Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 standards in effect at the time of manufacture. Net power advertised is the power available at rated speed of 2,000 rpm, measured at the flywheel when engine is equipped with fan, air cleaner,
Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture.
-
Emissions
Meets U.S. EPA Tier 4 Final, EU Stage V and Korea Tier 5 emission standards
Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent
-
Base Power (1st Gear) - Net
-
238 HP
-
Speed at Rated Power
-
1,850 rpm
-
Note (3)
-
Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator.
-
Standard Capability
-
122 °F
-
Note (2)
-
Optimized VHP Plus is standard for the 14M3.
-
Torque Rise
-
41%
-
Maximum Altitude - Full Power
-
13900 ft
-
Maximum Torque - VHP Plus
-
1137 lb/ft
-
Maximum Altitude - Full Power (Tier 3)
-
14349 ft
-
Maximum Altitude - Full Power (Tier 2)
-
12049 ft
-
Standard - Fan Speed - Minimum
-
550 rpm
-
Note (4)
-
Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp)
-
Note (5)
-
Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
-
Standard - Fan Speed - Maximum
-
1,600 rpm
-
Number of Cylinders
-
6
-
Weights
Operating Weight - Typically Equipped
14496 lb
57250 lb
-
Gross Vehicle Weight - Base* - Total
-
50980 lb
-
Gross Vehicle Weight - Base* - Front Axle
-
13994 lb
-
Gross Vehicle Weight - Typically Equipped - Total
-
57250 lb
-
Gross Vehicle Weight - Typically Equipped - Rear Axle
-
42005 lb
-
Gross Vehicle Weight - Typically Equipped - Front Axle
-
15245 lb
-
Gross Vehicle Weight - Base* - Rear Axle
-
36994 lb
-
Note
-
*Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab.
-
Moldboard
Blade Width
12 ft
14 ft
-
Cutting Edge Width
6 in
-
-
Throat Clearance
4.7 in
4.6 in
-
Arc Radius
16.3 in
16.3 in
-
End Bit - Width
152 in
-
-
Blade Height
20 in
-
-
Blade Width - With End Bits
-
169 in
-
Blade Height - With Cutting Edge
-
24.9 in
-
Blade Width - Without End Bits
-
164 in
-
Blade Height - Without Cutting Edge
-
23 in
-
Machine Weight
All-Wheel Drive (AWD) Weight
36376 lb
-
-
Dimensions
Length of Machine*
391.4 in
-
-
Maximum Height
149.1 in
-
-
Width
94.6 in
-
-
Note
*Typically equipped with push block and ripper.
-
-
Blade Range
Blade Tip Range - Backward
5°
5°
-
Moldboard Sideshift - Right
26.1 in
31.1 in
-
Moldboard Sideshift - Left
20.2 in
29.1 in
-
Maximum Lift Above Ground
16.1 in
16.5 in
-
Circle Centershift - Left
25.8 in
25.6 in
-
Blade Tip Range - Forward
40°
40°
-
Circle Centershift - Right
25.8 in
20.5 in
-
Maximum Depth of Cut
30.5 in
23.3 in
-
Maximum Shoulder Reach Outside of Tires - Right
-
78.9 in
-
Maximum Shoulder Reach Outside of Tires - Left
-
73.6 in
-
Service Refill Capacities
Cooling System
10.3 gal (US)
15.9 gal (US)
-
Circle Drive without Slip Clutch
0.4 gal (US)
-
-
Hydraulic System
14.5 gal (US)
33 gal (US)
-
Circle Drive with Slip Clutch
1.8 gal (US)
-
-
Transmission
4.5 gal (US)
-
-
Diesel Exhaust Fluid Tank (Tier 4 Only)
3.2 gal (US)
5.8 gal (US)
-
Fuel Tank
71 gal (US)
109.9 gal (US)
-
Engine Crankcase
2 gal (US)
-
-
Transmission and Differential
-
23.5 gal (US)
-
Circle Drive
-
1.8 gal (US)
-
Sustainability
Recyclability
92%
-
-
Frame
Circle - Outer Diameter
-
71.7 in
-
Front Axle - Wheel Lean - Left/Right
-
17.1°
-
Front Axle - Total Oscillation per Side
-
32°
-
Air Conditioning System
Air Conditioning
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton).
