Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module and alternator.
-
-
Note (2)
The following engine configurations are available: – Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. – Noncertified that emits equivalent to U.S. EPA Tier 3.
-
-
Operating Specifications
Operating Weight
105271 lb
-
-
Blade Capacities
7.9 – 22.2 m3 (10.3 – 29.0 yd3)
-
-
Transmission
Transmission Type
Cat planetary power shift
-
-
Forward - 1
4.2 mile/h
-
-
Forward - 2
7.2 mile/h
-
-
Forward - 3
12.6 mile/h
-
-
Forward - 4
22 mile/h
-
-
Reverse - 1
4.2 mile/h
-
-
Reverse - 2
7.6 mile/h
-
-
Reverse - 3
13.3 mile/h
-
-
Direct Drive - Forward 1
Lock-up disabled
-
-
Direct Drive - Forward 2
7.7 mile/h
-
-
Direct Drive - Forward 3
13.7 mile/h
-
-
Direct Drive - Forward 4
23.9 mile/h
-
-
Direct Drive - Reverse 1
4.5 mile/h
-
-
Direct Drive - Reverse 2
8.1 mile/h
-
-
Direct Drive - Reverse 3
14.3 mile/h
-
-
Note
Travel speeds based on 35/65-R33 tire
-
-
1.0 Forward
-
2.5 mile/h
-
1.5 Forward
-
3.4 mile/h
-
2.0 Forward
-
4.5 mile/h
-
2.5 Forward
-
6 mile/h
-
3.0 Forward
-
7.8 mile/h
-
1.0 Reverse
-
3.2 mile/h
-
1.5 Reverse
-
4.2 mile/h
-
2.0 Reverse
-
5.6 mile/h
-
2.5 Reverse
-
7.5 mile/h
-
3.0 Reverse
-
9.8 mile/h
-
Transmission Clutch Diameter
-
17 in
-
Type
-
Planetary powershift
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
Pilot operated LS valve with EH
-
-
Lift/Tilt System
Variable displacement piston
-
-
Maximum Flow at 1,900 rpm
153 gal/min
-
-
Relief Valve Setting - Lift/Tilt
4641 psi
-
-
Cylinders, Double Acting - Lift, Bore and Stroke
139.75 mm × 1021 mm (5.5 in × 40.2 in)
-
-
Cylinders, Double Acting - Left and Right Tilt, Bore and Stroke
140 mm × 230 mm (5.5 in × 9.1 in)
-
-
Pilot System
Variable displacement piston
-
-
Pilot Maximum Flow
13.7 gal/min
-
-
Pilot Relief Valve Setting
580 psi
-
-
Hydraulic System - Steering
Steering System - Circuit
Pilot, load sensing
-
-
Steering System - Pump
Piston, variable displacement
-
-
Maximum Flow
65.8 gal/min
-
-
Relief Valve Setting - Steering
3495 psi
-
-
Total Steering Angle
86 °
-
-
Steering Cycle Times - High Idle
3.1 s
-
-
Steering Cycle Times - Low Idle
5.7 s
-
-
Service Refill Capacities
Fuel Tank
209.5 gal (US)
-
-
Cooling System
31.7 gal (US)
-
-
Crankcase
15.9 gal (US)
-
-
Diesel Exhaust Fluid Tank
8.7 gal (US)
-
-
Transmission
31.7 gal (US)
-
-
Hydraulic System Factory Fill
63.4 gal (US)
-
-
Differential - Final Drives - Front
49.1 gal (US)
-
-
Differential - Final Drives - Rear
49.1 gal (US)
-
-
Hydraulic System - Tank Only
37 gal (US)
-
-
Note (1)
All non-road Tier 4 Final/Stage V diesel engines are required to use: – ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels** up to: • 20% biodiesel FAME (fatty acid methyl este
-
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system co
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.600 metric tonnes.
-
Axles
Front
Fixed
-
-
Rear
Trunnion
-
-
Oscillation Angle
±13°
-
-
Brakes
Brakes
ISO 3450: 2011
-
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
113 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
109 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
113 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
110 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Dimensions
Height - Top of Exhaust Stack
15.9 ft
-
-
Height - Top of Air Cleaner
12.8 ft
-
-
Height - Top of Hood
10.9 ft
-
-
Ground Clearance - Bumper
3.1 ft
-
-
Centerline of Rear Axle to Edge of Bumper
10.5 ft
-
-
Wheel Base
14.9 ft
-
-
Length - Front of Tire
28.4 ft
-
-
Length - Straight Blade on Ground
32.6 ft
-
-
Length - Universal Blade on Ground
34.4 ft
-
-
Centerline of Front Axle to Hitch
7.5 ft
-
-
Ground Clearance
1.7 ft
-
-
Height - Top of Cab
13.7 ft
-
-
Engine - U.S. EPA Tier 4 Final/EU Stage V
Engine Model
-
Cat® C27
-
Engine Power - Net SAE J1349/ISO 9249** - Forward
-
602 hp
-
Engine Power - Gross SAE J1995* - Forward
-
631 hp
-
Engine Power - Gross SAE J1995* - Reverse
-
801 hp
-
Engine Power - ISO 14396* - Forward
-
620 hp
-
Engine Power - ISO 14396* - Reverse
-
789 hp
-
Engine Power - Net SAE J1349/ISO 9249** - Reverse
-
756 hp
-
Displacement
-
1648 in³
-
Stroke
-
6 in
-
Bore
-
5.4 in
-
Emissions
-
U.S. EPA Tier 4 Final/EU Stage V
-
Note (1)
-
*Excludes all fan losses.
-
Note (2)
-
All Engine ratings apply at 1,800 rpm.
-
Note (3)
-
Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
-
Note (4)
-
Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
-
Note (5)
-
**Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.
-
Weights
Operating Weight
-
154888 lb
-
Shipping Weight
-
111739 lb
-
Note (1)
-
D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.
-
Note (2)
-
D10 Shipping Weight includes coolant, lubricants, 10% fuel, FOPS cab, fast fuel, and 610 mm (24 in) ES shoes.
-
Undercarriage
Shoe Type
-
Extreme Service (ES)
-
Width - Shoe
-
24 in
-
Shoes/Side
-
44
-
Grouser Height
-
3.7 in
-
Pitch
-
10.2 in
-
Ground Clearance
-
28.5 in
-
Track Gauge
-
100.4 in
-
Length - Track on Ground
-
152.8 in
-
Ground Contact Area
-
7347 in²
-
Track Rollers/Side
-
8
-
Number of Carrier Rollers
-
1 per side (optional)
-
Standards
ROPS
-
Rollover Protective Structure (ROPS) meets the following criteria: ISO 3471:2008.
-
FOPS
-
Falling Object Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 LEVEL II.
-
Sound
-
Operator Sound Pressure Level (ISO 6396:2008): 78 db(A)
-
Note
-
The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds. The measurement was conducted with the cab doors and the cab windows closed. The cab was properly installed and
-
Sound (1)
-
Exterior Sound Pressure Level (ISO 6395:2008): 116 db(A)
-
Note (1)
-
The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine
cooling fan speeds.
-
Note (2)
-
The sound levels listed above include both measurement uncertainty and uncertainty due to production variation.
-
Note (3)
-
The available sound suppression package can reduce the dynamic exterior sound power level of the machine by up to 4 db(A) and the dynamic operator sound pressure level by up to 2 db(A).
10SU ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry)
-
19.98 in
-
10SU ABR - Digging Depth - Blade Pitch: Nominal
-
25.23 in
-
10SU ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread)
-
30.08 in³
-
10SU ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry)
-
66.14 in
-
10SU ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread)
-
53.86 in
-
10SU ABR - Ground Clearance - Maximum Tilt LH
-
56.3 in
-
10SU ABR - Ground Clearance - Maximum Tilt RH
-
56.3 in
-
10U ABR - Capacity (SAE J1265)
-
28.7 yd³
-
10U ABR - Width (over end bits)
-
207.1 in
-
10U ABR - Height
-
83.5 in
-
10U ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry)
-
19.98 in
-
10U ABR - Digging Depth - Blade Pitch: Nominal
-
60 in
-
10U ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread)
-
30.1 in
-
10U ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry)
-
66.1 in
-
10U ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread)
-
53.9 in
-
10U ABR - Ground Clearance - Maximum Tilt LH
-
60.8 in
-
10U ABR - Ground Clearance - Maximum Tilt RH
-
60.8 in
-
10U ABR - Weights - Blade Weight*
-
23585 lb
-
10U ABR - Weights - Total Operating Weight** (with blade and SS ripper)
-
154888 lb
-
Note (1)
-
Maximum LH and RH tilt for 10SU ABR and 10U ABR blades: 17.31 degrees
-
Note (2)
-
*Does not include hydraulic controls but includes blade cylinders, pusharms.
