficiency to ensure optimum oil temperature | - |
Components | - | 4 cooling fans | - |
Features (4) | - | Gear-type cooling pumps supplying high-volume, low-pressure oil to fans and aluminum coolers | - |
Operator's Cab |
|||
Components (5) | Full sized trainer seat with safety belt and work table | Operator Protective Guard (Top Guard) (ISO 10262:1998) | Removable lower windshield with in cab storage bracket |
Internal Dimensions of Cab - Width | 5.33 ft | 5.33 ft | - |
Components (7) | Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant | Additional fold-away auxiliary seat with safety belt | Beverage holder |
Components (9) | Roller blinds | Monitoring system with 254 mm (10 in) touch screen | AM/FM radio |
Components (11) | Additional emergency ladder in close proximity to emergency escape window | Emergency egress ladder | Two stereo speakers |
Internal Dimensions of Cab - Length | 7.32 ft | 7.33 ft | - |
Components (8) | Windshield with parallel intermittent wiper/washer | Operator Presence switch | Literature holder |
Components (2) | Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests | In-floor window with removable grate | Heated cab mirror |
New BCS Features (1) | Robust instrument panel including large (254 mm/10 in) color touch screen | - | - |
New BCS Features (3) | Graphical data logging | - | - |
New BCS Features (4) | Fault memory capabilities | - | - |
Operator's Eye Level (approximate) | 18.04 ft | - | - |
New BCS Features (2) | On-screen troubleshooting assistance | - | - |
Components (10) | Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated | Powered 45 degree access stairway | Radio with MP3 auxiliary audio port |
New BCS Features (5) | USB, Lan (TCP/IP) and CAN BUS interfaces for data export | - | - |
Components (3) | Safety switch in operator's seat for automatic motion shutdown | Pneumatically cushioned and multi-adjustable comfort seat with heating, cooling, and lumbar support | Sliding upper door window (left-hand cab door) |
Internal Dimensions of Cab - Height | 6.79 ft | 6.75 ft | - |
Components (1) | Large cab floor window with removable grating for easy cleaning | Single hydraulically driven HVAC System, with dual system option | Pressurized operator station with positive filtration |
Components (4) | Joystick integrated in adjustable seat armrest | Independently adjustable seat consoles with integrated joysticks | Glass-breaking safety hammer |
New Board Control System (BCS) Features: | Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system | - | - |
Components (6) | Auxiliary fold-away seat with safety belt for 3rd person | Elevated full-size trainer seat with safety belt and laptop desk | Joystick Controls Alternate Patterns including ISO/JIS, BHL, MHI, KOBE, or SCM |
Operator's Eye Level - Approximately | - | 24.91 ft | - |
Components (12) | - | FM/AM radio with USB and AUX input | Storage shelf suitable for lunch or toolbox |
Components (13) | - | Roller blinds on 3 front windows | Color LCD display with warning, filter/fluid change, and working hour information |
Components (14) | - | 3 cup holders | Adjustable armrest |
Components (15) | - | Cat Electronic Technician service port | Height-adjustable joystick consoles |
Components (16) | - | - | Neutral lever (lock out) for all controls |
Components (17) | - | - | Travel control pedals with removable hand levers |
Components (18) | - | - | Two power outlets, 10 amp (total) |
Components (19) | - | - | Laminated glass front upper window and tempered other windows |
Swing System |
|||
Swing Ring | Triple-race roller bearing with sealed internal gearing | Triple-race roller bearing with sealed internal gearing | Cross roller bearing with sealed internal gearing |
Maximum Swing Speed | 4.9 r/min | 3.8 r/min | 4.9 r/min |
