Two engine emissions options are available: 1. Meets U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 emission standards. 2. Meets Brazil MAR-1 emission standards, equivalent to U.S. EPA Tier 3 and EU Stage IIIA.
-
-
Note (2)
Net power advertised is the power available at the flywheel when the engine is equipped with fan at minimum speed, air intake system, exhaust system, and alternator.
-
-
Net Power - ISO 9249
-
225 hp
-
Emissions
-
Tier 4/Stage V
-
Note
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.9 kg (4.2 lb) of refrigerant which has a CO2 equivalent of 2.717 metric tonnes (2.995 tons).
-
Maximum Net Power - 1,700 rpm - ISO 9249 - Metric
-
228 hp
-
Maximum Power - 1,700 rpm - ISO 14396
-
240 hp
-
Maximum Power - 1,700 rpm - ISO 14396 - Metric
-
243 hp
-
Peak Gross Torque - 1,400 rpm - SAE J1995
-
811 ft·lbf
-
Peak Gross Torque - 1,400 rpm - ISO 14396
-
805 ft·lbf
-
Maximum Net Power - 1,700 rpm - ISO 9249
-
225 hp
-
Maximum Net Power - 1,700 rpm - SAE J1349
-
225 hp
-
Maximum Power - 1,700 rpm - SAE J1995
-
241 hp
-
Operating Specifications
Operating Weight
116362 lb
-
-
Bucket Capacity Range
4.7-13 m3 (6.2-17 yd3)
-
-
Rated Payload - Quarry Face
12.5 t
-
-
Rated Payload - Loose Material
16 t
-
-
Transmission
Transmission Type
Cat switched reluctance electric drive
-
-
Forward 1 (virtual)
4.3 mile/h
-
-
Forward 2 (virtual)
7 mile/h
-
-
Forward 3 (virtual)
13.8 mile/h
-
-
Forward 4 (virtual)
20 mile/h
-
-
Reverse 1 (virtual)
4.3 mile/h
-
-
Reverse 2 (virtual)
7 mile/h
-
-
Reverse 3 (virtual)
17.5 mile/h
-
-
Note
-
Maximum travel speed in standard vehicle with empty bucket and standard L3 tires with 760 mm (30 in) roll radius.
-
Reverse - 3
-
14.2 mile/h
-
Forward - 3
-
14.2 mile/h
-
Forward - 1
-
4.5 mile/h
-
Forward - 2
-
8 mile/h
-
Forward - 4
-
22.4 mile/h
-
Reverse - 2
-
8 mile/h
-
Reverse - 1
-
4.5 mile/h
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
EH-Positive Flow Control, Flow Sharing
-
-
Lift/Tilt System - Pump
Variable displacement piston
-
-
Maximum Flow at 1,400-1,600 rpm
153 gpm
-
-
Relief Valve Setting - Lift/Tilt
4757 psi
-
-
Lift Cylinder - Bore
8.7 in
-
-
Lift Cylinder - Stroke
41.3 in
-
-
Tilt Cylinder - Bore
8.7 in
-
-
Tilt Cylinder - Stroke
27 in
-
-
Hydraulic Cycle Times
Rack Back
4.5 s
-
-
Raise
8 s
-
-
Dump
2.2 s
-
-
Lower Float Down
3.5 s
-
-
Total Hydraulic Cycle Time
18.2 s
-
-
Hydraulic System - Steering
Steering System - Circuit
Pilot, load sensing
-
-
Steering System - Pump
Piston, variable displacement
-
-
Maximum Flow at 1,400-1,600 rpm
71.3 gpm
-
-
Steering Cut Off Pressure
4351 psi
-
-
Total Steering Angle
86°
-
-
Steering Cycle Times - High Idle
3.4 s
-
-
Steering Cycle Times - Low Idle
5.6 s
-
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. • If equipped with R134a (Global Warming Potential = 1430), the system con
-
-
Axles
Front
Fixed
-
-
Rear
Trunnion
-
-
Oscillation Angle
13°
-
-
Brakes
Brakes
ISO 3450:2011
-
-
Operator's Cab
ROPS/FOPS
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
-
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
109 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
109 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
110 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
110 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Service Refill Capacities
Fuel Tank
147 gal (US)
-
-
Cooling System - Jacket Water
30 gal (US)
-
-
Cooling Systems - Power Train
8 gal (US)
-
-
Engine Crankcase
16 gal (US)
-
-
Diesel Exhaust Fluid Tank
8.7 gal (US)
-
-
Transmission
16 gal (US)
11.9 gal (US)
-
Differential - Final Drives - Front
49 gal (US)
10.6 gal (US)
-
Differential - Final Drives - Rear
49 gal (US)
10 gal (US)
-
Hydraulic System - Implement/Steering
126 gal (US)
-
-
Note
Cat U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) and are compatible* with ULSD blended with the following lower-carbon intensity fuels** up to: • 20%
-
-
DEF Tank
-
4.2 gal (US)
-
Fuel Tank Size
-
76.6 gal (US)
-
Cooling System
-
13.2 gal (US)
-
Crankcase
-
4.8 gal (US)
-
Hydraulic Tank
-
29.6 gal (US)
-
Dimensions (Approximate) - Standard Lift
