Compare

Compare Equipment Go Back

Engine
	D1 Dozer View Product	824 Wheel Dozer View Product Remove	814 Wheel Dozer View Product Remove
Engine Model	Cat C3.6	Cat® C15	Cat® C7.1
Power - Net	80 hp	-	-
Displacement	220 in³	927.6 in³	427.8 in³
Net Power - 2,200 rpm - SAE J1349	80 hp	-	-
Net Power - 2,200 rpm - ISO 9249/EEC 80/1269	80 hp	-	-
Note (1)	Net power is tested per ISO 9249:2007 and SAE J1349:2011 and as advertised is the power available at the ﬂywheel when the engine is equipped with fan, air intake system, exhaust system and alternator.	Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module and alternator.	Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module, and alternator.
Note (2)	All non-road U.S. EPA Tier 4 Final, EU Stage V, Japan 2014 (Tier 4 Final) and Korea Tier 4 Final diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm EPA/10 ppm EU (mg/kg) sulfur or less.	Two engine emission configurations are available. One meets U.S. EPA Tier 4 Final, EU Stage V, Korea Stage V, and Japan 2014 emissions standards. The other meets Brazil MAR-1 emission standards, emitting equivalent to U.S. EPA Tier 3 and EU Stage IIIA.	-
Net Power - SAE J1349:2011	-	405 hp	249 hp
Net Power - ISO 9249:2007	-	405 hp	249 hp
Rated Speed	-	1800 r/min	2200 r/min
Engine Power - ISO 14396:2002	-	426 hp	275 hp
Gross Power - SAE J1995:2014	-	434 hp	286 hp
Peak Net Torque (1,300 rpm)	-	1479 lbf·ft	-
Torque Rise	-	33%	26 %
Maximum Altitude without Derating (U.S. EPA Tier 4 Final/EU Stage V)	-	9298 ft	-
Maximum Altitude without Derating (U.S. EPA Tier 3/EU Stage IIIA)	-	9098 ft	-
Bore	-	5.4 in	4.1 in
Stroke	-	6.7 in	5.3 in
High Idle Speed	-	2300 r/min	2270 r/min
Low Idle Speed	-	800 r/min	800 r/min
Emissions	-	-	Option 2 - Brazil MAR-1, emitting equivalent to U.S. EPA Tier 3/EU Stage IIIA
Peak Torque (1400 rpm)	-	-	902 lbf·ft
Engine Power - ISO 14396: 2002	-	-	275 hp
Peak Torque ( 1,400 rpm )	-	-	749 lbf·ft
Maximum Altitude without Derating	-	-	9842.5 ft
Weights
Operating Weight	17855 lb	-	-
Operating Weight - LGP	18839 lb	-	-
Note (1)	Specifications shown are for machine equipped with dozer blade, EROPS cab, back-up alarm, operator, coolant, lubricants and full fuel tank.	-	-
Operating Weight - LGP, 762 mm/30 in	19295 lb	-	-
Note (2)	For machine with ripper, add 554 kg (1,222 lb).	-	-
Transmission
Drive Pumps	1	-	-
Maximum Travel Speed - Reverse	6.2 mile/h	-	-
Relief Valve Settings	7033 psi	-	-
Maximum Travel Speed - Forward	5.6 mile/h	-	-
Track Motors	2	-	-
Transmission Type	-	Cat planetary - powershift - ECPC	Cat Planetary Power Shift
Forward - 1	-	3.8 mile/h	3.7 mile/h
Forward - 2	-	6.9 mile/h	6.5 mile/h
Forward - 3	-	12.2 mile/h	11.2 mile/h
Forward - 4	-	21.6 mile/h	19.4 mile/h
Reverse - 1	-	4.3 mile/h	4.2 mile/h
Reverse - 2	-	7.8 mile/h	7.3 mile/h
Reverse - 3	-	13.9 mile/h	12.8 mile/h
Reverse - 4	-	24.7 mile/h	22.1 mile/h
Hydraulic Controls
Pump Output	17.2 gpm	-	-
Relief Valve Settings	2988 psi	-	-
Ripper
Type	Parallelogram	-	-
Number of Shanks	3	-	-
Height	6.5 in	-	-
Weight	1222 lb	-	-
Maximum Ground Clearance Under Tip	17.6 in	-	-
Maximum Digging Depth	13.3 in	-	-
Overall Width	67.3 in	-	-
Maximum Reach - Ground Line	30.2 in	-	-
Engine
Power Train	Hydrostatic	-	-
Cab