Swing Drive | 2 compact planetary transmissions with axial piston motors | 4 compact planetary transmissions with axial piston motors | Two (2) compact planetary transmissions with axial piston motors |
Parking Brake | Wet multiple-disc brake, spring-loaded/hydraulically released | - | Wet multiple disc brake, spring-loaded/hydraulically released |
Features (2) | All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system | Closed-loop swing circuit with torque control | Hydraulic braking of swing motion when control is returned to neutral position or by counteracting control for stronger braking |
Features (1) | Open swing circuit with auto slow down when joysticks in neutral | Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody | Closed-loop swing circuit with speed control |
Parking Brakes | - | Wet multiple disc brake, spring loaded/hydraulically released | - |
Features (3) | - | Hydraulic braking of the swing motion by counteracting control | All raceways and the internal gearing of swing ring supplied by automatic central lubrication system |
Features (4) | - | All raceways and the internal gearing of swing ring, supplied by automatic central lubrication system | - |
Undercarriage |
|||
Track Pads - Each Side | 45 | 42 | - |
Components (1) | Forged double-grouser track pads | HD tracks with cast double-grouser track pad | Forged double-grouser track pads |
Components (6) | Audible travel alarm | Automatic hydraulic retarder valve to prevent over-speed on downhill travel | Automatic hydraulic retarder valve to prevent overspeed on downhill travel |
Bottom Rollers - Each Side | 8 | 7 | - |
Travel Speed - 1st Stage - Maximum | 0.68 mile/h | 0.68 mile/h | - |
Components (4) | Fully hydraulic self-adjusting track tensioning system with accumulator | Acoustic travel alarm (forward and reverse) | All running surfaces of sprockets, idlers, rollers and track chain links hardened |
Components (5) | Automatic hydraulic retarder valve to prevent overspeed on downhill travel | Fully hydraulic, self-adjusting track tensioning system with piston accumulator | Fully hydraulic self-adjusting track tensioning system with accumulator |
Parking Brakes | Wet multiple disc brake, spring loaded/hydraulically released | - | - |
Travel Speed - 2nd Stage - Maximum | 1.49 mile/h | 0.99 mile/h | - |
Gradeability - Travel Drives | Approximately 54% | - | 38°/78% (SAE J1309) |
Components (3) | All running surfaces of sprockets, idlers, rollers and track chain links hardened | Hardened running surfaces of sprockets, idlers, rollers, pad links, and teeth contact areas | Postive Pin Retention (PPR2) sealed and greased track design |
Maximum Tractive Force | 265860 lbf | 661160 lb | 197157 lbf |
Travel Drives - Each Side | 1 planetary transmission with 2 two-stage axial piston motors | 1 planetary transmission with 2 two-stage axial piston motors | - |
Components (2) | Chain links connected by hardened pins and bushings | HD fixed axle rollers and idlers | Chain links connected by hardened pins and bushings |
Support Rollers - Each Side | 3 | 2 plus a skid plate in between | - |
Gradeability - Travel Drives - Maximum | - | 39 % | - |
Travel Speed - Two Stages - 1st Stage - Maximum | - | - | 1.6 mile/h |
Travel Speed - Two Stages - 2nd Stage - Maximum | - | - | 2.3 mile/h |
Maximum Drawbar Pull - Forward | - | - | 192886 lbf |
Maximum Drawbar Pull - Reverse | - | - | 220987 lbf |
Hydraulic Track Tensioning | - | - | With accumulator |
Number of Shoes - Each Side | - | - | 46 |
Number of Track Rollers - Each Side | - | - | 9 |
Number of Carrier Rollers - Each Side | - | - | 3 |
Components (7) | - | - | Audible travel alarm |
Automatic Lubrication System |
|||
Type (3) | System condition and failures displayed by Board Control System | Grease filters (200 µm) between service station and container as well as directly behind grease pump | Standard grease reel on machine for bucket linkage |
Capacity - Grease Barrel | 54 gal (US) | - | 18 gal (US) |
Type (1) | Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control | Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control to adjust the pause/lube times | Central bank lubrication system |
Type (2) | Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing | System failures displayed by monitoring system | Grease is automatically applied to all attachment pivot points (except bucket linkage) and slew bearing |
Capacity - Grease Container | - | 188 gal (US) | - |
Type (4) | - | Main lube system connections include: pivot points of attachment, bucket and cylinders, raceways of swing roller bearing, and 2 greasing pinions for the internal gearing of swing ring | Grease refill service point accessible from ground |
Attachment |
|||
Type (5) | Float valve for boom down function | - | - |
Type (2) | High-tensile steel with solid steel castings at pivot areas | - | - |
Type (3) | Boom and stick stress-relieved after welding | - | - |
Type (1) | Boom and stick torsion-resistant with welded box design | - | - |
Type (4) | Catwalks with rails at boom | - | - |
Buckets Equipped With | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
- | - |
Operating Weights - Backhoe |
|||
Standard Track Pads | 2.62 ft | - | - |
Operating Weight | 507500 lb | - | 154 ton (US) |
Ground Pressure | 31.9 psi | - | - |
Hydraulic System with Electronic Pump Management |
|||
Maximum Swing Oil Flow | 216 gal/min | - | - |
Maximum Pressure - Attachment | 4495 psi | - | - |
Filters (4) | Pressure filters (6 μm) for servo circuit | - | - |
Electronic Pump Management Contains (3) | Automatic return of main pumps to zero flow | - | - |
Features (2) | Cooling of pump transmission gear oil | - | - |
Maximum Pressure - Travel | 4495 psi | - | - |
Maximum Pressure - Swing - Acceleration | 4495 psi | - | - |
Filters (3) | Full-flow filters (10 μm) for cooling return circuit | - | - |
Electronic Pump Management Contains (2) | Dedicated circuit pump allocation | - | - |
Maximum Total Oil Flow | 621 gal/min | - | - |
Filters (2) | Full-flow filters (10 μm) for complete return circuit | - | - |
Main Pumps | 6 × variable swash plate pumps | - | - |
Filters (1) | Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump | - | - |
Electronic Pump Management Contains (4) | Automatic rpm reduction of engine speed during working breaks | - | - |
Filters (5) | Transmission oil filter (40 μm) | - | - |
Electronic Pump Management Contains (5) | Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature | - | - |
Electronic Pump Management Contains (1) | Electronic load limit control | - | - |
Features (1) | Pressure cut-off function for all main pumps | - | - |
Total Volume of Hydraulic Oil | 925 gal (US) | - | - |
Hydraulic Tank Capacity | 740 gal (US) | - | - |
Maximum Pressure - Swing - Deceleration | 5080 psi | - | - |
Centralized Service Area |
|||
Equipped With (3) | Indicator light for hydraulic tank full | - | - |
Equipped With (1) | Quick couplings for: – Diesel fuel – Engine coolant – Pump transmission gear oil – Engine oil (oil pan) – Hydraulic oil |
- | Emergency stop |
Features | Centralized service area accessible from ground level. | - | - |
Equipped With (2) | Cat jump-start socket | - | Quick couplings for: Diesel fuel and Grease |
Feature | - | - | Accessible from ground level |
Digging Forces |
|||
Maximum Tearout Force | 146125 lb | - | - |
Maximum Breakout Force | 164050 lb | 388780 lb | - |
Maximum Crowd Force | - | 494410 lb | - |
Working Ranges |
|||
Maximum Digging Reach | 52.17 ft | 54.17 ft | - |
Maximum Digging Depth | 26.57 ft | 9.17 ft | - |
Maximum Digging Height | 45.6 ft | 51.17 ft | - |
Operating Specifications |
|||
Operating Weight | 254 ton (US) | - | - |
Bucket Payload | 24 Sh Ton | - | - |
Bucket |
|||
Standard Bucket Capacity - Backhoe (Heaped 1:1) | 15.7 yd³ | - | - |