-
Note (3)
-
**D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.
-
Ripper - Single Shank
Maximum penetration force * (shank vertical)
-
49233 lbf
-
Maximum penetration depth (standard tip)
-
59.2 in
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
-
36 in
-
Weight
-
14209 lb
-
Note
-
Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.
-
Ripper - Single Shank, Deep Ripping
Maximum penetration force * (shank vertical)
-
53055 lbf
-
Maximum penetration depth (standard tip)
-
78.3 in
-
Weight
-
14548 lb
-
Note
-
Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.
-
Engine - U.S. EPA Tier 2 Equivalent
Engine Model
-
Cat® C27
-
Engine Power - Net SAE J1349/ISO 9249** - Forward
-
603 hp
-
Engine Power - Net SAE J1349/ISO 9249** - Reverse
-
722 hp
-
Engine Power - Gross SAE J1995* - Forward
-
631 hp
-
Engine Power - Gross SAE J1995* - Reverse
-
766 hp
-
Engine Power - ISO 14396* - Forward
-
622 hp
-
Engine Power - ISO 14396* - Reverse
-
756 hp
-
Displacement
-
1648 in³
-
Bore
-
5.4 in
-
Stroke
-
6 in
-
Emissions
-
U.S. EPA Tier 2 Equivalent
-
Note (1)
-
*Excludes all fan losses.
-
Note (2)
-
All Engine ratings apply at 1,800 rpm.
-
Note (3)
-
Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
-
Note (4)
-
Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
-
Note (5)
-
**Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.
-
Fuel Tank Capacities
Fuel Tank - Usable Volume
-
323.3 gal (US)
-
Fuel Tank - Total Volume
-
335.2 gal (US)
-
Hydraulic Controls
Pump Type
-
Variable displacement piston
-
Pump Output - Implement
-
112 gal/min
-
Note (1)
-
Implement Pump output measured are 2,010 engine rpm and
7000 kPa (1,015 psi).
-
Fan Pump
-
21.7 gal/min
-
Note (2)
-
Fan Pump output measured at 2,010 engine rpm and 26 000 kPa (3,771 psi).
-
Tilt Cylinder Flow - Rod End Flow
-
112 gal/min
-
Tilt Cylinder Flow - Head End Flow
-
63.4 gal/min
-
Lift Cylinder Relief Valve Setting
-
4061.1 psi
-
Tilt Cylinder Relief Valve Setting
-
3872.5 psi
-
Ripper - Lift - Relief Valve Setting
-
4061.1 psi
-
Ripper - Pitch - Relief Valve Setting
-
4061.1 psi
-
Tank Capacity
-
32.2 gal (US)
-
Cylinder Sizing - Blade Lift - Bore
-
5.5 in
-
Cylinder Sizing - Blade Tilt - Bore
-
8.3 in
-
Cylinder Sizing - Ripper Shank Lift - Bore
-
8.3 in
-
Cylinder Sizing - Ripper Shank Angle - Bore
-
7.1 in
-
Cylinder Sizing - Blade Lift - Stroke
-
65.1 in
-
Cylinder Sizing - Blade Tilt - Stroke
-
9.5 in
-
Cylinder Sizing - Ripper Shank Lift - Stroke
-
21.1 in
-
Cylinder Sizing - Ripper Shank Angle - Stroke
-
26 in
-
Note (3)
-
Electro-hydraulic pilot valves assist operations of ripper and dozer controls.
-
Dimensions (Approximate)
Ground Clearance*
-
28.5 in
-
Track Gauge
-
100.4 in
-
Width - Without Trunnions - 610 mm/24 in ES
-
130.4 in
-
Width - Over Trunnions
-
148 in
-
Height - FOPS Cab*
-
162.8 in
-
Height - Top of Stack*
-
171.5 in
-
Height - ROPS/Canopy*
-
173.5 in
-
Note (1)
-
*Includes grouser height for total dimensions on hard surfaces.