FOPS	ISO 3449:2005 Level II	-	-
ROPS	ISO 3471:2008	-	-
Undercarriage
Length - Track on Ground - LGP, 762 mm (30 in)	89 in	-	-
Length - Track on Ground - LGP	89 in	-	-
Track Gauge - LGP	68 in	-	-
Shoe Width - LGP, 762 mm (30 in)	30 in	-	-
Track Gauge - LGP, 762 mm (30 in)	73 in	-	-
Shoe Width - LGP	25 in	-	-
Track Gauge	59 in	-	-
Shoe Width - Standard	16 in	-	-
Ground Pressure - LGP	4.3 psi	-	-
Ground Pressure - LGP, 762 mm (30 in)	3.7 psi	-	-
Number of Shoes - Each Side - Sealed and Lubricated Track (SALT) Undercarriage	43	-	-
Number of Rollers - Each Side	6	-	-
Undercarriage
Length of Track on Ground	89 in	-	-
Number of Shoes - Each Side - Abrasion Undercarriage	38	-	-
Ground Pressure	6.45 psi	-	-
Service Refill Capacities
Final Drive - Each - LGP	2.6 gal (US)	-	-
Cooling System	4.2 gal (US)	30.6 gal (US)	-
Diesel Exhaust Fluid (DEF) Tank	4.9 gal (US)	-	-
Transmission - Hydraulic Tank	23.8 gal (US)	-	-
Crankcase - With Filter	2.8 gal (US)	-	-
Fuel Tank	51.5 gal (US)	206.6 gal (US)	132.1 gal (US)
Engine Crankcase	-	9 gal (US)	5.3 gal (US)
Transmission	-	17.4 gal (US)	13.2 gal (US)
Diesel Exhaust Fluid Tank (For Tier 4 Final/Stage V Only)	-	8.5 gal (US)	-
Differential - Final Drives - Front	-	26.4 gal (US)	17.2 gal (US)
Differential - Final Drives - Rear	-	29.1 gal (US)	17.2 gal (US)
Hydraulic Tank Only	-	35.4 gal (US)	19.8 gal (US)
Hydraulic System - Implement/Steering	-	56.5 gal (US)	34.1 gal (US)
Note (1)	-	All nonroad Tier 4 Final, EU Stage V, and Japan 2014 (Tier 4 Final) diesel engines are required to use: – Ultra low sulfur diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. – Cat engines are compatible with the following renewable, alternative	All nonroad Tier 4 Final and EU Stage V diesel engines are required to use: – Ultra low sulfur diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. – Cat engines are compatible with the following renewable, alternative, and biodiesel* fuels that
Diesel Exhaust Fluid Tank	-	-	4.2 gal (US)
Cooling Systems - Tier 4 Final/EU Stage V	-	-	21.4 gal (US)
Cooling Systems - Tier 3/Stage IIIA equivalent	-	-	19.3 gal (US)
Service Refill Capacities
Final Drives - Each Side	2.6 gal (US)	-	-
Air Conditioning System
Air Conditioning	The air conditioning system on this machine contains the ﬂuorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.	The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system co	The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. - If equipped with R134a (Global Warming Potential = 1430), the system con
Dimensions
BLADE: Blade Capacity (SAE) - LGP	2.17 yd³	-	-
BLADE: Blade Lift Height - LGP	28.7 in	-	-
BLADE: Maximum Tilt - LGP	17.2 in	-	-
BLADE: Blade Width - LGP	124 in	-	-
Ground Clearance - LGP	13 in	-	-
BLADE: Blade Width at Maximum Angle - LGP	113.1 in	-	-
BLADE: Digging Depth - LGP	23 in	-	-
Track Gauge - LGP	67.9 in	-	-
Ground Clearance - LGP, 762 mm (30 in)	13 in	-	-
BLADE: Blade Height - LGP	33.8 in	-	-
Overall Length - With Blade - LGP, 762 mm (30 in)	167.8 in	-	-
Track Gauge - LGP, 762 mm (30 in)	73 in	-	-
BLADE: Blade Cutting Edge Angle, Adjustable - LGP	52° to 58°	-	-
BLADE: Maximum Angle (either side) - LGP	25°	-	-
Overall Length - With Blade - LGP	167.8 in	-	-
Note	*Abrasion Undercarriage	-	-
