Compare Equipment Go Back
 6020B Hydraulic Shovel |
 6060 Hydraulic Mining Shovel |
|
|
General |
|||
|---|---|---|---|
| Engine Output - SAE J1995 | 1040 HP | 3015 HP | - |
| Bucket Payload | 23.8 ton (US) | 67 ton (US) | - |
| Operating Weight | 253.8 ton (US) | 660 ton (US) | - |
| Note | Specifications shown above apply to a Backhoe configuration. A frontless configuration is also available. | Specifications shown above apply to Face Shovel configuration. Backhoe and Frontless configurations are also available. | - |
| Standard Bucket Capacity | 15.7 yd³ | - | - |
Electrical System |
|||
| Batteries (12V each) - In Series/Parallel Installation | 630 Ah – 24V | - | - |
| Components (3) | 9 LED high-brightness working flood lights: – 7 for working area – 2 for rear end |
Lockable starter isolator switch | - |
| Batteries (12V each) | 6 × 210 Ah | - | - |
| Components (1) | Emergency stop buttons inside cab, accessible from all seating locations, and engine module | 6 maintenance-free batteries | - |
| Components (2) | Additional ground-level emergency stop | Lockable battery isolator switch | - |
| System Voltage | 24V | 24 V | - |
| Battery Isolation Relays | manual lockable disconnect switch and automatic disconnect relay | - | - |
| Components (6) | 1 beacon lamp on cab roof | 2 electric horns (1 cab module; 1 oil cooler module) | - |
| Components (5) | 7 LED service lights | 17 LED service lights | - |
| Components (4) | 2 LED high-brightness access flood lights | 13 LED high-brightness working flood lights | - |
| Batteries in Series/Parallel Installation | - | 6 x 210 Ah; 12 V each; 630 Ah 24 V in total | - |
Hydraulic Oil Cooling |
|||
| Features (2) | Variable electronically controlled flow of oil through cooler and fan speed | Fan speed and flow of oil to the coolers are thermostatically controlled | - |
| Oil Flow of Cooling Pumps | 211 gal/min | 4 x 488 L/min (4 x 129 gal/min) | - |
| Diameter - Fan | 4.92 ft | 46 in | - |
| Features (1) | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running | - |
| Features (3) | Superior cooling efficiency to ensure optimum oil temperature | Extremely high cooling efficiency to ensure optimum oil temperature | - |
| Components | - | 4 cooling fans | - |
| Features (4) | - | Gear-type cooling pumps supplying high-volume, low-pressure oil to fans and aluminum coolers | - |
Operator's Cab |
|||
| Components (5) | Full sized trainer seat with safety belt and work table | Operator Protective Guard (Top Guard) (ISO 10262:1998) | - |
| Internal Dimensions of Cab - Width | 5.33 ft | 5.33 ft | - |
| Components (7) | Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant | Additional fold-away auxiliary seat with safety belt | - |
| Components (9) | Roller blinds | Monitoring system with 254 mm (10 in) touch screen | - |
| Components (11) | Additional emergency ladder in close proximity to emergency escape window | Emergency egress ladder | - |
| Internal Dimensions of Cab - Length | 7.32 ft | 7.33 ft | - |
| Components (8) | Windshield with parallel intermittent wiper/washer | Operator Presence switch | - |
| Components (2) | Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests | In-floor window with removable grate | - |
| New BCS Features (1) | Robust instrument panel including large (254 mm/10 in) color touch screen | - | - |
| New BCS Features (3) | Graphical data logging | - | - |
| New BCS Features (4) | Fault memory capabilities | - | - |
| Operator's Eye Level (approximate) | 18.04 ft | - | - |
| New BCS Features (2) | On-screen troubleshooting assistance | - | - |
| Components (10) | Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated | Powered 45 degree access stairway | - |
| New BCS Features (5) | USB, Lan (TCP/IP) and CAN BUS interfaces for data export | - | - |
