Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 standards in effect at the time of manufacture.
-
Note (2)
-
Net power advertised is the power available at rated speed of 2,200 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator.
-
Note (3)
-
Power as declared per ISO 14396
-
Engine Power AWD (ISO 14396)
-
196 HP
-
Weights
Operating Weight - Typically Equipped
43950 lb
38912 lb
-
Gross Vehicle Weight - Maximum - Front Axle
17075 lb
-
-
Gross Vehicle Weight - Maximum - Rear Axle
38069 lb
-
-
Operating Weight - Typically Equipped - Front Axle
12549 lb
-
-
Operating Weight - Typically Equipped - Rear Axle
31401 lb
-
-
Gross Vehicle Weight - Base - Front Axle
9601 lb
-
-
Gross Vehicle Weight - Base - Rear Axle
28590 lb
-
-
Gross Vehicle Weight - Maximum - Total
55144 lb
-
-
Operating Weight - Typically Equipped - Total
43950 lb
-
-
Gross Vehicle Weight - Base - Total
38191 lb
-
-
Note
-
* Typically equipped operating weight is calculated with full fuel tank, coolant, lubricants, operator, push block, rear ripper, tires on multi-piece rims (*17.5-25 Bias/**17.5R-25), and other equipment.
-
Moldboard
Blade Width
12 ft
12 ft
-
Moldboard - Height
24 in
-
-
Moldboard - Thickness
0.87 in
-
-
Arc Radius
16.3 in
16.3 in
-
Throat Clearance
6.5 in
4.4 in
-
Cutting Edge Width
6 in
6 in
-
Cutting Edge Thickness
0.6 in
-
-
End Bit - Width
6 in
-
-
End Bit - Thickness
0.6 in
-
-
Blade Pull - Base GVW
25732 lb
-
-
Blade Pull - Maximum GVW
34262 lb
-
-
Blade Down Pressure - Base GVW
16480 lb
-
-
Blade Down Pressure - Maximum GVW
29308 lb
-
-
Moldboard - Blade Width
12 ft
-
-
Blade Height
-
24 in
-
End Bit
-
6 in
-
Operating Specifications
Top Speed - Forward
29 mile/h
-
-
Top Speed - Reverse
23 mile/h
-
-
Turning Radius - Outside Front Tires
25.59 ft
-
-
Steering Range - Left/Right
50°
-
-
Articulation Angle - Left/Right
20°
-
-
Forward - 1st
2.5 mile/h
-
-
Forward - 2nd
3.4 mile/h
-
-
Forward - 3rd
5 mile/h
-
-
Forward - 4th
6.9 mile/h
-
-
Forward - 5th
10.6 mile/h
-
-
Forward - 6th
14.5 mile/h
-
-
Forward - 7th
19.9 mile/h
-
-
Forward - 8th
29 mile/h
-
-
Reverse - 1st
2 mile/h
-
-
Reverse - 2nd
3.7 mile/h
-
-
Reverse - 3rd
5.4 mile/h
-
-
Reverse - 4th
8.4 mile/h
-
-
Reverse - 5th
15.7 mile/h
-
-
Reverse - 6th
23 mile/h
-
-
Service Refill
Fuel Capacity
104 gal (US)
-
-
Cooling System
15 gal (US)
-
-
Hydraulic System - Total
26.4 gal (US)
-
-
Hydraulic System - Tank
16.9 gal (US)
-
-
Transmission - Differential - Final Drives
18.5 gal (US)
-
-
Diesel Exhaust Fluid
5.8 gal (US)
-
-
Engine Oil
7.9 gal (US)
-
-
Tandem Housing - Each
20 gal (US)
-
-
Front Wheel Spindle Bearing Housing
0.13 gal (US)
-
-
Circle Drive Housing
1.8 gal (US)
-
-
Power Train
Forward/Reverse Gears
8 Forward/6 Reverse
-
-
Transmission
APECS, Direct Drive, Powershift
-
-
Brakes - Service
Multiple Oil Disc
-
-
Brakes - Service - Surface Area
3565 in²
-
-
Brakes - Parking
Multiple Oil Disc
-
-
Brakes - Secondary
Dual Circuit
-
-
Hydraulic System
Circuit Type
Parallel
-
-
Pump Type
Variable Piston
-
-
Pump Output
55.7 gal/min
-
-
Maximum System Pressure
3500 psi
-
-
Reservoir Tank Capacity
16.9 gal (US)
-
-
Standby Pressure
885 psi
-
-
Frame
Drawbar - Width
3 in
-
-
Circle - Diameter
60.2 in
-
-
Circle - Blade Beam Thickness
1.6 in
-
-
Drawbar - Height
6 in
-
-
Front Frame Structure - Width
12 in
-
-
Front Frame Structure - Height
12.6 in
-
-
Circle - Height
5.4 in
-
-
Drawbar - Thickness
0.5 in
-
-
Front-Top/Bottom Plate - Width
12 in
-
-
Front-Top/Bottom Plate - Thickness
0.87 in
-
-
Front Axle - Height to Center
23.5 in
-
-
Front Axle - Wheel Lean - Left/Right
18°
-
-
Front Axle - Total Oscillation per Side
32°
-
-
Blade Range
Circle Centershift - Right
28.7 in
-
-
Circle Centershift - Left
27.4 in
-
-
Moldboard Sideshift - Right
26 in
-
-
Moldboard Sideshift - Left
20.1 in
-
-
Maximum Blade Position Angle
90°
-
-
Blade Tip Range - Forward
40°
-
-
Blade Tip Range - Backward
5°
-
-
Maximum Shoulder Reach Outside of Tires - Right
77.9 in
-
-
Maximum Shoulder Reach Outside of Tires - Left
70.5 in
-
-
Maximum Lift Above Ground
18.9 in
18.7 in
-
Maximum Depth of Cut
28.1 in
28.1 in
-
Circle Center Shift Left
-
29.6 in
-
Circle Center Shift Right
-
28.7 in
-
Maximum Shoulder Reach Left
-
74.3 in
-
Maximum Shoulder Reach Right
-
71.3 in
-
Moldboard Side Shift Left
-
25.6 in
-
Moldboard Side Shift Right
-
20.7 in
-
Blade Tip Range Backward
-
5
-
Blade Tip Range Forward
-
40
-
Ripper
Ripper Shank Holder Spacing
21 in
-
-
Ripping Depth - Maximum
16.8 in
-
-
Ripper Shank Holders
5
-
-
Penetration Force
20812 lb
-
-
Pry-Out Force
27794 lb
-
-
Machine Length Increase, Beam Raised
40.6 in
-
-
Scarifier
Front, V-Type, 5 or 11 Tooth - Scarifier Shank Holders
11-May
-
-
Front, V-Type, 5 or 11 Tooth - Scarifying Depth, Maximum
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
-
-
Note
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430).The system contains 2.0 kg of refrigerant which has a CO2 equivalent of 2.86 metric tonnes.