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
14 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
39.3 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Axles
3.2 ft
-
-
Clearance at Maximum Lift
11.9 ft
-
-
B-Pin Height - Maximum Lift
18 ft
-
-
Maximum Overall Height - Bucket Raised
24.5 ft
-
-
Reach - Maximum Lift
6.5 ft
-
-
Note
Specifications are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
-
-
Dimensions (Approximate) - High Lift
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
15.3 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
40.7 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Axles
3.2 ft
-
-
Clearance at Maximum Lift
13.3 ft
-
-
B-Pin Height - Maximum Lift
19.3 ft
-
-
Maximum Overall Height - Bucket Raised
25.8 ft
-
-
Reach - Maximum Lift
6.8 ft
-
-
Note
Specifications are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
-
-
Dimensions - Millyard Linkage
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
13.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Fork Tip
16.5 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
41.9 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Front Axle
3.2 ft
-
-
Fork Height with Level Arms
8.1 ft
-
-
Fork Top Clamp Opening
13.1 ft
-
-
Fork Height at Maximum Lift
17.2 ft
-
-
Hinge Pin Height at Maximum Lift
16.1 ft
-
-
Dump Angle at Maximum Lift
-39.4 °
-
-
Weights
Operating Weight
-
41554 lb
-
Buckets
Bucket Capacities
-
2.9-4.4 m³ (3.75-5.75 yd³)
-
Sound
With Cooling Fan Speed at Maximum Value - Exterior Sound Pressure Level (SAE J88:2013)
-
76 dB(A)*
-
Note (1)
-
*Distance of 15 m (49.2 ft), moving forward in second gear ratio.
-
With Cooling Fan Speed at 70% of Maximum Value: Note (2)
-
European Union Directive "2000/14/EC" as amended by "2005/88/EC."
-
With Cooling Fan Speed at 70% of Maximum Value - Operator Sound Pressure Level (ISO 6396:2008)**
-
73 dB(A)
-
With Cooling Fan Speed at 70% of Maximum Value: Note (1)
-
For machines in European Union countries and in countries that adopt the EU Directives
-
With Cooling Fan Speed at Maximum Value - Note
-
Distance of 15 m (49.2 ft), moving forward in second gear ratio.
-
With Cooling Fan Speed at 70% of Maximum Value - Exterior Sound Power Level (ISO 6395:2008)**
-
107 LWA***
-
Note (3)
-
***European Union Directive "2000/14/EC" as amended by "2005/88/EC."
-
Note (2)
-
**For machines in European Union countries and in countries that adopt the "EU Directives."
-
With Cooling Fan Speed at Maximum Value - Operator Sound Pressure Level (ISO 6396:2008)
-
73 dB(A)
-
With Cooling Fan Speed at Maximum Value - Exterior Sound Power Level (ISO 6395:2008)
-
109 dB(A)
-
Dimensions
Rack Back - Ground
-
40 degrees
-
Height - Top of Exhaust Pipe
-
11.17 ft
-
Centerline of Rear Axle to Hitch
-
5.42 ft
-
Lift Arm Clearance
-
12 ft
-
B-Pin Height
-
13.75 ft
-
Centerline of Rear Axle to Edge of Counterweight
-
6.75 ft
-
Ground Clearance
-
1.5 ft
-
Rack Back - Maximum Lift
-
60 degrees
-
Height - Top of Hood
-
8.75 ft
-
Wheel Base
-
10.83 ft
-
Height - Top of ROPS
-
11.33 ft
-
Rack Back - Carry
-
45 degrees
-
Note
-
All dimensions are approximate and based on MAXAM MS302 23.5R25 L3 radial tires.
-
Weights and Operating Specifications
Note (2)
-
*Full compliance to ISO (2007) 14397-1 Sections 1 thru 6, which requires 2% verification between calculations and testing.
-
Tipping Load - Full Turn - Rigid Tires**
-
25875 lb
-
Breakout Force
-
34638 lbf
-
Tipping Load - Full Turn - ISO 14397-1*
-
24264 lb
-
Note (3)
-
**Compliance to ISO (2007) 14397-1 Sections 1 thru 5.
-
Operating Weight
-
41554 lb
-
Note (1)
-
For 3.1 m3 (4.0 yd3) general purpose buckets with BOCE. Weight based on a machine configuration with MAXAM MS302 23.5R25 L3 radial tires, full fluids, operator, standard counterweight, cold start, roading fenders, Product Link™, secondary steering, sound
-
Hydraulic System
Hydraulic Cycle Time - Total Cycle Time
-
9.4 s
-
Steering System - Pump Type
-
Piston
-
Implement System - Maximum Operating Pressure @ 50 ± 1.5 L/min (13.2 + 0.4 gal/min)
-
4047 psi
-
Implement System - Maximum Pump Output at 2,390 rpm