Engine - Equivalent to U.S. EPA Tier 2 |
|||
Gross Power - SAE J1995 | 1040 HP | - | 839 HP |
Engine Model | Cat C32 ACERT | - | Cat® C27 |
Net Power - SAE J1349 | 1032 HP | - | 746 HP |
Diesel Engine - Lesser Regulated |
|||
Gross Power - SAE J1995 | 1040 HP | 3025 HP | - |
Net Power - ISO 9249 | 1037 HP | 2990 HP | - |
Net Power - SAE J1349 | 1032 HP | 2821 HP | - |
Emissions | Meets China Nonroad Stage III emissions standards, equivalent to Tier 2 | Optimized for fuel consumption. | - |
Diesel Engine - Tier 4 Final |
|||
Components (1) | Cat NOx reduction system | - | - |
Components (7) | Two-stage fuel filter | - | - |
Components (3) | MEUI™-C fuel system | - | - |
Alternator | 275A | - | - |
Bore | 5.71 in | - | - |
Components (4) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
No. of Cylinders | 12 | - | - |
Displacement | 1959 in³ | - | - |
Fuel Tank Capacity | 951 gal (US) | - | - |
Components (5) | Micro processed engine management | - | - |
Rated Speed | 1,800 min-1 (1,800 rpm) | - | - |
Aspiration | Turbocharged and air-to-air aftercooled | - | - |
Components (2) | Dual Diesel Oxidation Catalysts (DOCs) | - | - |
Components (8) | Additional high-capacity water separator including electric priming pump | - | - |
Components (9) | Large fuel tank allows for 24 hour machine operation | - | - |
Components (6) | Heavy-duty air filters | - | - |
Maximum Altitude without Deration | 2925 m (9,600 ft) – above sea level (a.s.l.) | - | - |
Stroke | 6.38 in | - | - |
Make and Model | Cat C32 ACERT | - | - |
Diesel Engine - Equivalent to Tier 2 |
|||
Components (3) | Heavy-duty air filters | - | - |
Components (4) | Two-stage fuel filter | - | - |
Fuel Tank Capacity | 951 gal (US) | - | - |
No. of Cylinders | 12 | - | - |
Components (2) | Micro processed engine management | - | - |
Displacement | 1959 in³ | - | - |
Maximum Altitude without Deration | 3622 m (11,884 ft) – above sea level (a.s.l.) | - | - |
Bore | 5.71 in | - | - |
Components (1) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
Stroke | 6.38 in | - | - |
Aspiration | Turbocharged and air-to-air aftercooled | - | - |
Components (5) | Additional high-capacity water separator including electric priming pump | - | - |
Rated Speed | 1800 min-1 (1,800 rpm) | - | - |
Alternator | 275A | - | - |
Make and Model | Cat C32 ACERT | - | - |
Components (6) | Large fuel tank allows for 24 hour machine operation | - | - |
Diesel Engine - Highly Regulated |
|||
Gross Power - SAE J1995 | 1033 HP | 3015 HP | - |
Net Power - ISO 9249 | 1024 HP | 2979 HP | - |
Net Power - SAE J1349 | 1019 HP | 2810 HP | - |
Emissions | Meets Tier 4 Final and Stage V emissions standards | Meets U.S. EPA Tier 4 Final emission requirements. These engines participate in the U.S. EPA averaging, banking, and trading provisions. | - |
Engine - U.S. EPA Tier 4 Final |
|||
Net Power - SAE J1349 | 1019 HP | - | 746 HP |
Gross Power - SAE J1995 | 1033 HP | - | 824 HP |
Engine Model | Cat® C32 ACERT™ | - | Cat® C27 |
Engine |
|||
Engine Model | - | 2 x Cat 3512E | - |
Emissions | - | - | U.S. EPA Tier 4 Final and EU Stage V; China Nonroad Stage III, equivalent to U.S. EPA Tier 2; Equivalent to U.S. EPA Tier 1 |
Diesel Engines |
|||
Rated Speed | - | 1,800 min-1 (1,800 rpm) | - |
Number of Cylinders - Each Engine | - | 12 | - |
Bore | - | 6.69 in | - |
Stroke | - | 8.46 in | - |
Displacement | - | 3574 in³ | - |
Aspiration | - | Turbocharged and charge air-cooled | - |
Components (1) | - | Non-DEF Aftertreatment system with Diesel Oxidation Catalysts (DOCs) | - |
Components (2) | - | High-capacity water separator | - |
Components (3) | - | Two-stage fuel filter with series filtration | - |
Components (4) | - | Heavy-duty air filters | - |
Components (5) | - | Microprocessed engine management | - |
Components (6) | - | Hydraulically driven radiator fan with electronically controlled fan speed | - |
Components (7) | - | Exhaust manifold and turbo heat shields | - |
Operating Weights |
|||
6060 FS - Standard Track Pads | - | 4.58 ft | - |
6060 FS - Operating Weight | - | 1320110 lb | - |
6060 FS - Ground Pressure | - | 26.6 N/cm2 (38.5 psi) | - |
Backhoe - Standard Track Pads | - | 4.58 ft | - |
Backhoe - Operating Weight | - | 1323860 lb | - |
Backhoe - Ground Pressure | - | 26.7 N/cm2 (38.7 psi) | - |
Note | - | Operating weights include: base machine, front attachment, standard track pads, standard rock bucket, 100% fuel and lubricants. | - |
Service Refill Capacities |
|||
Fuel Tank | - | 3136 gal (US) | 449 gal (US) |
Hydraulic Tank | - | 1876 gal (US) | 253 gal (US) |
Hydraulic System - Including Tank | - | 2483 gal (US) | 463 gal (US) |
Engine Oil | - | 86.6 gal (US) | 23 gal (US) |
Cooling System | - | 211.4 gal (US) | 44 gal (US) |
Swing Drive | - | 42.4 gal (US) | 2.4 gal (US) |
Grease Tank | - | 188 gal (US) | 18 gal (US) |
Hydraulic System with Pump Managing System |
|||
Main Pumps - Diesel Version | - | 8 variable swash plate pumps | - |
Main Pumps - Maximum Oil Flow - Diesel Version | - | 8 x 650 L/min (8 x 172 gal/min) | - |
Maximum Pressure - Attachment | - | 4640 psi | - |
Maximum Pressure - Travel | - | 5220 psi | - |
Swing Pumps - Diesel Version | - | 4 reversible swash plate pumps | - |
Swing Pumps - Maximum Oil Flow - Diesel Version | - | 4 x 352 L/min (4 x 93 gal/min) | - |
Maximum Pressure - Swing Pumps | - | 5075 psi | - |
Attachments |
|||
Shovel attachment with unique TriPower kinematics ensuring the following main features: (1) | - | Automatic roll-back limiter to prevent material spillage; Kinematic assistance to hydraulic forces | - |
Shovel attachment with unique TriPower kinematics ensuring the following main features: (2) | - | Horizontal Automatic constant-angle bucket guidance; Vertical Automatic constant-angle bucket guidance | - |
Shovel attachment with unique TriPower kinematics ensuring the following main features: (3) | - | Constant boom momentum throughout the entire lift arc; Crowd force assistance | - |
All buckets (FS and BH) are equipped with a wear package consisting of: (1) | - | Special liner material covering main wear areas inside and outside of bucket and lip shrouds between teeth | - |
All buckets (FS and BH) are equipped with a wear package consisting of: (2) | - | Wing shrouds on side walls and heel shrouds at bottom edges | - |
Type (1) | - | Catwalks with rails at booms (FS and BH) | Boom and stick torsion-resistant with welded box design |
Type (2) | - | Guards for shovel cylinders (FS) | High-tensile steel with solid steel castings at pivot areas |
Type (3) | - | Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve | Boom and stick stress-relieved after welding |
Type (4) | - | Service access holes from both sides of boom (FS and BH) and stick (FS) | Float valve for boom down function |
Type (5) | - | Welding procedures allow for internal counter-welding (double prep weld) wherever possible | - |
Type (6) | - | Booms and sticks are stress-relieved after welding | - |
Type (7) | - | Booms and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel castings at pivot areas | - |
Type (8) | - | Special wear packages for highly abrasive materials available upon request | - |
Buckets Equipped With | - | - | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
Standard Bucket Capacity |
|||
Face Shovel (heaped 2:1) | - | 44.5 yd³ | - |
Backhoe (heaped 1:1) | - | 44.5 yd³ | - |
Backhoe Attachment (BH) - Digging Forces |
|||
Stick Digging Force - ISO | - | 295740 lb | 104761 lbf |
Bucket Digging Force - ISO | - | 274840 lb | 120947 lbf |
Bucket Digging Force - SAE | - | - | 112600 lbf |
Stick Digging Force - SAE | - | - | 98800 lbf |
Backhoe Attachment (BH) - Working Range |
|||
