CALL US: 800-937-2326   |   PARTS: 800-937-2311   |   LOCATIONS
  • Home
  • Compare

    • Compare Equipment Go Back

    140 Motor Grader LVR
    View Product
    24 Motor Grader
    View Product Remove
    14 Motor Grader
    View Product Remove

    Engine
    Net Power - EEC 80/1269 250 HP 535 HP -
    Net Power - ISO 9249/SAE J1349 250 HP - -
    Standard Capability 109 °F 122 °F 122 °F
    Engine RPM 2,000 - -
    Engine Model Cat C9.3 Cat C27 Cat C13
    Bore 4.5 in 5.4 in 5.1 in
    Emissions U.S. EPA Tier 4 Final/EU Stage V Tier 4 Final/Stage IV or Equivalent to Tier 2/Stage II Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent
    Displacement 567.5 in³ 1648 in³ 763 in³
    Stroke 5.9 in 6 in 6.2 in
    Number of Cylinders 6 12 6
    Torque Rise - ISO 9294 44% - -
    Note (1) - Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture.
    Note (3) - Net power advertised is the power available at rated speed of 1,800 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator.
    Note (2) - Optimized VHP Plus is standard for the 24. Optimized VHP Plus is standard for the 14M3.
    Note (4) - Power as declared per ISO 14396. Rated rpm 1,800 (561 hp) Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp)
    Base Power (1st Gear) - Net - - 238 HP
    Speed at Rated Power - - 1,850 rpm
    Torque Rise - - 41%
    Maximum Altitude - Full Power - - 13900 ft
    Maximum Torque - VHP Plus - - 1137 lb/ft
    Maximum Altitude - Full Power (Tier 3) - - 14349 ft
    Maximum Altitude - Full Power (Tier 2) - - 12049 ft
    Standard - Fan Speed - Minimum - - 550 rpm
    Note (5) - - Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
    Standard - Fan Speed - Maximum - - 1,600 rpm

    Weights
    Operating Weight - Typically Equipped 20236 lb 165314 lb 57250 lb
    Gross Vehicle Weight - Base* - Total - - 50980 lb
    Gross Vehicle Weight - Base* - Front Axle - - 13994 lb
    Gross Vehicle Weight - Typically Equipped - Total - - 57250 lb
    Gross Vehicle Weight - Typically Equipped - Rear Axle - - 42005 lb
    Gross Vehicle Weight - Typically Equipped - Front Axle - - 15245 lb
    Gross Vehicle Weight - Base* - Rear Axle - - 36994 lb
    Note - - *Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab.

    Moldboard
    Blade Width 12 ft 24 ft 14 ft
    Cutting Edge 6 in - -
    Arc Radius 16.3 in - 16.3 in
    Throat Clearance 6.5 in - 4.6 in
    End Bit 6 in - -
    Blade Height - 40 in -
    Blade Width - With End Bits - - 169 in
    Blade Height - With Cutting Edge - - 24.9 in
    Blade Width - Without End Bits - - 164 in
    Blade Height - Without Cutting Edge - - 23 in

    Dimensions
    Basic Blade Width 140 in - -
    Length of Machine* 397.6 in - -
    Width 97.6 in - -
    Note *Typically equipped with push block and ripper. - -
    Maximum Height 132 in - -

    Service Refill
    Hydraulic System 14.5 gal (US) - -
    Engine Crankcase 7.9 gal (US) - -
    Circle Drive 1.8 gal (US) - -
    Fuel Tank 100 gal (US) - -
    Front Wheel Spindle Bearing - Each 0.13 gal (US) - -

    Machine Weight
    Note *Typically equipped with push block and ripper. - -
    All-Wheel Drive (AWD) Weight 44613 lb - -
    Weight* 42325 lb 161695 lb -

    Blade Range
    Maximum Lift Above Ground 18.9 in 16.1 in 16.5 in
    Maximum Depth of Cut 28.9 in 21.7 in 23.3 in
    Circle Centershift - Left - - 25.6 in
    Circle Centershift - Right - - 20.5 in
    Blade Tip Range - Backward - - 5°
    Maximum Shoulder Reach Outside of Tires - Right - - 78.9 in
    Moldboard Sideshift - Right - - 31.1 in
    Moldboard Sideshift - Left - - 29.1 in
    Maximum Shoulder Reach Outside of Tires - Left - - 73.6 in
    Blade Tip Range - Forward - - 40°

    Frame
    Circle - Outer Diameter - - 71.7 in
    Front Axle - Wheel Lean - Left/Right - - 17.1°
    Front Axle - Total Oscillation per Side - - 32°

    Service Refill Capacities
    Transmission and Differential - - 23.5 gal (US)
    Diesel Exhaust Fluid Tank (Tier 4 Only) - - 5.8 gal (US)
    Hydraulic System - - 33 gal (US)
    Circle Drive - - 1.8 gal (US)
    Cooling System - - 15.9 gal (US)
    Fuel Tank - - 109.9 gal (US)

    Air Conditioning System
    Air Conditioning - - The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton).
    Add a Similar Product: