Compare Equipment Go Back

14 Motor Grader

Engine

Net Power - ISO 9249/SAE J1349 130 hp - -
Note (2) Net power advertised is the power available at rated speed of 2,000 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. Optimized VHP Plus is standard for the 14M3. -
Displacement 427.8 in³ 763 in³ -
Derating Altitude 9842.5 ft - -
Maximum Torque - ISO 9249 606 lb/ft - -
Net Power Range (Tier 3) 130 hp - -
Note (3) Power as declared per ISO 14396 Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. -
Bore 4.1 in 5.1 in -
Engine RPM 2,000 - -
Maximum Torque - AWD On 611 lb/ft - -
Note (1) Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture." Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. -
Engine Model Cat 7.1 Cat C13 -
Stroke 5.3 in 6.2 in -
Emissions U.S. EPA Tier 4 Final/EU Stage V - U.S. EPA Tier 3/EU Stage IIIA Tier 4 Final/Stage V, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent -
Standard Capability 122 °F 122 °F -
Number of Cylinders 6 6 -
Derating Altitude (AWD) 5499 ft - -
Torque Rise - ISO 9294 42% - -
All-Wheel Drive Net Power Range (Tier 4) 174 kW - -
Base Power (1st Gear) - Net - 238 hp -
Speed at Rated Power - 1,850 rpm -
Torque Rise - 41% -
Maximum Altitude - Full Power - 13900 ft -
Maximum Torque - VHP Plus - 1137 lb/ft -
Maximum Altitude - Full Power (Tier 3) - 14349 ft -
Maximum Altitude - Full Power (Tier 2) - 12049 ft -
Standard - Fan Speed - Minimum - 550 rpm -
Note (4) - Power as declared per ISO 14396. Rated rpm 1,850. VHP+ = 228 kW (306 hp) -
Note (5) - Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. -
Standard - Fan Speed - Maximum - 1,600 rpm -

Weights

Operating Weight - Typically Equipped 35067 lb 57250 lb -
Gross Vehicle Weight - Base* - Total - 50980 lb -
Gross Vehicle Weight - Base* - Front Axle - 13994 lb -
Gross Vehicle Weight - Typically Equipped - Total - 57250 lb -
Gross Vehicle Weight - Typically Equipped - Rear Axle - 42005 lb -
Gross Vehicle Weight - Typically Equipped - Front Axle - 15245 lb -
Gross Vehicle Weight - Base* - Rear Axle - 36994 lb -
Note - *Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab. -

Moldboard

Blade Width 12 ft 14 ft -
Blade Height 24 in - -
Throat Clearance 4.1 in 4.6 in -
End Bit 6 in - -
Cutting Edge 6 in - -
Arc Radius 16.3 in 16.3 in -
Blade Width - With End Bits - 169 in -
Blade Height - With Cutting Edge - 24.9 in -
Blade Width - Without End Bits - 164 in -
Blade Height - Without Cutting Edge - 23 in -

Service Refill Capacities

Transmission and Differential 9 gal (US) 23.5 gal (US) -
Circle Drive 1.8 gal (US) 1.8 gal (US) -
Fuel Tank 65 gal (US) 109.9 gal (US) -
Cooling System 14 gal (US) 15.9 gal (US) -
Engine Crankcase 4.8 gal (US) - -
Diesel Exhaust Fluid Tank (Tier 4 Only) 5 gal (US) 5.8 gal (US) -
Hydraulic System 25.6 gal (US) 33 gal (US) -

Machine Weight

Lever/Steering Wheel All-Wheel drive (AWD) Weight* Tier 4 36731 lb - -
Note (1) *Typically equipped includes 4267 mm (14 ft) plus blade, tires, push plate, ripper, bottom guard, operator, and full fluids. - -
Joystick Weight* Tier 4 35358 lb - -
Lever/Steering Wheel Weight* Tier 4 35067 lb - -
Joystick All-Wheel Drive (AWD) Weight* Tier 4 36846 lb - -

Blade Range

Blade Tip Range Forward 40 - -
Maximum Shoulder Reach Right 76 in - -
Moldboard Side Shift Right 26.1 in - -
Maximum Shoulder Reach Left 69.4 in - -
Maximum Depth of Cut 30.5 in 23.3 in -
Moldboard Side Shift Left 20.1 in - -
Circle Center Shift Left 26 in - -
Blade Tip Range Backward 5 - -
Maximum Lift Above Ground 16.1 in 16.5 in -
Circle Center Shift Right 26 in - -
Circle Centershift - Left - 25.6 in -
Circle Centershift - Right - 20.5 in -
Blade Tip Range - Backward - -
Maximum Shoulder Reach Outside of Tires - Right - 78.9 in -
Moldboard Sideshift - Right - 31.1 in -
Moldboard Sideshift - Left - 29.1 in -
Maximum Shoulder Reach Outside of Tires - Left - 73.6 in -
Blade Tip Range - Forward - 40° -

Dimensions

Maximum Height 136.4 in - -
Length of Machine* 387 in - -
Width All Wheel Drive (AWD) 2551 mm - -
Width 102 in - -
Note *Typically equipped with push block and ripper. - -
Basic Blade Width 12 ft - -

Air Conditioning System

Air Conditioning The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system con The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton). -

Frame

Circle - Outer Diameter - 71.7 in -
Front Axle - Wheel Lean - Left/Right - 17.1° -
Front Axle - Total Oscillation per Side - 32° -
Add a Similar Product: