Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module and alternator.
-
-
Note (2)
The following engine configurations are available: – Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. – Noncertified that emits equivalent to U.S. EPA Tier 3.
-
-
Operating Specifications
Operating Weight
105271 lb
-
-
Blade Capacities
7.9 – 22.2 m3 (10.3 – 29.0 yd3)
-
-
Transmission
Transmission Type
Cat planetary power shift
-
-
Forward - 1
4.2 mile/h
-
-
Forward - 2
7.2 mile/h
-
-
Forward - 3
12.6 mile/h
-
-
Forward - 4
22 mile/h
-
-
Reverse - 1
4.2 mile/h
-
-
Reverse - 2
7.6 mile/h
-
-
Reverse - 3
13.3 mile/h
-
-
Direct Drive - Forward 1
Lock-up disabled
-
-
Direct Drive - Forward 2
7.7 mile/h
-
-
Direct Drive - Forward 3
13.7 mile/h
-
-
Direct Drive - Forward 4
23.9 mile/h
-
-
Direct Drive - Reverse 1
4.5 mile/h
-
-
Direct Drive - Reverse 2
8.1 mile/h
-
-
Direct Drive - Reverse 3
14.3 mile/h
-
-
Note
Travel speeds based on 35/65-R33 tire
-
-
1.0 Forward
-
2.2 mile/h
-
2.0 Forward
-
3.9 mile/h
-
3.0 Forward
-
6.8 mile/h
-
1.0 Reverse
-
2.7 mile/h
-
2.0 Reverse
-
4.8 mile/h
-
3.0 Reverse
-
8.4 mile/h
-
Type
-
Planetary powershift
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
Pilot operated LS valve with EH
-
-
Lift/Tilt System
Variable displacement piston
-
-
Maximum Flow at 1,900 rpm
153 gal/min
-
-
Relief Valve Setting - Lift/Tilt
4641 psi
-
-
Cylinders, Double Acting - Lift, Bore and Stroke
139.75 mm × 1021 mm (5.5 in × 40.2 in)
-
-
Cylinders, Double Acting - Left and Right Tilt, Bore and Stroke
140 mm × 230 mm (5.5 in × 9.1 in)
-
-
Pilot System
Variable displacement piston
-
-
Pilot Maximum Flow
13.7 gal/min
-
-
Pilot Relief Valve Setting
580 psi
-
-
Hydraulic System - Steering
Steering System - Circuit
Pilot, load sensing
-
-
Steering System - Pump
Piston, variable displacement
-
-
Maximum Flow
65.8 gal/min
-
-
Relief Valve Setting - Steering
3495 psi
-
-
Total Steering Angle
86 °
-
-
Steering Cycle Times - High Idle
3.1 s
-
-
Steering Cycle Times - Low Idle
5.7 s
-
-
Service Refill Capacities
Fuel Tank
209.5 gal (US)
-
-
Cooling System
31.7 gal (US)
-
-
Crankcase
15.9 gal (US)
-
-
Diesel Exhaust Fluid Tank
8.7 gal (US)
-
-
Transmission
31.7 gal (US)
-
-
Hydraulic System Factory Fill
63.4 gal (US)
-
-
Differential - Final Drives - Front
49.1 gal (US)
-
-
Differential - Final Drives - Rear
49.1 gal (US)
-
-
Hydraulic System - Tank Only
37 gal (US)
-
-
Note (1)
All non-road Tier 4 Final/Stage V diesel engines are required to use: – ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels** up to: • 20% biodiesel FAME (fatty acid methyl este
-
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system co
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430) the system contains 2.1 kg of refrigerant which has a CO2 equivalent of 3.003 metric tonnes.
-
Axles
Front
Fixed
-
-
Rear
Trunnion
-
-
Oscillation Angle
±13°
-
-
Brakes
Brakes
ISO 3450: 2011
-
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
113 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
109 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
113 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
110 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Dimensions
Height - Top of Exhaust Stack
15.9 ft
-
-
Height - Top of Air Cleaner
12.8 ft
-
-
Height - Top of Hood
10.9 ft
-
-
Ground Clearance - Bumper
3.1 ft
-
-
Centerline of Rear Axle to Edge of Bumper
10.5 ft
-
-
Wheel Base
14.9 ft
-
-
Length - Front of Tire
28.4 ft
-
-
Length - Straight Blade on Ground
32.6 ft
-
-
Length - Universal Blade on Ground
34.4 ft
-
-
Centerline of Front Axle to Hitch
7.5 ft
-
-
Ground Clearance
1.7 ft
-
-
Height - Top of Cab
13.7 ft
-
-
Engine - U.S. EPA Tier 2/3 Equivalent
Engine Model
-
Cat® C18
-
Engine Power - Net SAE J1349/ISO 9249
-
452 hp
-
Bore
-
5.7 in³
-
Stroke
-
7.2 in
-
Displacement
-
1106 in³
-
Engine Power - Gross SAE J1995
-
487 hp
-
Engine Power - ISO 14396
-
479 hp
-
Emissions
-
U.S. EPA Tier 2 or Tier 3 equivalent
-
Note (1)
-
All engine ratings apply at 1,750 rpm.