| Components (3) | Safety switch in operator's seat for automatic motion shutdown | Pneumatically cushioned and multi-adjustable comfort seat with heating, cooling, and lumbar support | - |
| Internal Dimensions of Cab - Height | 6.79 ft | 6.75 ft | - |
| Components (1) | Large cab floor window with removable grating for easy cleaning | Single hydraulically driven HVAC System, with dual system option | - |
| Components (4) | Joystick integrated in adjustable seat armrest | Independently adjustable seat consoles with integrated joysticks | - |
| New Board Control System (BCS) Features: | Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system | - | - |
| Components (6) | Auxiliary fold-away seat with safety belt for 3rd person | Elevated full-size trainer seat with safety belt and laptop desk | - |
| Operator's Eye Level - Approximately | - | 24.91 ft | - |
| Components (12) | - | FM/AM radio with USB and AUX input | - |
| Components (13) | - | Roller blinds on 3 front windows | - |
| Components (14) | - | 3 cup holders | - |
| Components (15) | - | Cat Electronic Technician service port | - |
Swing System |
|||
| Swing Ring | Triple-race roller bearing with sealed internal gearing | Triple-race roller bearing with sealed internal gearing | - |
| Maximum Swing Speed | 4.9 r/min | 3.8 r/min | - |
| Swing Drive | 2 compact planetary transmissions with axial piston motors | 4 compact planetary transmissions with axial piston motors | - |
| Parking Brake | Wet multiple-disc brake, spring-loaded/hydraulically released | - | - |
| Features (2) | All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system | Closed-loop swing circuit with torque control | - |
| Features (1) | Open swing circuit with auto slow down when joysticks in neutral | Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody | - |
| Parking Brakes | - | Wet multiple disc brake, spring loaded/hydraulically released | - |
| Features (3) | - | Hydraulic braking of the swing motion by counteracting control | - |
| Features (4) | - | All raceways and the internal gearing of swing ring, supplied by automatic central lubrication system | - |
Undercarriage |
|||
| Track Pads - Each Side | 45 | 42 | - |
| Components (1) | Forged double-grouser track pads | HD tracks with cast double-grouser track pad | - |
| Components (6) | Audible travel alarm | Automatic hydraulic retarder valve to prevent over-speed on downhill travel | - |
| Bottom Rollers - Each Side | 8 | 7 | - |
| Travel Speed - 1st Stage - Maximum | 0.68 mile/h | 0.68 mile/h | - |
| Components (4) | Fully hydraulic self-adjusting track tensioning system with accumulator | Acoustic travel alarm (forward and reverse) | - |
| Components (5) | Automatic hydraulic retarder valve to prevent overspeed on downhill travel | Fully hydraulic, self-adjusting track tensioning system with piston accumulator | - |
| Parking Brakes | Wet multiple disc brake, spring loaded/hydraulically released | - | - |
| Travel Speed - 2nd Stage - Maximum | 1.49 mile/h | 0.99 mile/h | - |
| Gradeability - Travel Drives | Approximately 54% | - | - |
| Components (3) | All running surfaces of sprockets, idlers, rollers and track chain links hardened | Hardened running surfaces of sprockets, idlers, rollers, pad links, and teeth contact areas | - |
| Maximum Tractive Force | 265860 lbf | 661160 lb | - |
| Travel Drives - Each Side | 1 planetary transmission with 2 two-stage axial piston motors | 1 planetary transmission with 2 two-stage axial piston motors | - |
| Components (2) | Chain links connected by hardened pins and bushings | HD fixed axle rollers and idlers | - |
| Support Rollers - Each Side | 3 | 2 plus a skid plate in between | - |
| Gradeability - Travel Drives - Maximum | - | 39 % | - |
Automatic Lubrication System |
|||
| Type (3) | System condition and failures displayed by Board Control System | Grease filters (200 µm) between service station and container as well as directly behind grease pump | - |