Length of Basic Dozer (without blade) - LGP, 762 mm (30 in)	129.6 in	-	-
Width of Dozer (standard shoes, no blade) - Standard	74.8 in	-	-
Length of Basic Dozer (without blade) - Standard	129.6 in	-	-
Length of Basic Dozer (without blade) - LGP	129.6 in	-	-
Width of Dozer (standard shoes, no blade) - LGP, 762 mm (30 in)	94.9 in	-	-
Dozer Height - LGP	108.9 in	-	-
Width of Dozer (standard shoes, no blade) - LGP	92.9 in	-	-
Dozer Height - LGP, 762 mm (30 in)	108.9 in	-	-
Dozer Height - Standard	108.9 in	-	-
Dimensions
Note	With Ripper Attachment (add to Length of Basic Dozer) - 1177 mm (46.3 in)	-	-
BLADE: Blade Width at Maximum Angle - Standard	95.2 in	-	-
BLADE: Digging Depth - Standard	23.2 in	-	-
BLADE: Blade Width - Standard	104.2 in	-	-
BLADE: Blade Lift Height - Standard	28.7 in	-	-
Ground Clearance - Standard	13 in	-	-
BLADE: Blade Cutting Edge Angle, Adjustable - Standard	52° to 58°	-	-
BLADE: Maximum Angle (either side) - Standard	25°	-	-
BLADE: Maximum Tilt - Standard	14.5 in	-	-
BLADE: Blade Capacity (SAE) - Standard	1.99 yd³	-	-
Track Gauge - Standard	58.9 in	-	-
BLADE: Blade Height - Standard	35.8 in	-	-
Overall Length - With Blade - Standard	168 in	-	-
High Performance Winch
Weight	1345 lb	-	-
Drum diameter	10 in	-	-
Winch drive	Hydrostatic	-	-
Winch length	27.76 in	-	-
Maximum line pull – bare drum	40000 lb	-	-
Maximum line speed – full drum	207 ft/min	-	-
Drum width	10.8 in	-	-
Drum capacity – optional	256 ft	-	-
Rope diameter – recommended	0.63 in	-	-
Maximum line pull – full drum	25000 lb	-	-
Rope diameter – optional	0.75 in	-	-
Speed	Variable	-	-
Maximum line speed – bare drum	131 ft/min	-	-
Throat clearance	6.75 in	-	-
Drum capacity – recommended cable	371 ft	-	-
Overall width	29.2 in	-	-
Control	Hydraulic	-	-
Retrieval Winch
Drum Diameter	8 in	-	-
Drum Width	9.65 in	-	-
Throat Clearance	5.6 in	-	-
Winch Length	35.63 in	-	-
Overall width	27.91 in	-	-
Weight	1747 lb	-	-
Maximum Line Pull - Full Drum	79 ft/min	-	-
Drum Capacity - Recommended Cable	277 ft	-	-
Maximum Line Pull - Bare Drum	50 ft/min	-	-
Drum Capacity - Optional Cable	195 ft	-	-
Maximum Line Speed - Full Drum	20350 lb	-	-
Control	Hydraulic	-	-
Maximum Line Speed - Bare Drum	32150 lb	-	-
Rope Diameter - Optional	0.75 in	-	-
Winch Drive	Hydraulic	-	-
Rope Diameter - Recommended	0.63 in	-	-
Speed	Variable	-	-
Operating Specifications
Operating Weight – Straight Blade (Tier 4 Final/Stage V)	-	74966 lb	-
Blade Capacity Range	-	5.1-16.2 m3 (6.6-21.2 yd3)	-
Operating Weight (Tier 4 Final/Stage V)	-	-	48526 lb
Operating Weight (Tier 3/Stage IIIA equivalent)	-	-	47887 lb
Hydraulic System - Lift/Tilt
Pump Flow at 1,800 rpm	-	30.9 gpm	-
Main Relief Pressure	-	3771 psi	-
Maximum Supply Pressure	-	3495 psi	-
Cylinders, Double Acting - Lift, Bore and Stroke	-	120 mm × 1070 mm (4.7 in × 42.1 in)	120 mm × 915 mm (4.7 in × 36.0 in)
Cylinder, Double Acting - Tilt and Tip, Bore and Stroke	-	140 mm × 230 mm (5.5 in × 9.1 in)	-
Lift/Tilt System - Circuit	-	-	Pilot operated load sensing valve with EH
Lift/Tilt System	-	-	Variable displacement piston
Maximum Flow at 2,200 rpm	-	-	23.5 gpm
Relief Valve Setting - Lift/Tilt	-	-	3190 psi
Cylinders, Double Acting - Left and Right Tilt, Bore and Stroke	-	-	101.6 mm × 234 mm (4.0 in × 9.2 in)
