Net power is tested per ISO 9249:2007 and SAE J1349:2011 and as advertised is the power available at the flywheel when the engine is equipped with fan, air intake system, exhaust system and alternator.
Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module and alternator.
-
Note (2)
All non-road U.S. EPA Tier 4 Final, EU Stage V, Japan 2014 (Tier 4 Final) and Korea Tier 4 Final diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm EPA/10 ppm EU (mg/kg) sulfur or less.
The following engine configurations are available: – Meets U.S. EPA Tier 4 Final and EU Stage V emission standards. – Noncertified that emits equivalent to U.S. EPA Tier 3.
-
Net Power - SAE J1349:2011
-
496 hp
-
Rated Speed
-
1900 r/min
-
Peak Power Speed
-
1500 r/min
-
Gross Power - SAE J1995:2014
-
562 hp
-
Bore
-
5.7 in
-
Stroke
-
7.2 in
-
Peak Torque - 1,300 rpm
-
2092 lb/ft
-
Torque Rise
-
52 %
-
Weights
Operating Weight
20640 lb
-
-
Operating Weight - LGP
21369 lb
-
-
Operating Weight - LGP, 762 mm/30 in
21810 lb
-
-
Note (2)
For machine with ripper, add 554 kg (1,222 lb).
-
-
Note (1)
Specifications shown are for machine equipped with dozer blade, EROPS cab, back-up alarm, operator, coolant, lubricants and full fuel tank.
-
-
Transmission
Drive Pumps
1
-
-
Maximum Travel Speed - Forward
5.6 mile/h
-
-
Maximum Travel Speed - Reverse
6.2 mile/h
-
-
Track Motors
2
-
-
Relief Valve Settings
7033 psi
-
-
Transmission Type
-
Cat planetary power shift
-
Forward - 1
-
4.2 mile/h
-
Forward - 2
-
7.2 mile/h
-
Forward - 3
-
12.6 mile/h
-
Forward - 4
-
22 mile/h
-
Reverse - 1
-
4.2 mile/h
-
Reverse - 2
-
7.6 mile/h
-
Reverse - 3
-
13.3 mile/h
-
Direct Drive - Forward 1
-
Lock-up disabled
-
Direct Drive - Forward 2
-
7.7 mile/h
-
Direct Drive - Forward 3
-
13.7 mile/h
-
Direct Drive - Forward 4
-
23.9 mile/h
-
Direct Drive - Reverse 1
-
4.5 mile/h
-
Direct Drive - Reverse 2
-
8.1 mile/h
-
Direct Drive - Reverse 3
-
14.3 mile/h
-
Note
-
Travel speeds based on 35/65-R33 tire
-
Hydraulic Controls
Pump Output
17.2 gal/min
-
-
Relief Valve Settings
2988 psi
-
-
Ripper
Type
Parallelogram
-
-
Number of Shanks
3
-
-
Height
6.5 in
-
-
Weight
1222 lb
-
-
Maximum Digging Depth
13.3 in
-
-
Maximum Reach - Ground Line
30.2 in
-
-
Overall Width
67.3 in
-
-
Maximum Ground Clearance Under Tip
17.6 in
-
-
Undercarriage
Ground Pressure - LGP
4.5 psi
-
-
Track Gauge - LGP
69 in
-
-
Length - Track on Ground - LGP
91 in
-
-
Number of Shoes - Each Side - Sealed and Lubricated Track (SALT) Undercarriage
40
-
-
Ground Pressure - LGP, 762 mm (30 in)
3.9 psi
-
-
Length - Track on Ground - LGP, 762 mm (30 in)
91 in
-
-
Shoe Width - LGP
26 in
-
-
Shoe Width - LGP, 762 mm (30 in)
30 in
-
-
Track Gauge
63 in
-
-
Number of Rollers - Each Side
7
-
-
Track Gauge - LGP, 762 mm (30 in)
73 in
-
-
Shoe Width - Standard
20 in
-
-
Undercarriage
Ground Pressure
5.7 psi
-
-
Length of Track on Ground
91 in
-
-
Number of Shoes - Each Side - Abrasion Undercarriage
36
-
-
Service Refill Capacities
Cooling System
5 gal (US)
31.7 gal (US)
-
Final Drive - Each - LGP
2.6 gal (US)
-
-
Crankcase - With Filter
2.8 gal (US)
-
-
Transmission - Hydraulic Tank
23.8 gal (US)
-
-
Fuel Tank
51.5 gal (US)
209.5 gal (US)
-
Diesel Exhaust Fluid (DEF) Tank
