Three engine emission options are available: 1. Meets U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 emission standards. 2. Meets Brazil MAR-1 emission standards, equivalent to U.S. EPA Tier 3 and EU Stage IIIA. 3. Meets China Nonroad Stage IV emissio
-
-
Note (2)
Net power advertised is the power available at the flywheel when the engine is equipped with fan at minimum speed, air intake system, exhaust system, and alternator.
-
-
Maximum Gross Power
-
42 hp
-
Gross Power
-
42 hp
-
Net Power - 2,200 rpm - SAE J1349 R-ing
-
40 hp
-
Net Power - 2,200 rpm - ISO 9249 R-ing
-
40 hp
-
Note
-
*Engine meets U.S. EPA Tier 4 Final emission standards.
-
Operating Specifications
Operating Weight
112574 lb
-
-
Bucket Capacity Range
4.7-13 m3 (6.2-17 yd3)
-
-
Rated Payload - Quarry Face
12.5 t
-
-
Rated Payload - Loose Material
16 t
-
-
Cat Truck Match - Standard
770 - 772
-
-
Cat Truck Match - High Lift
773 - 775
-
-
Transmission
Transmission Type
Cat planetary powershift
-
-
Forward - 1
4 mile/h
-
-
Forward - 2
7.2 mile/h
-
-
Forward - 3
12.7 mile/h
-
-
Forward - 4
21.6 mile/h
-
-
Reverse - 1
4.7 mile/h
-
-
Reverse - 2
8.3 mile/h
-
-
Reverse - 3
14.4 mile/h
-
-
Direct Drive - Forward 1
Lock-up disabled
-
-
Direct Drive - Forward 2
7.8 mile/h
-
-
Direct Drive - Forward 3
13.9 mile/h
-
-
Direct Drive - Forward 4
24.4 mile/h
-
-
Direct Drive - Reverse 1
5 mile/h
-
-
Direct Drive - Reverse 2
8.9 mile/h
-
-
Direct Drive - Reverse 3
15.8 mile/h
-
-
Travel Speed
-
12.4 mile/h
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
EH- Positive Flow Control, Flow Sharing
-
-
Lift/Tilt System - Pump
Variable displacement piston
-
-
Maximum Flow at 1,400-1,860 rpm
153 gpm
-
-
Relief Valve Setting - Lift/Tilt
4757 psi
-
-
Cylinders, Double Acting - Lift, Bore and Stroke
210 mm × 1050 mm (8.7 in × 41.3 in)
-
-
Cylinders, Double Acting - Tilt, Bore and Stroke
266 mm × 685 mm (8.7 in × 27 in)
-
-
Pilot System
Variable displacement piston
-
-
Relief Valve Setting - Main
551 psi
-
-
Hydraulic Cycle Time (1,400-1,860 rpm)
Rack Back
4.5 s
-
-
Raise
8 s
-
-
Dump
2.2 s
-
-
Lower Float Down
3.5 s
-
-
Total Hydraulic Cycle Time - Empty Bucket
18.2 s
-
-
Hydraulic System - Steering
Steering System - Circuit
Pilot, load sensing
-
-
Steering System - Pump
Piston, variable displacement
-
-
Maximum Flow at 1,400-1,600 rpm
71.3 gpm
-
-
Relief Valve Setting - Steering
4351 psi
-
-
Total Steering Angle
86 °
-
-
Steering Cycle Times - High Idle
3.4 s
-
-
Steering Cycle Times - Low Idle
5.6 s
-
-
Air Conditioning System
Air Conditioning
• The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. • If equipped with R134a (Global Warming Potential = 1430), the system
-
-
Axles
Front
Fixed
-
-
Rear
Trunnion
-
-
Oscillation Angle
13 °
-
-
Brakes
Brakes
ISO 3450:2011
-
-
Operator's Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
-
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
73 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
111 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
109 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives.”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701.
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
73 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
112 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
110 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives.”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701.