Pilot System	-	-	Open center, fixed displacement gear
Pilot Relief Valve Setting	-	-	3046 psi
Hydraulic System - Steering
Steering System - Circuit	-	Pilot operated, load sensing	Pilot, load sensing
Bore	-	4.5 in	-
Stroke	-	22.7 in	-
Steering System - Pump	-	Variable displacement piston	Variable displacement piston
Max Flow at 1,800 rpm	-	44.9 gpm	-
Relief Valve Setting - Steering	-	3481 psi	4003 psi
Vehicle Articulation Angle	-	86°	-
Maximum Flow at 2,200 rpm	-	-	38.8 gpm
Total Steering Angle	-	-	72°
Steering Cycle Times - High Idle	-	-	3 s
Steering Cycle Times - Low Idle	-	-	8.2 s
Axles
Front	-	Planetary – Fixed	Planetary – Fixed
Rear	-	Planetary – Oscillating	Planetary – Oscillating
Oscillation Angle	-	±11°	±10°
Braking System
Parking Brake	-	Drum and shoe, spring applied, hydraulic released	Drum and Shoe, Spring Applied, Hydraulic Released
Brakes	-	Multi-disc wet (enclosed) 4 WHL	-
Service Brakes	-	-	Single Disc Wet (enclosed) 4 WHL
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)	-	73 dB(A)	72 dB(A)
Machine Sound Power Level (ISO 6395:2008)	-	113 dB(A)	111 dB(A)
Operator Sound Pressure Level (ISO 6396:2008)*	-	72 dB(A)	70 dB(A)
Machine Sound Power Level (ISO 6395:2008)**	-	110 dB(A)	-
Note (1)	-	* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”	* Sound suppression equipped
Note (2)	-	** European Union Directive “2000/14/EC” as amended by “2005/88/EC.” and UK Noise Regulation 2001 No. 1701	The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at maximum engine cooling fan speed.
Note (3)	-	The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.	The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at maximum engine cooling fan speed.
Note (4)	-	The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.	Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Note (5)	-	Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.	-
Machine Sound Power Level (ISO 6395:2008)*	-	-	109 dB(A)
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)	-	73 dB(A)	72 dB(A)
Machine Sound Power Level (ISO 6395:2008)	-	113 dB(A)	112 dB(A)
Operator Sound Pressure Level (ISO 6396:2008)*	-	72 dB(A)	70 dB(A)
Machine Sound Power Level (ISO 6395:2008)**	-	110 dB(A)	-
Note (1)	-	* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”	* Sound suppression equipped
Note (2)	-	** European Union Directive “2000/14/EC” as amended by “2005/88/EC.” and UK Noise Regulation 2001 No. 1701	The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at maximum engine cooling fan speed.
Note (3)	-	The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.	The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at maximum engine cooling fan speed.
Note (4)	-	The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.	Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Note (5)	-	Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.	-
Machine Sound Power Level (ISO 6395:2008)*	-	-	110 dB(A)
Dimensions (Approximate)
Height to Top of Beacon	-	14.5 ft	13.1 ft
Height - Top of Exhaust Stack	-	14.2 ft	-
Height - Top of Hood	-	10.5 ft	8.7 ft
Ground Clearance - Bumper	-	2.8 ft	-
Centerline of Rear Axle to Edge of Bumper	-	9.3 ft	-
Centerline of Front Axle to Hitch	-	6.1 ft	5.5 ft
Wheel Base	-	12.1 ft	11 ft
