Compare Equipment Go Back
 6020B Hydraulic Shovel |
 6015 Hydraulic Shovel |
|
|
General |
|||
|---|---|---|---|
| Engine Output - SAE J1995 | 1040 HP | 824 HP | - |
| Bucket Payload | 23.8 ton (US) | 16.1 ton (US) | - |
| Operating Weight | 253.8 ton (US) | 154.3 ton (US) | - |
| Note | Specifications shown above apply to a Backhoe configuration. A frontless configuration is also available. | Specifications shown above apply to highly regulated, backhoe configuration. Lesser regulated and frontless configurations are also available. | - |
| Standard Bucket Capacity | 15.7 yd³ | - | - |
Electrical System |
|||
| Batteries (12V each) - In Series/Parallel Installation | 630 Ah – 24V | - | - |
| Components (3) | 9 LED high-brightness working flood lights: – 7 for working area – 2 for rear end |
Lockable battery isolation switch | - |
| Batteries (12V each) | 6 × 210 Ah | - | - |
| Components (1) | Emergency stop buttons inside cab, accessible from all seating locations, and engine module | Emergency stop in cabin, engine module, pump room and on service station accessible from ground level | - |
| Components (2) | Additional ground-level emergency stop | Four maintenance free batteries | - |
| System Voltage | 24V | 24 V | - |
| Battery Isolation Relays | manual lockable disconnect switch and automatic disconnect relay | - | - |
| Components (6) | 1 beacon lamp on cab roof | 2 electric horns | - |
| Components (5) | 7 LED service lights | 14 LED high-brightness working lights | - |
| Components (4) | 2 LED high-brightness access flood lights | 5 LED service lights | - |
| Batteries | - | 4 × 200 Ah (12 V each) | - |
| Alternator Rating | - | 150 A (24 V) in total | - |
| Components (7) | - | Two (2) lights for rear end | - |
| Components (9) | - | One (1) beacon light on cabin roof | - |
| Components (8) | - | One (1) light for machine deck/service | - |
Hydraulic Oil Cooling |
|||
| Features (2) | Variable electronically controlled flow of oil through cooler and fan speed | - | - |
| Oil Flow of Cooling Pumps | 211 gal/min | - | - |
| Diameter - Fan | 4.92 ft | - | - |
| Features (1) | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running | - | - |
| Features (3) | Superior cooling efficiency to ensure optimum oil temperature | - | - |
Operator's Cab |
|||
| Components (5) | Full sized trainer seat with safety belt and work table | Removable lower windshield with in cab storage bracket | - |
| Internal Dimensions of Cab - Width | 5.33 ft | - | - |
| Components (7) | Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant | Beverage holder | - |
| Components (9) | Roller blinds | AM/FM radio | - |
| Components (11) | Additional emergency ladder in close proximity to emergency escape window | Two stereo speakers | - |
| Internal Dimensions of Cab - Length | 7.32 ft | - | - |
| Components (8) | Windshield with parallel intermittent wiper/washer | Literature holder | - |
| Components (2) | Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests | Heated cab mirror | - |
| New BCS Features (1) | Robust instrument panel including large (254 mm/10 in) color touch screen | - | - |
| New BCS Features (3) | Graphical data logging | - | - |
| New BCS Features (4) | Fault memory capabilities | - | - |
| Operator's Eye Level (approximate) | 18.04 ft | - | - |
| New BCS Features (2) | On-screen troubleshooting assistance | - | - |
| Components (10) | Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated | Radio with MP3 auxiliary audio port | - |
| New BCS Features (5) | USB, Lan (TCP/IP) and CAN BUS interfaces for data export | - | - |
| Components (3) | Safety switch in operator's seat for automatic motion shutdown | Sliding upper door window (left-hand cab door) | - |
| Internal Dimensions of Cab - Height | 6.79 ft | - | - |
| Components (1) | Large cab floor window with removable grating for easy cleaning | Pressurized operator station with positive filtration | - |
| Components (4) | Joystick integrated in adjustable seat armrest | Glass-breaking safety hammer | - |
| New Board Control System (BCS) Features: | Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system | - | - |
| Components (6) | Auxiliary fold-away seat with safety belt for 3rd person | Joystick Controls Alternate Patterns including ISO/JIS, BHL, MHI, KOBE, or SCM | - |
| Components (12) | - | Storage shelf suitable for lunch or toolbox | - |
| Components (13) | - | Color LCD display with warning, filter/fluid change, and working hour information | - |
| Components (14) | - | Adjustable armrest | - |
| Components (15) | - | Height-adjustable joystick consoles | - |
| Components (16) | - | Neutral lever (lock out) for all controls | - |
| Components (17) | - | Travel control pedals with removable hand levers | - |
| Components (18) | - | Two power outlets, 10 amp (total) | - |
| Components (19) | - | Laminated glass front upper window and tempered other windows | - |
Swing System |
|||
| Swing Ring | Triple-race roller bearing with sealed internal gearing | Cross roller bearing with sealed internal gearing | - |
| Maximum Swing Speed | 4.9 r/min | 4.9 r/min | - |
| Swing Drive | 2 compact planetary transmissions with axial piston motors | Two (2) compact planetary transmissions with axial piston motors | - |
| Parking Brake | Wet multiple-disc brake, spring-loaded/hydraulically released | Wet multiple disc brake, spring-loaded/hydraulically released | - |
| Features (2) | All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system | Hydraulic braking of swing motion when control is returned to neutral position or by counteracting control for stronger braking | - |
| Features (1) | Open swing circuit with auto slow down when joysticks in neutral | Closed-loop swing circuit with speed control | - |
| Features (3) | - | All raceways and the internal gearing of swing ring supplied by automatic central lubrication system | - |
Undercarriage |
|||
| Track Pads - Each Side | 45 | - | - |
| Components (1) | Forged double-grouser track pads | Forged double-grouser track pads | - |
| Components (6) | Audible travel alarm | Automatic hydraulic retarder valve to prevent overspeed on downhill travel | - |
| Bottom Rollers - Each Side | 8 | - | - |
| Travel Speed - 1st Stage - Maximum | 0.68 mile/h | - | - |
| Components (4) | Fully hydraulic self-adjusting track tensioning system with accumulator | All running surfaces of sprockets, idlers, rollers and track chain links hardened | - |
| Components (5) | Automatic hydraulic retarder valve to prevent overspeed on downhill travel | Fully hydraulic self-adjusting track tensioning system with accumulator | - |
| Parking Brakes | Wet multiple disc brake, spring loaded/hydraulically released | - | - |
| Travel Speed - 2nd Stage - Maximum | 1.49 mile/h | - | - |
| Gradeability - Travel Drives | Approximately 54% | 38°/78% (SAE J1309) | - |
| Components (3) | All running surfaces of sprockets, idlers, rollers and track chain links hardened | Postive Pin Retention (PPR2) sealed and greased track design | - |
| Maximum Tractive Force | 265860 lbf | 197157 lbf | - |
| Travel Drives - Each Side | 1 planetary transmission with 2 two-stage axial piston motors | - | - |
| Components (2) | Chain links connected by hardened pins and bushings | Chain links connected by hardened pins and bushings | - |
| Support Rollers - Each Side | 3 | - | - |
| Travel Speed - Two Stages - 1st Stage - Maximum | - | 1.6 mile/h | - |
| Travel Speed - Two Stages - 2nd Stage - Maximum | - | 2.3 mile/h | - |
| Maximum Drawbar Pull - Forward | - | 192886 lbf | - |
| Maximum Drawbar Pull - Reverse | - | 220987 lbf | - |
| Hydraulic Track Tensioning | - | With accumulator | - |