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Service Refill Capacities
Fuel Tank
188 gal (US)
11.4 gal (US)
-
Cooling System
31.7 gal (US)
3 gal (US)
-
Coolant (Validated by Test Cell Fill Quantities)
33 gal (US)
-
-
Crankcase
15.9 gal (US)
-
-
Diesel Exhaust Fluid Tank (For Tier 4 Final/Stage V Only)
8.7 gal (US)
-
-
Transmission
24.3 gal (US)
-
-
Transmission - Validated by Test Cell Fill Quantities
29 gal (US)
-
-
Differential - Final Drives - Front
49.1 gal (US)
-
-
Differential - Final Drives - Rear
49.1 gal (US)
-
-
Hydraulic System Factory Fill
125.5 gal (US)
-
-
Hydraulic System - Tank Only
63.4 gal (US)
-
-
Note
• All non-road Tier 4 Final/Stage V diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels** up to: – 20% biodiesel FAME (fatty acid methyl ester
-
-
Hydraulic System
-
6.3 gal (US)
-
Engine Oil
-
2.4 gal (US)
-
Dimensions (Approximate) - Standard Lift Linkage
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
14 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
39.3 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Clearance at Maximum Lift
11.9 ft
-
-
B-Pin Height - Maximum Lift
18 ft
-
-
Maximum Overall Height - Bucket Raised
24.5 ft
-
-
Reach - Maximum Lift
6.5 ft
-
-
Dimensions (Approximate) - High Lift Linkage
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
15.3 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
40.7 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Clearance at Maximum Lift
13.3 ft
-
-
B-Pin Height - Maximum Lift
19.3 ft
-
-
Maximum Overall Height - Bucket Raised
25.8 ft
-
-
Reach - Maximum Lift
6.8 ft
-
-
Weights
Operating Weight
-
9414 lb
-
Buckets
Bucket Capacities
-
0.6-1.0 m3 (0.8-1.3 yd3)
-
Bucket Capacities - General Purpose
-
0.6 m3 (0.8 yd3)
-
Bucket Capacities - Light Material
-
1.0 m3 (1.3 yd3)
-
Hydraulic System
Main Relief
-
3481 psi
-
3rd Auxiliary Flow
-
14 gpm
-
Hydraulic Cycle Time - Lower, Float
-
2.4 s
-
Loader Hydraulic System
Hydraulic Cycle Time - Lift
-
4.4 s
-
Hydraulic Cycle Time - Dump
-
0.7 s
-
Cab
ROPS
-
ISO 3471:2008
-
FOPS
-
ISO 3449:2005 Level I
-
Dimensions (Approximate) - Standard Lift
Cab Height
-
8.25 ft
-
Ground Clearance
-
10 in
-
Wheel Base
-
6.42 ft
-
Overall Length - With Bucket*
-
15.75 ft
-
Reach at Maximum Dump Height*
-
2.33 ft
-
Dig Depth
-
6 in
-
Maximum Dump Height*
-
7.5 ft
-
Load Over Height
-
9.17 ft
-
Hinge Pin at Maximum Height
-
10.08 ft
-
Departure Angle - Degrees
-
30°
-
Overall Length - With Forks
-
17.08 ft
-
Reach - Ground Level
-
2.67 ft
-
Maximum Reach
-
4.5 ft
-
Fork Depth Above Ground
-
2 in
-
Fork Height at Maximum Reach
-
4.67 ft
-
Maximum Fork Height
-
9.83 ft
-
Fork Reach at Maximum Height
-
2 ft
-
Turning Radius - Over Bucket*
-
13.17 ft
-
Turning Radius - Inside Tire**
-
5.92 ft
-
Width - Over Bucket*
-
5.83 ft
-
Tire Gauge
-
4.33 ft
-
Machine Width**
-
5.58 ft
-
Articulation Angle
-
40°
-
Steering Angle
-
80°
-
Dump Angle at Maximum Height
-
40°
-
Note (1)
-
*Vary with bucket size.
-
Note (2)
-
**Vary with tire size.
-
Note (3)
-
Dimensions listed are based on the machine configured with cab with air conditioning, remote quick coupler, general purpose bucket or 1067 mm (42 in) forks, 75 kg (165 lb) operator, 33 × 15.5-16.5, 12 PR tires, without ride control, without precleaner.
-
Dimensions (Approximate) - High Lift
Cab Height
-
8.25 ft
-
Ground Clearance
-
10 in
-
Wheel Base
-
6.42 ft
-
Overall Length - With Bucket*
-
16.17 ft
-
Reach at Maximum Dump Height*
-
2.42 ft
-
Dig Depth
-
8 in
-
Maximum Dump Height*
-
8 ft
-
Load Over Height
-
9.67 ft
-
Hinge Pin at Maximum Height
-
10.58 ft
-
Departure Angle - Degrees
-
30°
-
Overall Length - With Forks
-
17.58 ft
-
Reach - Ground Level
-
3.25 ft
-
Maximum Reach
-
4.92 ft
-
Fork Depth Above Ground
-
2 in
-
Fork Height at Maximum Reach
-
4.67 ft
-
Maximum Fork Height
-
10.33 ft
-
Fork Reach at Maximum Height
-
2 ft
-
Turning Radius - Over Bucket*
-
13.42 ft
-
Turning Radius - Inside Tire**
-
5.92 ft
-
Width - Over Bucket*
-
5.83 ft
-
Tire Gauge
-
4.33 ft
-
Machine Width**
-
5.58 ft
-
Articulation Angle
-
40°
-
Steering Angle
-
80°
-
Dump Angle at Maximum Height
-
40°
-
Note (1)
-
*Vary with bucket size.