Length - With Blade on Ground - Straight Blade	-	27.6 ft	-
Ground Clearance to Trunnion	-	1.45 ft	-
Height - Top of Cab	-	13.5 ft	12.1 ft
Width Over Guardrails	-	10.94 ft	-
Ground Clearance	-	1.8 ft	-
Height - Top of Exhaust Pipe	-	-	11.3 ft
Height to Top of Radiator Guard	-	-	8 ft
Ground Clearance to Hitch	-	-	1.4 ft
Ground Clearance to Transmission Guard	-	-	1.4 ft
Ground Clearance to Bottom of Bumper	-	-	2.3 ft
Centerline of Rear Axle to Bumper	-	-	6.5 ft
Width over Platform	-	-	10.3 ft
Overall Length to Front Tire	-	-	21 ft
Overall Machine Length with Straight Blade	-	-	23.6 ft
Overall Machine Length with Coal Blade	-	-	25.5 ft
Straight Blade
Capacity	-	6.6 yd³	3.72 yd³
Width Over End Bits	-	177.4 in	-
Height	-	48.4 in	3.3 ft
Dig Depth	-	17.6 in	1.6 ft
Ground Clearance	-	41.6 in	3 ft
Maximum Tilt	-	45.9 in	2.6 ft
Turning Radius – Outside Corner of Blade	-	23.7 ft	23.5 ft
Turning Radius – Inside Corner of Blade	-	10.15 ft	11.6 ft
Overall Width	-	-	12 ft
Weight	-	-	3000 lb
Total Operating Weight	-	-	48526 lb
Straight Push Plate Blade
Capacity	-	6.6 yd³	-
Width Over End Bits	-	177.4 in	-
Height	-	48.4 in	-
Dig Depth	-	17.6 in	-
Ground Clearance	-	41.6 in	-
Maximum Tilt	-	45.9 in	-
Turning Radius – Outside Corner of Blade	-	23.2 ft	-
Turning Radius – Inside Corner of Blade	-	10.2 in³	-
Semi-Universal Blade
Capacity	-	10 yd³	-
Width Over End Bits	-	174.1 in	-
Height	-	61.1 in	-
Dig Depth	-	18.8 in	-
Ground Clearance	-	42 in	-
Maximum Tilt	-	44.1 in	-
Turning Radius – Outside Corner of Blade	-	23.8 ft	-
Turning Radius – Inside Corner of Blade	-	10.8 ft	-
Universal Blade
Capacity	-	10 yd³	-
Width Over End Bits	-	171.3 in	-
Height	-	53.1 in	-
Dig Depth	-	18.1 in	-
Ground Clearance	-	41.4 in	-
Maximum Tilt	-	44.6 in	-
Turning Radius – Outside Corner of Blade	-	23.9 ft	-
Turning Radius – Inside Corner of Blade	-	11.3 ft	-
Coal Blade
Capacity	-	21.2 yd³	13.8 yd³
Width Over End Bits	-	189 in	-
Height	-	68.7 in	4.8 ft
Dig Depth	-	18.6 in	1.6 ft
Ground Clearance	-	42.2 in	3.1 ft
Maximum Tilt	-	48.9 in	3.1 ft
Turning Radius – Outside Corner of Blade	-	24.9 ft	25.1 ft
Turning Radius – Inside Corner of Blade	-	11.4 ft	11.2 ft
Overall Width	-	-	14.2 ft
Weight	-	-	4429 lb
Total Operating Weight	-	-	49996 lb
Extended Wear Blade
Capacity	-	10.6 yd³	-
Width Over End Bits	-	171.6 in	-
Height	-	53.1 in	-
Dig Depth	-	18.1 in	-
Ground Clearance	-	41.4 in	-
Maximum Tilt	-	44.6 in	-
Turning Radius – Outside Corner of Blade	-	23.9 ft	-
Turning Radius – Inside Corner of Blade	-	11.4 ft	-

Compare Equipment Go Back

D1 Dozer

824 Wheel Dozer

814 Wheel Dozer

Engine

Weights

Transmission

Hydraulic Controls

Ripper

Engine

Cab

Undercarriage

Undercarriage

Service Refill Capacities

Service Refill Capacities

Air Conditioning System

Dimensions

Dimensions

High Performance Winch

Retrieval Winch

Operating Specifications

Hydraulic System - Lift/Tilt

Hydraulic System - Steering

Axles

Braking System

Sound Performance - Tier 4 Final / Stage V

Sound Performance - Tier 3 / Stage IIIA

Dimensions (Approximate)

Straight Blade

Straight Push Plate Blade

Semi-Universal Blade

Universal Blade

Coal Blade

Extended Wear Blade

Earthmoving

Parts & Service

Power Systems

Technology

Contact Us