| Capacity - Grease Barrel | 54 gal (US) | - | - |
| Type (1) | Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control | Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control to adjust the pause/lube times | - |
| Type (2) | Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing | System failures displayed by monitoring system | - |
| Capacity - Grease Container | - | 188 gal (US) | - |
| Type (4) | - | Main lube system connections include: pivot points of attachment, bucket and cylinders, raceways of swing roller bearing, and 2 greasing pinions for the internal gearing of swing ring | - |
Attachment |
|||
| Type (5) | Float valve for boom down function | - | - |
| Type (2) | High-tensile steel with solid steel castings at pivot areas | - | - |
| Type (3) | Boom and stick stress-relieved after welding | - | - |
| Type (1) | Boom and stick torsion-resistant with welded box design | - | - |
| Type (4) | Catwalks with rails at boom | - | - |
| Buckets Equipped With | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
- | - |
Operating Weights - Backhoe |
|||
| Standard Track Pads | 2.62 ft | - | - |
| Operating Weight | 507500 lb | - | - |
| Ground Pressure | 31.9 psi | - | - |
Hydraulic System with Electronic Pump Management |
|||
| Maximum Swing Oil Flow | 216 gal/min | - | - |
| Maximum Pressure - Attachment | 4495 psi | - | - |
| Filters (4) | Pressure filters (6 μm) for servo circuit | - | - |
| Electronic Pump Management Contains (3) | Automatic return of main pumps to zero flow | - | - |
| Features (2) | Cooling of pump transmission gear oil | - | - |
| Maximum Pressure - Travel | 4495 psi | - | - |
| Maximum Pressure - Swing - Acceleration | 4495 psi | - | - |
| Filters (3) | Full-flow filters (10 μm) for cooling return circuit | - | - |
| Electronic Pump Management Contains (2) | Dedicated circuit pump allocation | - | - |
| Maximum Total Oil Flow | 621 gal/min | - | - |
| Filters (2) | Full-flow filters (10 μm) for complete return circuit | - | - |
| Main Pumps | 6 × variable swash plate pumps | - | - |
| Filters (1) | Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump | - | - |
| Electronic Pump Management Contains (4) | Automatic rpm reduction of engine speed during working breaks | - | - |
| Filters (5) | Transmission oil filter (40 μm) | - | - |
| Electronic Pump Management Contains (5) | Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature | - | - |
| Electronic Pump Management Contains (1) | Electronic load limit control | - | - |
| Features (1) | Pressure cut-off function for all main pumps | - | - |
| Total Volume of Hydraulic Oil | 925 gal (US) | - | - |
| Hydraulic Tank Capacity | 740 gal (US) | - | - |
| Maximum Pressure - Swing - Deceleration | 5080 psi | - | - |
Centralized Service Area |
|||
| Equipped With (3) | Indicator light for hydraulic tank full | - | - |
| Equipped With (1) | Quick couplings for: – Diesel fuel – Engine coolant – Pump transmission gear oil – Engine oil (oil pan) – Hydraulic oil |
- | - |
| Features | Centralized service area accessible from ground level. | - | - |
| Equipped With (2) | Cat jump-start socket | - | - |
Digging Forces |
|||
| Maximum Tearout Force | 146125 lb | - | - |
| Maximum Breakout Force | 164050 lb | 388780 lb | - |
| Maximum Crowd Force | - | 494410 lb | - |
Working Ranges |
|||
| Maximum Digging Reach | 52.17 ft | 54.17 ft | - |
| Maximum Digging Depth | 26.57 ft | 9.17 ft | - |
| Maximum Digging Height | 45.6 ft | 51.17 ft | - |
Operating Specifications |
|||
| Operating Weight | 254 ton (US) | - | - |
| Bucket Payload | 24 Sh Ton | - | - |
Bucket |
|||
| Standard Bucket Capacity - Backhoe (Heaped 1:1) | 15.7 yd³ | - | - |
Engine - Equivalent to U.S. EPA Tier 2 |
|||
| Gross Power - SAE J1995 | 1040 HP | - | - |
| Engine Model | Cat C32 ACERT | - | - |
| Net Power - SAE J1349 | 1032 HP | - | - |
Diesel Engine - Lesser Regulated |
|||
| Gross Power - SAE J1995 | 1040 HP | 3025 HP | - |
| Net Power - ISO 9249 | 1037 HP | 2990 HP | - |
| Net Power - SAE J1349 | 1032 HP | 2821 HP | - |
| Emissions | Meets China Nonroad Stage III emissions standards, equivalent to Tier 2 | Optimized for fuel consumption. | - |
Diesel Engine - Tier 4 Final |
|||
| Components (1) | Cat NOx reduction system | - | - |
| Components (7) | Two-stage fuel filter | - | - |
| Components (3) | MEUI™-C fuel system | - | - |
| Alternator | 275A | - | - |
| Bore | 5.71 in | - | - |
| Components (4) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
| No. of Cylinders | 12 | - | - |
| Displacement | 1959 in³ | - | - |
| Fuel Tank Capacity | 951 gal (US) | - | - |
| Components (5) | Micro processed engine management | - | - |
| Rated Speed | 1,800 min-1 (1,800 rpm) | - | - |
| Aspiration | Turbocharged and air-to-air aftercooled | - | - |
| Components (2) | Dual Diesel Oxidation Catalysts (DOCs) | - | - |
| Components (8) | Additional high-capacity water separator including electric priming pump | - | - |
| Components (9) | Large fuel tank allows for 24 hour machine operation | - | - |
| Components (6) | Heavy-duty air filters | - | - |
| Maximum Altitude without Deration | 2925 m (9,600 ft) – above sea level (a.s.l.) | - | - |
| Stroke | 6.38 in | - | - |
| Make and Model | Cat C32 ACERT | - | - |
Diesel Engine - Equivalent to Tier 2 |
|||
| Components (3) | Heavy-duty air filters | - | - |
| Components (4) | Two-stage fuel filter | - | - |
| Fuel Tank Capacity | 951 gal (US) | - | - |
| No. of Cylinders | 12 | - | - |
| Components (2) | Micro processed engine management | - | - |
| Displacement | 1959 in³ | - | - |
| Maximum Altitude without Deration | 3622 m (11,884 ft) – above sea level (a.s.l.) | - | - |
| Bore | 5.71 in | - | - |
| Components (1) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
| Stroke | 6.38 in | - | - |
| Aspiration | Turbocharged and air-to-air aftercooled | - | - |
| Components (5) | Additional high-capacity water separator including electric priming pump | - | - |
| Rated Speed | 1800 min-1 (1,800 rpm) | - | - |
| Alternator | 275A | - | - |
| Make and Model | Cat C32 ACERT | - | - |
| Components (6) | Large fuel tank allows for 24 hour machine operation | - | - |
Diesel Engine - Highly Regulated |
|||
| Gross Power - SAE J1995 | 1033 HP | 3015 HP | - |
| Net Power - ISO 9249 | 1024 HP | 2979 HP | - |
| Net Power - SAE J1349 | 1019 HP | 2810 HP | - |
| Emissions | Meets Tier 4 Final and Stage V emissions standards | Meets U.S. EPA Tier 4 Final emission requirements. These engines participate in the U.S. EPA averaging, banking, and trading provisions. | - |
Engine - U.S. EPA Tier 4 Final |
|||
| Net Power - SAE J1349 | 1019 HP | - | - |
| Gross Power - SAE J1995 | 1033 HP | - | - |
| Engine Model | Cat® C32 ACERT™ | - | - |
Engine |
|||
| Engine Model | - | 2 x Cat 3512E | - |
Diesel Engines |
|||
| Rated Speed | - | 1,800 min-1 (1,800 rpm) | - |
| Number of Cylinders - Each Engine | - | 12 | - |
| Bore | - | 6.69 in | - |
| Stroke | - | 8.46 in | - |
| Displacement | - | 3574 in³ | - |
| Aspiration | - | Turbocharged and charge air-cooled | - |
| Components (1) | - | Non-DEF Aftertreatment system with Diesel Oxidation Catalysts (DOCs) | - |
| Components (2) | - | High-capacity water separator | - |
| Components (3) | - | Two-stage fuel filter with series filtration | - |
| Components (4) | - | Heavy-duty air filters | - |
| Components (5) | - | Microprocessed engine management | - |
| Components (6) | - | Hydraulically driven radiator fan with electronically controlled fan speed | - |
| Components (7) | - | Exhaust manifold and turbo heat shields | - |