-
Note (2)
-
**Vary with tire size.
-
Note (3)
-
Dimensions listed are based on the machine configured with cab with air conditioning, remote quick coupler, general purpose bucket or 1067 mm (42 in) forks, 75 kg (165 lb) operator, 33 × 15.5-16.5, 12 PR tires, without ride control, without precleaner.
-
Operating Specifications - Standard Lift
Tire Size
-
33 × 15.5-16.5, 12 PR
-
Rated Bucket Capacity
-
0.8 yd³
-
Breakout Force
-
6160 lbf
-
Operating Weight
-
9414 lb
-
Rated Operating Load at Full Turn - Bucket***
-
2701 lb
-
Straight Tipping Load - Bucket***
-
6415 lb
-
Full Turn Static Tipping Load - Bucket (ISO 14397-1*)***
-
5401 lb
-
Full Turn Static Tipping Load - Bucket (Rigid Tire**)***
-
5512 lb
-
Rack Back - Transport Position
-
51°
-
Rated Operating Load at Full Turn - Forks (EN 474-3:2006, Firm and Level Ground, 500 mm [20 in] Load Center) (80% FTSTL)***
-
3366 lb
-
Rated Operating Load at Full Turn - Forks (EN 474-3:2006, Rough Terrain, 500 mm [20 in] Load Center) (60% FTSTL)***
-
2524 lb
-
Note (1)
-
*Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification be-tween calculation and testing.
-
Note (2)
-
**Compliance to ISO 14397-1 (2007) Sections 1 thru 5.
-
Note (3)
-
***Manual quick coupler, precleaner hood.
-
Note (4)
-
Operating specifications shown are based on machine equipped with enclosed ROPS cab with air conditioning, remote quick coupler, 75 kg (165 lb) operator and general purpose bucket (GP), without ride control, without precleaner unless otherwise noted.
-
Operating Specifications - High Lift
Tire Size
-
33 × 15.5-16.5, 12 PR
-
Rated Bucket Capacity
-
0.8 yd³
-
Breakout Force
-
6204 lbf
-
Operating Weight
-
9462 lb
-
Rated Operating Load at Full Turn - Bucket***
-
2502 lb
-
Straight Tipping Load - Bucket***
-
5975 lb
-
Full Turn Static Tipping Load - Bucket (ISO 14397-1*)***
-
5004 lb
-
Full Turn Static Tipping Load - Bucket (Rigid Tire**)***
-
5115 lb
-
Rack Back - Transport Position
-
51°
-
Rated Operating Load at Full Turn - Forks (EN 474-3:2006, Firm and Level Ground, 500 mm [20 in] Load Center) (80% FTSTL)***
-
3148 lb
-
Rated Operating Load at Full Turn - Forks (EN 474-3:2006, Rough Terrain, 500 mm [20 in] Load Center) (60% FTSTL)***
-
2361 lb
-
Note (1)
-
*Full compliance to ISO 14397-1 (2007) Sections 1 thru 6, which requires 2% verification be-tween calculation and testing.
-
Note (2)
-
**Compliance to ISO 14397-1 (2007) Sections 1 thru 5.
-
Note (3)
-
***Manual quick coupler, precleaner hood.
-
Note (4)
-
Operating specifications shown are based on machine equipped with enclosed ROPS cab with air conditioning, remote quick coupler, 75 kg (165 lb) operator and general purpose bucket (GP), without ride control, without precleaner unless otherwise noted.
-
Maximum Material Densities - General Purpose
Bucket Type
-
General Purpose
-
Rated Capacity
-
0.8 yd³
-
Dump Height
-
90 in
-
Maximum Material Density
-
3169 lb/yd³
-
Bucket Width
-
70 in
-
Note
-
Based on ISO 7546:1983 and rated operating loads at full turn and standard linkage.
-
Maximum Material Densities - Light Material
Bucket Type
-
Light Material
-
Rated Capacity
-
1.3 yd³
-
Dump Height
-
85 in
-
Maximum Material Density
-
1989 lb/yd³
-
Bucket Width
-
74 in
-
Note
-
Based on ISO 7546:1983 and rated operating loads at full turn and standard linkage.