Maximum Digging Height | - | 52.83 ft | 41.9 ft |
Maximum Digging Reach | - | 62.33 ft | 45.6 ft |
Maximum Digging Depth | - | 29.17 ft | 26.3 ft |
Maximum Dump Height | - | - | 27.9 ft |
Retractable Service Station |
|||
Installation | - | Retractable service station installed underneath the engine module and easily accessible from ground. | - |
Equipped With (1) | - | Quick couplings for: Diesel fuel, Engine coolant - left/right engine, Pump transmission gear oil - left/right engine, Engine oil - left/right engine, Hydraulic oil tank, and grease container | - |
Equipped With (2) | - | Cat jump-start socket | - |
Equipped With (3) | - | Indicator lights | - |
Engine - Cat C27 with Tier 4 Final Emission Standards |
|||
Number of Cylinders | - | - | 12 |
Bore | - | - | 5.4 in |
Stroke | - | - | 6 in |
Displacement | - | - | 1648 in³ |
Engine - Cat C27 with Tier 1 or Tier 2 Equivalent Emission Standards |
|||
Number of Cylinders | - | - | 12 |
Bore | - | - | 5.4 in |
Stroke | - | - | 6 in |
Displacement | - | - | 1648 in³ |
Aspiration | - | - | Turbocharged and air-to-air aftercooled |
Weights |
|||
Ground Pressure | - | - | 23.6 psi |
Note | - | - | Operating weight includes: 700 mm (28 in) track shoes, 7.6 m (24 ft 11 in) boom, 3.4 m (11 ft 2 in) stick, standard rock bucket, 100% fuel and lubricants |
Operating Weight | - | - | 308000 lb |
Track |
|||
Standard | - | - | 28 in |
Wide | - | - | 36 in |
Extra Wide | - | - | 39 in |
Number of Shoes - Each Side | - | - | 46 |
Number of Track Rollers - Each Side | - | - | 9 |
Number of Carrier Rollers - Each Side | - | - | 3 |
Track Pads | - | - | Double grouser |
Drive |
|||
Travel Speed - Two Stages - 1st Stage - Maximum | - | - | 1.4 mile/h |
Travel Speed - Two Stages - 2nd Stage - Maximum | - | - | 2.1 mile/h |
Maximum Drawbar Pull - Forward | - | - | 192886 lbf |
Maximum Drawbar Pull - Reverse | - | - | 220987 lbf |
Gradeability - Travel Drives | - | - | Approximately 42% |
Hydraulic Track Tensioning | - | - | With accumulator |
Maximum Drawbar Pull | - | - | 179847 lbf |
Hydraulic System |
|||
Main Pumps | - | - | 3 × variable swash plate pumps |
Main Pumps - Maximum Total Oil Flow | - | - | 407 gal/min |
Main Pumps - Maximum Pressure - Attachment | - | - | 4641 psi |
Pilot Pump | - | - | 1 × gear pump |
Pilot Pump - Maximum Flow, Pilot | - | - | 40.4 gal/min |
Pilot Pump - Maximum Pressure, Pilot | - | - | 1378 psi |
Main Pumps - Maximum Pressure - Travel | - | - | 4641 psi |
Swing Pump | - | - | 1 × variable swash plate pump |
Engine Fan Pump - Maximum Flow, Engine Fan | - | - | 53.1 gal/min |
Engine Fan Pump - Maximum Pressure, Engine Fan | - | - | 3191 psi |
Engine Fan Pump | - | - | 1 × variable swash plate pump |
Hydraulic Fan Pump - Maximum Flow, Hydraulic Fan | - | - | 22.7 gal/min |
Swing Pump - Maximum Flow - Swing | - | - | 127 gal/min |
Hydraulic Fan Pump | - | - | 1 × variable swash plate pump |
Hydraulic Fan Pump - Maximum Pressure, Hydraulic Fan | - | - | 1958 psi |
Swing Pump - Maximum Pressure - Swing | - | - | 5294 psi |
Hydraulic Oil Cooling - Maximum Flow | - | - | 284 gal/min |
Hydraulic Oil Cooling - Diameter of Fan | - | - | 40 in |
Filters (1) | - | - | Full-flow high-pressure filters (200 μm) for main pumps |
Filters (2) | - | - | Full-flow filters (20 μm) for complete return circuit |
Filters (3) | - | - | Pressure filters (16 μm) for servo circuit |
Filters (4) | - | - | Full-flow filters (6 μm) for engine cooling return circuit |
Filters (5) | - | - | Swing charge filter (15 μm) |
Filters (6) | - | - | Pump case return screens (125 μm) |
Backhoe Attachment (BH) - Backhoe |
|||
Capacity 1:1 | - | - | 10.6 yd³ |
Total Width | - | - | 8.8 ft |
Number of Teeth | - | - | 5 |
Tooth System | - | - | Cat C70 or M75 |
Weight - Including Standard Wear Package | - | - | 18521 lb |
Maximum Material Density - Loose | - | - | 3030 lb/yd³ |