| Number of Shoes - Each Side | - | 46 | - |
| Number of Track Rollers - Each Side | - | 9 | - |
| Number of Carrier Rollers - Each Side | - | 3 | - |
| Components (7) | - | Audible travel alarm | - |
Automatic Lubrication System |
|||
| Type (3) | System condition and failures displayed by Board Control System | Standard grease reel on machine for bucket linkage | - |
| Capacity - Grease Barrel | 54 gal (US) | 18 gal (US) | - |
| Type (1) | Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control | Central bank lubrication system | - |
| Type (2) | Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing | Grease is automatically applied to all attachment pivot points (except bucket linkage) and slew bearing | - |
| Type (4) | - | Grease refill service point accessible from ground | - |
Attachment |
|||
| Type (5) | Float valve for boom down function | - | - |
| Type (2) | High-tensile steel with solid steel castings at pivot areas | - | - |
| Type (3) | Boom and stick stress-relieved after welding | - | - |
| Type (1) | Boom and stick torsion-resistant with welded box design | - | - |
| Type (4) | Catwalks with rails at boom | - | - |
| Buckets Equipped With | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
- | - |
Operating Weights - Backhoe |
|||
| Standard Track Pads | 2.62 ft | - | - |
| Operating Weight | 507500 lb | 154 ton (US) | - |
| Ground Pressure | 31.9 psi | - | - |
Hydraulic System with Electronic Pump Management |
|||
| Maximum Swing Oil Flow | 216 gal/min | - | - |
| Maximum Pressure - Attachment | 4495 psi | - | - |
| Filters (4) | Pressure filters (6 μm) for servo circuit | - | - |
| Electronic Pump Management Contains (3) | Automatic return of main pumps to zero flow | - | - |
| Features (2) | Cooling of pump transmission gear oil | - | - |
| Maximum Pressure - Travel | 4495 psi | - | - |
| Maximum Pressure - Swing - Acceleration | 4495 psi | - | - |
| Filters (3) | Full-flow filters (10 μm) for cooling return circuit | - | - |
| Electronic Pump Management Contains (2) | Dedicated circuit pump allocation | - | - |
| Maximum Total Oil Flow | 621 gal/min | - | - |
| Filters (2) | Full-flow filters (10 μm) for complete return circuit | - | - |
| Main Pumps | 6 × variable swash plate pumps | - | - |
| Filters (1) | Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump | - | - |
| Electronic Pump Management Contains (4) | Automatic rpm reduction of engine speed during working breaks | - | - |
| Filters (5) | Transmission oil filter (40 μm) | - | - |
| Electronic Pump Management Contains (5) | Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature | - | - |
| Electronic Pump Management Contains (1) | Electronic load limit control | - | - |
| Features (1) | Pressure cut-off function for all main pumps | - | - |
| Total Volume of Hydraulic Oil | 925 gal (US) | - | - |
| Hydraulic Tank Capacity | 740 gal (US) | - | - |
| Maximum Pressure - Swing - Deceleration | 5080 psi | - | - |
Centralized Service Area |
|||
| Equipped With (3) | Indicator light for hydraulic tank full | - | - |
| Equipped With (1) | Quick couplings for: – Diesel fuel – Engine coolant – Pump transmission gear oil – Engine oil (oil pan) – Hydraulic oil |
Emergency stop | - |
| Features | Centralized service area accessible from ground level. | - | - |
| Equipped With (2) | Cat jump-start socket | Quick couplings for: Diesel fuel and Grease | - |
| Feature | - | Accessible from ground level | - |
Digging Forces |
|||
| Maximum Tearout Force | 146125 lb | - | - |
| Maximum Breakout Force | 164050 lb | - | - |
Working Ranges |
|||
| Maximum Digging Reach | 52.17 ft | - | - |
| Maximum Digging Depth | 26.57 ft | - | - |
| Maximum Digging Height | 45.6 ft | - | - |
Operating Specifications |
|||
| Operating Weight | 254 ton (US) | - | - |
| Bucket Payload | 24 Sh Ton | - | - |
Bucket |
|||
| Standard Bucket Capacity - Backhoe (Heaped 1:1) | 15.7 yd³ | - | - |
Engine - Equivalent to U.S. EPA Tier 2 |
|||
| Gross Power - SAE J1995 | 1040 HP | 839 HP | - |
| Engine Model | Cat C32 ACERT | Cat® C27 | - |
| Net Power - SAE J1349 | 1032 HP | 746 HP | - |
Diesel Engine - Lesser Regulated |
|||
| Gross Power - SAE J1995 | 1040 HP | - | - |
| Net Power - ISO 9249 | 1037 HP | - | - |
| Net Power - SAE J1349 | 1032 HP | - | - |
| Emissions | Meets China Nonroad Stage III emissions standards, equivalent to Tier 2 | - | - |
Diesel Engine - Tier 4 Final |
|||
| Components (1) | Cat NOx reduction system | - | - |
| Components (7) | Two-stage fuel filter | - | - |
| Components (3) | MEUI™-C fuel system | - | - |
| Alternator | 275A | - | - |
| Bore | 5.71 in | - | - |
| Components (4) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
| No. of Cylinders | 12 | - | - |
| Displacement | 1959 in³ | - | - |
| Fuel Tank Capacity | 951 gal (US) | - | - |
| Components (5) | Micro processed engine management | - | - |
| Rated Speed | 1,800 min-1 (1,800 rpm) | - | - |
| Aspiration | Turbocharged and air-to-air aftercooled | - | - |
| Components (2) | Dual Diesel Oxidation Catalysts (DOCs) | - | - |
| Components (8) | Additional high-capacity water separator including electric priming pump | - | - |
| Components (9) | Large fuel tank allows for 24 hour machine operation | - | - |
| Components (6) | Heavy-duty air filters | - | - |
| Maximum Altitude without Deration | 2925 m (9,600 ft) – above sea level (a.s.l.) | - | - |
| Stroke | 6.38 in | - | - |
| Make and Model | Cat C32 ACERT | - | - |
Diesel Engine - Equivalent to Tier 2 |
|||
| Components (3) | Heavy-duty air filters | - | - |
| Components (4) | Two-stage fuel filter | - | - |
| Fuel Tank Capacity | 951 gal (US) | - | - |
| No. of Cylinders | 12 | - | - |
| Components (2) | Micro processed engine management | - | - |
| Displacement | 1959 in³ | - | - |
| Maximum Altitude without Deration | 3622 m (11,884 ft) – above sea level (a.s.l.) | - | - |
| Bore | 5.71 in | - | - |
| Components (1) | Hydraulically driven radiator fan with variable electronically controlled fan speed | - | - |
| Stroke | 6.38 in | - | - |
| Aspiration | Turbocharged and air-to-air aftercooled | - | - |
| Components (5) | Additional high-capacity water separator including electric priming pump | - | - |
| Rated Speed | 1800 min-1 (1,800 rpm) | - | - |
| Alternator | 275A | - | - |
| Make and Model | Cat C32 ACERT | - | - |
| Components (6) | Large fuel tank allows for 24 hour machine operation | - | - |
Diesel Engine - Highly Regulated |
|||
| Gross Power - SAE J1995 | 1033 HP | - | - |
| Net Power - ISO 9249 | 1024 HP | - | - |
| Net Power - SAE J1349 | 1019 HP | - | - |
| Emissions | Meets Tier 4 Final and Stage V emissions standards | - | - |
Engine - U.S. EPA Tier 4 Final |
|||
| Net Power - SAE J1349 | 1019 HP | 746 HP | - |
| Gross Power - SAE J1995 | 1033 HP | 824 HP | - |
| Engine Model | Cat® C32 ACERT™ | Cat® C27 | - |
Engine - Cat C27 with Tier 4 Final Emission Standards |
|||
| Number of Cylinders | - | 12 | - |
| Bore | - | 5.4 in | - |
| Stroke | - | 6 in | - |
| Displacement | - | 1648 in³ | - |
Engine - Cat C27 with Tier 1 or Tier 2 Equivalent Emission Standards |
|||
| Number of Cylinders | - | 12 | - |
| Bore | - | 5.4 in | - |
| Stroke | - | 6 in | - |
| Displacement | - | 1648 in³ | - |
| Aspiration | - | Turbocharged and air-to-air aftercooled | - |
Weights |
|||
| Ground Pressure | - | 23.6 psi | - |
| Note | - | Operating weight includes: 700 mm (28 in) track shoes, 7.6 m (24 ft 11 in) boom, 3.4 m (11 ft 2 in) stick, standard rock bucket, 100% fuel and lubricants | - |
| Operating Weight | - | 308000 lb | - |
Track |
|||
| Standard | - | 28 in | - |
| Wide | - | 36 in | - |
| Extra Wide | - | 39 in | - |