-
Note (2)
-
No derating required up to 4267 m (14,000 ft) altitude.
-
Weights
Operating Weight
-
110225 lb
-
Shipping Weight
-
84373 lb
-
Note (1)
-
D9 Operation Weight includes hydraulic controls, blade tilt cylinder, coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU Blade, Single-Shank Ripper, 610 mm (24 in) ES shoes and operator.
-
Note (2)
-
D9 Operation Weight includes base machine chassis with cab, pivot shaft, roller frames, track and ROPS.
-
Undercarriage
Shoe Type
-
Extreme Service
-
Width - Shoe
-
24 in
-
Shoes/Side
-
43
-
Grouser Height
-
3.3 in
-
Pitch
-
9.4 in
-
Ground Clearance
-
18.1 in
-
Track Gauge
-
88.6 in
-
Length - Track on Ground
-
136.6 in
-
Ground Contact Area
-
45.6 ft²
-
Track Rollers/Side
-
8
-
Number of Carrier Rollers
-
1 per side (optional)
-
Standards
ROPS
-
Rollover Protective Structure (ROPS) meets the following criteria ISO 3471:2008.
-
FOPS
-
Falling Object Protective Structure (FOPS) meets the following criteria ISO 3449:2005 LEVEL II.
-
Sound
-
The average dynamic spectator sound power level when ISO 6395:2008 is used to measure the value for a machine is 116 dB(A). The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling
-
Sound (1)
-
The average dynamic operator sound pressure level when ISO 6396:2008 is used to measure the value for an enclosed cab is 78 dB(A). The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine c
-
Sound (2)
-
Hearing protection may be needed when the machine is operated with an open operator station for extended periods, in a noisy environment, or with a cab that is not properly maintained.
-
Steering and Brakes
Steering Type
-
Differential
-
Brake Type
-
Spring Applied Wet Disc
-
Brake Diameter
-
15.5 in
-
Brake Count
-
8
-
Engine - U.S. EPA Tier 4 Final/EU Stage V
Engine Model
-
Cat® C18
-
Bore
-
5.7 in³
-
Stroke
-
7.2 in³
-
Displacement
-
1106 in³
-
Engine Power - Gross SAE J1995
-
477 hp
-
Engine Power - ISO 14396
-
468 hp
-
Engine Power - Net SAE J1349/ISO 9249
-
440 hp
-
Emissions
-
U.S. EPA Tier 4 / EU Stage V
-
Note (1)
-
All Engine ratings apply at 1,750 rpm.
-
Note (2)
-
No derating required up to 2499 m (8,200 ft).
-
FLUID CAPACITIES
Fuel Tank (Splash Fill)
-
254 gal (US)
-
DEF Tank (Tier 4 only)
-
9.5 gal (US)
-
Fuel Tank (Fast Fill)
-
248 gal (US)
-
Cooling System
-
21 gal (US)
-
Engine Crankcase*
-
10 gal (US)
-
Powertrain
-
40 gal (US)
-
Final Drives (each)
-
4 gal (US)
-
Roller Frames (each)
-
12 gal (US)
-
Pivot Shaft Oil
-
8 gal (US)
-
Hydraulic System Tank
-
24 gal (US)
-
Note
-
*With oil filters.
-
Note 2
-
Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD. B20 should meet ASTM D7467 specification (biodiesel blend stock should meet Cat biodiesel spec, ASTM D6751 or EN 14214). Cat DEO-ULSTM or
-
Note 3
-
All non-road Tier 4 Final diesel engines are required to use only ultra-low sulfur diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less.
-
Note 4
-
Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241.
-
Hydraulic Controls
Pump Type
-
Piston-type geared to flywheel
-
Pump Output - Steering
-
96 gal/min
-
Fan Pump
-
21 gal/min
-
Tilt Cylinder Flow - Rod End Flow
-
53 gal/min
-
Tilt Cylinder Flow - Head End Flow
-
53 gal/min
-
Lift Cylinder Relief Valve Setting
-
3800 lbf/in
-
Tilt Cylinder Relief Valve Setting
-
2799 psi
-
Ripper - Lift - Relief Valve Setting
-
3800 psi
-
Ripper - Pitch - Relief Valve Setting
-
3800 psi
-
Steering System - Pressure
-
5874 psi
-
Tank Capacity
-
24 gal/min
-
Note (1)
-
Steering pump output measured at 1,750 engine rpm and 30 000 kPa (4,350 psi).