4.9 gal (US)
-
-
Crankcase
-
15.9 gal (US)
-
Diesel Exhaust Fluid Tank
-
8.7 gal (US)
-
Transmission
-
31.7 gal (US)
-
Hydraulic System Factory Fill
-
63.4 gal (US)
-
Differential - Final Drives - Front
-
49.1 gal (US)
-
Differential - Final Drives - Rear
-
49.1 gal (US)
-
Hydraulic System - Tank Only
-
37 gal (US)
-
Note (1)
-
All non-road Tier 4 Final/Stage V diesel engines are required to use: – ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels** up to: • 20% biodiesel FAME (fatty acid methyl este
-
Service Refill Capacities
Final Drives - Each Side
2.6 gal (US)
-
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system co
-
Dimensions
BLADE: Blade Width - LGP
126.7 in
-
-
Track Gauge - LGP, 762 mm (30 in)
73 in
-
-
BLADE: Digging Depth - LGP
23.2 in
-
-
Track Gauge - LGP
67.9 in
-
-
BLADE: Blade Capacity (SAE) - LGP
3.06 yd³
-
-
BLADE: Blade Width at Maximum Angle - LGP
115.8 in
-
-
BLADE: Blade Cutting Edge Angle, Adjustable - LGP
52° to 58°
-
-
Ground Clearance - LGP, 762 mm (30 in)
13 in
-
-
BLADE: Blade Height - LGP
39.8 in
-
-
BLADE: Blade Lift Height - LGP
30.2 in
-
-
Ground Clearance - LGP
13 in
-
-
Overall Length - With Blade - LGP, 762 mm (30 in)
169.6 in
-
-
Overall Length - With Blade - LGP
169.6 in
-
-
Note
With Ripper Attachment (add to Length of Basic Dozer) - 1177 mm (46.3 in)
-
-
BLADE: Maximum Tilt - LGP
17.7 in
-
-
BLADE: Maximum Angle (either side) - LGP
25°
-
-
Length of Basic Dozer (without blade) - Standard
128.7 in
-
-
Dozer Height - Standard
109 in
-
-
Width of Dozer (standard shoes, no blade) - LGP
94.9 in
-
-
Width of Dozer (standard shoes, no blade) - LGP, 762 mm (30 in)
103.5 in
-
-
Length of Basic Dozer (without blade) - LGP
128.7 in
-
-
Dozer Height - LGP, 762 mm (30 in)
109 in
-
-
Width of Dozer (standard shoes, no blade) - Standard
83 in
-
-
Length of Basic Dozer (without blade) - LGP, 762 mm (30 in)
128.7 in
-
-
Dozer Height - LGP
109 in
-
-
Height - Top of Exhaust Stack
-
15.9 ft
-
Height - Top of Air Cleaner
-
12.8 ft
-
Height - Top of Hood
-
10.9 ft
-
Ground Clearance - Bumper
-
3.1 ft
-
Centerline of Rear Axle to Edge of Bumper
-
10.5 ft
-
Wheel Base
-
14.9 ft
-
Length - Front of Tire
-
28.4 ft
-
Length - Straight Blade on Ground
-
32.6 ft
-
Length - Universal Blade on Ground
-
34.4 ft
-
Centerline of Front Axle to Hitch
-
7.5 ft
-
Ground Clearance
-
1.7 ft
-
Height - Top of Cab
-
13.7 ft
-
Dimensions
BLADE: Blade Capacity (SAE) - Standard
2.86 yd³
-
-
Track Gauge - Standard
63 in
-
-
BLADE: Digging Depth - Standard
23.8 in
-
-
BLADE: Blade Lift Height - Standard
30.2 in
-
-
Ground Clearance - Standard
13 in
-
-
Overall Length - With Blade - Standard
170.7 in
-
-
BLADE: Blade Cutting Edge Angle, Adjustable - Standard
52° to 58°
-
-
BLADE: Blade Height - Standard
42.2 in
-
-
BLADE: Maximum Tilt - Standard
15.8 in
-
-
Note
Abrasion Undercarriage
-
-
BLADE: Blade Width - Standard
109.5 in
-
-
BLADE: Blade Width at Maximum Angle - Standard
103.8 in
-
-
BLADE: Maximum Angle (either side) - Standard
25°
-
-
Engine
Power Train
Hydrostatic
-
-
Cab
ROPS
ISO 3471:2008
-
-
FOPS
ISO 3449:2005 Level II
-
-
Retrieval Winch
Maximum Line Pull - Bare Drum
32150 lb
-
-
Control
Hydraulic
-
-