| Number of Shoes - Each Side | - | 46 | - |
| Number of Track Rollers - Each Side | - | 9 | - |
| Number of Carrier Rollers - Each Side | - | 3 | - |
| Track Pads | - | Double grouser | - |
Drive |
|||
| Travel Speed - Two Stages - 1st Stage - Maximum | - | 1.4 mile/h | - |
| Travel Speed - Two Stages - 2nd Stage - Maximum | - | 2.1 mile/h | - |
| Maximum Drawbar Pull - Forward | - | 192886 lbf | - |
| Maximum Drawbar Pull - Reverse | - | 220987 lbf | - |
| Gradeability - Travel Drives | - | Approximately 42% | - |
| Hydraulic Track Tensioning | - | With accumulator | - |
| Maximum Drawbar Pull | - | 179847 lbf | - |
Service Refill Capacities |
|||
| Fuel Tank | - | 449 gal (US) | - |
| Cooling System | - | 44 gal (US) | - |
| Engine Oil | - | 23 gal (US) | - |
| Swing Drive | - | 2.4 gal (US) | - |
| Hydraulic System - Including Tank | - | 463 gal (US) | - |
| Hydraulic Tank | - | 253 gal (US) | - |
| Grease Tank | - | 18 gal (US) | - |
Hydraulic System |
|||
| Main Pumps | - | 3 × variable swash plate pumps | - |
| Main Pumps - Maximum Total Oil Flow | - | 407 gal/min | - |
| Main Pumps - Maximum Pressure - Attachment | - | 4641 psi | - |
| Pilot Pump | - | 1 × gear pump | - |
| Pilot Pump - Maximum Flow, Pilot | - | 40.4 gal/min | - |
| Pilot Pump - Maximum Pressure, Pilot | - | 1378 psi | - |
| Main Pumps - Maximum Pressure - Travel | - | 4641 psi | - |
| Swing Pump | - | 1 × variable swash plate pump | - |
| Engine Fan Pump - Maximum Flow, Engine Fan | - | 53.1 gal/min | - |
| Engine Fan Pump - Maximum Pressure, Engine Fan | - | 3191 psi | - |
| Engine Fan Pump | - | 1 × variable swash plate pump | - |
| Hydraulic Fan Pump - Maximum Flow, Hydraulic Fan | - | 22.7 gal/min | - |
| Swing Pump - Maximum Flow - Swing | - | 127 gal/min | - |
| Hydraulic Fan Pump | - | 1 × variable swash plate pump | - |
| Hydraulic Fan Pump - Maximum Pressure, Hydraulic Fan | - | 1958 psi | - |
| Swing Pump - Maximum Pressure - Swing | - | 5294 psi | - |
| Hydraulic Oil Cooling - Maximum Flow | - | 284 gal/min | - |
| Hydraulic Oil Cooling - Diameter of Fan | - | 40 in | - |
| Filters (1) | - | Full-flow high-pressure filters (200 μm) for main pumps | - |
| Filters (2) | - | Full-flow filters (20 μm) for complete return circuit | - |
| Filters (3) | - | Pressure filters (16 μm) for servo circuit | - |
| Filters (4) | - | Full-flow filters (6 μm) for engine cooling return circuit | - |
| Filters (5) | - | Swing charge filter (15 μm) | - |
| Filters (6) | - | Pump case return screens (125 μm) | - |
Engine |
|||
| Emissions | - | U.S. EPA Tier 4 Final and EU Stage V; China Nonroad Stage III, equivalent to U.S. EPA Tier 2; Equivalent to U.S. EPA Tier 1 | - |
Attachments |
|||
| Type (1) | - | Boom and stick torsion-resistant with welded box design | - |
| Type (2) | - | High-tensile steel with solid steel castings at pivot areas | - |
| Type (3) | - | Boom and stick stress-relieved after welding | - |
| Type (4) | - | Float valve for boom down function | - |
| Buckets Equipped With | - | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds | - |
Backhoe Attachment (BH) - Working Range |
|||
| Maximum Digging Depth | - | 26.3 ft | - |
| Maximum Digging Reach | - | 45.6 ft | - |
| Maximum Digging Height | - | 41.9 ft | - |
| Maximum Dump Height | - | 27.9 ft | - |
Backhoe Attachment (BH) - Digging Forces |
|||
| Bucket Digging Force - ISO | - | 120947 lbf | - |
| Bucket Digging Force - SAE | - | 112600 lbf | - |
| Stick Digging Force - ISO | - | 104761 lbf | - |
| Stick Digging Force - SAE | - | 98800 lbf | - |
Backhoe Attachment (BH) - Backhoe |
|||
| Capacity 1:1 | - | 10.6 yd³ | - |
| Total Width | - | 8.8 ft | - |
| Number of Teeth | - | 5 | - |
| Tooth System | - | Cat C70 or M75 | - |
| Weight - Including Standard Wear Package | - | 18521 lb | - |
| Maximum Material Density - Loose | - | 3030 lb/yd³ | - |