-
Note (2)
-
Implement pump output measured at 1,750 engine rpm and 20 000 kPa (2,900 psi).
-
Note (3)
-
Fan pump output measured at 1,750 engine rpm and 17 000 kPa (2,470 psi)
-
Blade - Semi-Universal
Blade Capacity (SAE J1265)
-
17.8 yd³
-
Blade Width (over end bits)
-
171.3 in
-
Blade Height
-
76.1 in
-
Maximum Digging Depth
-
23.9 in
-
Ground Clearance at Full Lift
-
56 in
-
Maximum Tilt
-
37 in
-
Blade Weight
-
10587 lb
-
Total Operating Weight* (with blade and single-shank ripper)
-
110205 lb
-
Note
-
* Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
Blade - Universal
Blade Capacity (SAE J1265)
-
21.7 yd³
-
Blade Width (over end bits)
-
184.3 in
-
Blade Height
-
76.1 in
-
Maximum Digging Depth
-
23.9 in
-
Ground Clearance at Full Lift
-
56 in
-
Maximum Tilt
-
39.9 in
-
Blade Weight
-
12016 lb
-
Total Operating Weight* (with blade and single-shank ripper)
-
111362 lb
-
Note
-
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
Ripper - Single Shank
Maximum penetration force * (shank vertical)
-
35520 lbf
-
Maximum penetration depth (standard tip)
-
48.5 in
-
Pryout Force
-
74637 lbf
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
-
34.7 in
-
Number of Pockets
-
1
-
Weight
-
10701 lb
-
Total Operating Weight* (with SU Blade and noted ripper)
-
110205 lb
-
Note
-
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes
and the noted blade and ripper type.
-
Ripper - Single Shank, Deep Ripping
Maximum penetration force * (shank vertical)
-
38667 lbf
-
Maximum penetration depth (standard tip)
-
68 in
-
Pryout Force
-
74412 lbf
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
-
32.2 in
-
Number of Pockets
-
1
-
Weight
-
10981 lb
-
Total Operating Weight* (with SU Blade and noted ripper)
-
110485 lb
-
Note
-
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
Ripper - Multi-Shank, Adjustable Parallelogram
Maximum Penetration Force - Shank Vertical
-
34621 lbf
-
Maximum Penetration - Standard Tip
-
31.4 in
-
Pry-Out Force - Multi-Shank Ripper with One Tooth
-
81156 lbf
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
-
34.6 in
-
Number of Pockets
-
3
-
Weight
-
12136 lb
-
Total Operating Weight* - With SU-Blade and Ripper
-
111739 lb
-
Note
-
* Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
Dimensions (Approximate)
Ground Clearance*
-
18.1 in
-
Track Gauge
-
88.6 in
-
Width - Without Trunnions - Standard Shoe
-
113 in
-
Width - Over Trunnions
-
130.3 in
-
Height - FOPS Cab*
-
150.4 in
-
Height - Top of Stack*
-
152.6 in
-
Height - ROPS/Canopy*
-
157.5 in
-
Drawbar Height (Center of Clevis)*
-
30 in
-
Length - Track on Ground
-
136.6 in
-
Overall Length - Basic Tractor
-
193.3 in
-
Length - Basic Tractor - With Drawbar
-
206.4 in
-
Length - Basic Tractor - With Winch
-
218.3 in
-
Length - With SU-Blade**
-
259.9 in
-
Length - With U-Blade
-
274.3 in
-
Length - With Single-Shank Ripper
-
257 in
-
Length - With Multi-Shank Ripper
-
257.4 in
-
Overall Length - SU-Blade/SS Ripper
-
323.6 in
-
Note (1)
-
*Includes grouser height for total dimensions on hard surfaces.
-
Winches
Winch Model
-
PA 140VS
-
Weight*
-
3950 lb
-
Oil Capacity
-
4 gal (US)
-
Drum Width
-
12.6 in
-
Wire Cable Diameter - Recommended
-
1.13 in
-
Wire Cable Diameter - Optional
-
1.25 ft
-
Maximum Drum Capacity - Recommended Cable Length
-
257 in
-
Maximum Drum Capacity - Optional Cable Length
-
204 ft
-
Wire Cable Ferrule Size - Outside Diameter
-
2.4 in
-
Wire Cable Ferrule Size - Length
-
2.8 in
-
Note
-
*Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope. With counterweight: 3700 kg (8,150 lb).