Rope Diameter - Optional
0.75 in
-
-
Drum Capacity - Optional Cable
195 ft
-
-
Maximum Line Speed - Full Drum
79 ft/min
-
-
Drum Capacity - Recommended Cable
277 ft
-
-
Winch Drive
Hydraulic
-
-
Weight
1747 lb
-
-
Maximum Line Pull - Full Drum
20350 lb
-
-
Rope Diameter - Recommended
0.63 in
-
-
Maximum Line Speed - Bare Drum
50 ft/min
-
-
Speed
Variable
-
-
Winch Length
35.63 in
-
-
Drum Diameter
8 in
-
-
Overall width
27.91 in
-
-
Drum Width
9.65 in
-
-
Throat Clearance
5.6 in
-
-
High Performance Winch
Winch length
27.76 in
-
-
Rope diameter – optional
0.75 in
-
-
Maximum line speed – bare drum
131 ft/min
-
-
Maximum line pull – bare drum
40000 lb
-
-
Weight
1345 lb
-
-
Drum capacity – optional
256 ft
-
-
Maximum line speed – full drum
207 ft/min
-
-
Rope diameter – recommended
0.63 in
-
-
Winch drive
Hydrostatic
-
-
Throat clearance
6.75 in
-
-
Drum diameter
10 in
-
-
Overall width
29.2 in
-
-
Drum width
10.8 in
-
-
Maximum line pull – full drum
25000 lb
-
-
Speed
Variable
-
-
Drum capacity – recommended cable
371 ft
-
-
Control
Hydraulic
-
-
Operating Specifications
Operating Weight
-
105271 lb
-
Blade Capacities
-
7.9 – 22.2 m3 (10.3 – 29.0 yd3)
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
-
Pilot operated LS valve with EH
-
Lift/Tilt System
-
Variable displacement piston
-
Maximum Flow at 1,900 rpm
-
153 gal/min
-
Relief Valve Setting - Lift/Tilt
-
4641 psi
-
Cylinders, Double Acting - Lift, Bore and Stroke
-
139.75 mm × 1021 mm (5.5 in × 40.2 in)
-
Cylinders, Double Acting - Left and Right Tilt, Bore and Stroke
-
140 mm × 230 mm (5.5 in × 9.1 in)
-
Pilot System
-
Variable displacement piston
-
Pilot Maximum Flow
-
13.7 gal/min
-
Pilot Relief Valve Setting
-
580 psi
-
Hydraulic System - Steering
Steering System - Circuit
-
Pilot, load sensing
-
Steering System - Pump
-
Piston, variable displacement
-
Maximum Flow
-
65.8 gal/min
-
Relief Valve Setting - Steering
-
3495 psi
-
Total Steering Angle
-
86 °
-
Steering Cycle Times - High Idle
-
3.1 s
-
Steering Cycle Times - Low Idle
-
5.7 s
-
Axles
Front
-
Fixed
-
Rear
-
Trunnion
-
Oscillation Angle
-
±13°
-
Brakes
Brakes
-
ISO 3450: 2011
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
-
72 dB(A)
-
Machine Sound Power Level (ISO 6395:2008)
-
113 dB(A)
-
Operator Sound Pressure Level (ISO 6396:2008)*
-
72 dB(A)
-
Machine Sound Power Level (ISO 6395:2008)**
-
109 dB(A)
-
Note (1)
-
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
Note (2)
-
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
Note (3)
-
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
Note (4)
-
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
Note (5)
-
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
-
72 dB(A)
-
Machine Sound Power Level (ISO 6395:2008)
-
113 dB(A)
-
Operator Sound Pressure Level (ISO 6396:2008)*
-
72 dB(A)
-
Machine Sound Power Level (ISO 6395:2008)**
-
110 dB(A)
-
Note (1)
-
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
Note (2)
-
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
Note (3)
-
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
Note (4)
-
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed.
-
Note (5)
-
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
