Engine meets Tier 4 Final/Stage V emission standards.
-
-
Note
Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
-
-
Maximum Gross Power - ISO 14396
121 HP
-
-
Net Power @ 1,700 rpm – ISO 9249:2007, SAE J1349:2011
-
404 HP
-
Note (1)
-
Cat engine meets U.S. EPA Tier 4 Final, EU Stage V, Korea Stage V, and Japan 2014 emission standards.
-
Note (2)
-
The net power advertised is the power available at the flywheel when the engine is equipped with fan, alternator, air cleaner, and aftertreatment.
-
Note (3)
-
Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: • 20% biodiesel FAME (fatty acid methyl ester)* • 100% renewable diesel, HVO (h
-
Engine Power @ 1,700 rpm – ISO 14396:2002
-
432 HP
-
Gross Torque @ 1,200 rpm – SAE J1995:2014
-
1636 lb/ft
-
Gross Power @ 1,700 rpm – SAE J1995:2014
-
436 HP
-
Net Torque @ 1,100 rpm – ISO 9249:2007, SAE J1349:2011
-
1515 lb/ft
-
Engine Torque @ 1,200 rpm – ISO 14396:2002
-
1620 lb/ft
-
Weights
Operating Weight
21742 lb
78264 lb
-
Note
-
Weight based on a machine configuration with Bridgestone 875/65R29 VLTS L4 radial tires, full fluids, operator, standard counterweight, ride control, cold start, roading fenders, Product Link, open differential axles (front/rear), secondary steering, soun
-
Buckets
Bucket Capacities
1.3-3.5 m3 (1.7-4.6 yd3)
-
-
Bucket Capacities - General Purpose
1.3-1.9 m³ (1.7-2.5 yd³)
-
-
Bucket Capacities - Light Material
2.5-3.5 m³ (3.3-4.6 yd³)
-
-
Sustainability
Recyclability
95%
-
-
Service Refill Capacities
Transmission
0.8 gal (US)
20.3 gal (US)
-
Engine Crankcase
2.6 gal (US)
-
-
Axles - Rear
4.5 gal (US)
-
-
Hydraulic System - Including Tank
25.9 gal (US)
-
-
Cooling System
5.7 gal (US)
13.7 gal (US)
-
Fuel Tank
43.6 gal (US)
112.5 gal (US)
-
Hydraulic Tank
14.5 gal (US)
40.4 gal (US)
-
Note
DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
-
-
Diesel Exhaust Fluid (DEF) Tank
4.8 gal (US)
-
-
Axles - Front
4.5 gal (US)
-
-
Crankcase
-
9.8 gal (US)
-
DEF Tank
-
5.5 gal (US)
-
Differential - Final Drives - Front
-
24.3 gal (US)
-
Differential - Final Drives - Rear
-
24.3 gal (US)
-
Cab
ROPS
ISO 3471:2008
-
-
FOPS
ISO 3449:2005
-
-
Note (3)
The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A).
-
-
Note (2)
The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A).
-
-
Note (1)
Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
-
-
Note (4)
*The measurements were conducted with the cab doors and windows closed.
-
-
Loader Hydraulic System
Maximum Flow - Implement Pump
43.6 gal/min
-
-
Relief Pressure - Tilt Cylinder
4641 psi
-
-
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard
25 gal/min
-
-
Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure
4641 psi
-
-
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level
2.7 s
-
-
Note
All cycle times listed are with cylinder snubbing turned off.
-
-
Maximum Working Pressure - Implement Pump
4061 psi
-
-
Hydraulic Cycle Time - Total Cycle Time
11.5 s
-
-
Hydraulic Cycle Time - Rackback
2.2 s
-
-
Hydraulic Cycle Time - Dump, at Maximum Reach
1.8 s
-
-
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift
4.8 s
-
-
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High
40 gal/min
-
-
Maximum Flow - Implement Pump - 4rd Function, Maximum Flow
25 gal/min
-
-
Steering
Maximum Working Pressure - Steering Pump
3190 psi
-
-
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed
2.3 s
-
-
Steering Articulation Angle - Each Direction
40 °
-
-
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
3.4 turns
-
-
Maximum Flow - Steering Pump
21.7 gal/min
-
-
Transmission
Note
*Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
Maximum travel speed in standard vehicle with empty bucket and standard L4 tires with 914 mm (36 in) roll radius.
Other tire choices are available. Contact your Cat dealer for details.
-
-
Note (3)
Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
-
-
Note (2)
In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
-
-
Bucket Capacities
Bucket Range
-
4.8-17.2 m³ 6.25-22.5 yd³
-
Sound
Note (1)
-
* For machines in European Union countries and in countries that adopt the “EU Directives.”
-
Note (2)
-
European Union Directive “2000/14/EC” as amended by “2005/88/EC.”
-
With Cooling Fan Speed at 70% of Maximum Value - Exterior Sound Power Level*
-
107
-
With Cooling Fan Speed at 70% of Maximum Value - Operator Sound Pressure Level (ISO 6396:2008)
-
70 dB(A)
-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Power Level (ISO 6395:2008)
-
110 dB(A)
-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Pressure Level (SAE J88:2013)
-
75
-
With Cooling Fan Speed at Maximum Speed - Operator Sound Pressure Level (ISO 6396:2008)
-
70 dB(A)
-
Air Conditioning System
Air Conditioning
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.9 kg (4.2 lb) of refrigerant which has a CO2 equivalent 2.717 metric tonnes (2.995 tons).
-
Operating Specifications
Breakout Force
-
59060 lbf
-
Note (1)
-
For a machine configuration as defined under Weight.
-
Note (2)
-
Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing.
-
Static Tipping Load - Full 40° Turn - No Tire Deflection
-
22418 kg
-
Static Tipping Load - Full 40° Turn - With Tire Deflection
-
46526 lb
-
Hydraulic System
Implement System - Maximum Operating Pressure
-
4975 psi
-
Implement System - Maximum Pump Output at 2,250 rpm
-
119 gal/min
-
Hydraulic Cycle Time - Total
-
10.1 seconds
-
Dimensions
Note
-
All dimensions are approximate and based on machine equipped with 6.1 m3 (8.0 yd3) general purpose bucket with BOCE and Bridgestone 875/65R29 VLTS L4 radial tires.