Operating Weights |
|||
| 6060 FS - Standard Track Pads | - | 4.58 ft | - |
| 6060 FS - Operating Weight | - | 1320110 lb | - |
| 6060 FS - Ground Pressure | - | 26.6 N/cm2 (38.5 psi) | - |
| Backhoe - Standard Track Pads | - | 4.58 ft | - |
| Backhoe - Operating Weight | - | 1323860 lb | - |
| Backhoe - Ground Pressure | - | 26.7 N/cm2 (38.7 psi) | - |
| Note | - | Operating weights include: base machine, front attachment, standard track pads, standard rock bucket, 100% fuel and lubricants. | - |
Service Refill Capacities |
|||
| Fuel Tank | - | 3136 gal (US) | - |
| Hydraulic Tank | - | 1876 gal (US) | - |
| Hydraulic System - Including Tank | - | 2483 gal (US) | - |
| Engine Oil | - | 86.6 gal (US) | - |
| Cooling System | - | 211.4 gal (US) | - |
| Swing Drive | - | 42.4 gal (US) | - |
| Grease Tank | - | 188 gal (US) | - |
Hydraulic System with Pump Managing System |
|||
| Main Pumps - Diesel Version | - | 8 variable swash plate pumps | - |
| Main Pumps - Maximum Oil Flow - Diesel Version | - | 8 x 650 L/min (8 x 172 gal/min) | - |
| Maximum Pressure - Attachment | - | 4640 psi | - |
| Maximum Pressure - Travel | - | 5220 psi | - |
| Swing Pumps - Diesel Version | - | 4 reversible swash plate pumps | - |
| Swing Pumps - Maximum Oil Flow - Diesel Version | - | 4 x 352 L/min (4 x 93 gal/min) | - |
| Maximum Pressure - Swing Pumps | - | 5075 psi | - |
Attachments |
|||
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (1) | - | Automatic roll-back limiter to prevent material spillage; Kinematic assistance to hydraulic forces | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (2) | - | Horizontal Automatic constant-angle bucket guidance; Vertical Automatic constant-angle bucket guidance | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (3) | - | Constant boom momentum throughout the entire lift arc; Crowd force assistance | - |
| All buckets (FS and BH) are equipped with a wear package consisting of: (1) | - | Special liner material covering main wear areas inside and outside of bucket and lip shrouds between teeth | - |
| All buckets (FS and BH) are equipped with a wear package consisting of: (2) | - | Wing shrouds on side walls and heel shrouds at bottom edges | - |
| Type (1) | - | Catwalks with rails at booms (FS and BH) | - |
| Type (2) | - | Guards for shovel cylinders (FS) | - |
| Type (3) | - | Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve | - |
| Type (4) | - | Service access holes from both sides of boom (FS and BH) and stick (FS) | - |
| Type (5) | - | Welding procedures allow for internal counter-welding (double prep weld) wherever possible | - |
| Type (6) | - | Booms and sticks are stress-relieved after welding | - |
| Type (7) | - | Booms and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel castings at pivot areas | - |
| Type (8) | - | Special wear packages for highly abrasive materials available upon request | - |
Standard Bucket Capacity |
|||
| Face Shovel (heaped 2:1) | - | 44.5 yd³ | - |
| Backhoe (heaped 1:1) | - | 44.5 yd³ | - |
Backhoe Attachment (BH) - Digging Forces |
|||
| Stick Digging Force - ISO | - | 295740 lb | - |
| Bucket Digging Force - ISO | - | 274840 lb | - |
Backhoe Attachment (BH) - Working Range |
|||
| Maximum Digging Height | - | 52.83 ft | - |
| Maximum Digging Reach | - | 62.33 ft | - |
| Maximum Digging Depth | - | 29.17 ft | - |
Retractable Service Station |
|||
| Installation | - | Retractable service station installed underneath the engine module and easily accessible from ground. | - |
| Equipped With (1) | - | Quick couplings for: Diesel fuel, Engine coolant - left/right engine, Pump transmission gear oil - left/right engine, Engine oil - left/right engine, Hydraulic oil tank, and grease container | - |
| Equipped With (2) | - | Cat jump-start socket | - |
| Equipped With (3) | - | Indicator lights | - |
