Two engine emissions options are available: 1. Meets U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 emission standards. 2. Meets Brazil MAR-1 emission standards, equivalent to U.S. EPA Tier 3 and EU Stage IIIA.
-
-
Note (2)
Net power advertised is the power available at the flywheel when the engine is equipped with fan at minimum speed, air intake system, exhaust system, and alternator.
-
-
Maximum Gross Power
-
110 hp
-
Rated Net Power - Rated Engine Speed
-
2200 r/min
-
Maximum Gross Power - Rated Engine Speed
-
1800 r/min
-
Rated Net Power - SAE J1349
-
99 hp
-
Maximum Gross Power - ISO 14396 (metric)
-
112 hp
-
Rated Net Power - ISO 9249
-
98 hp
-
Maximum Gross Torque - SAE J1995
-
335 ft·lbf
-
Maximum Gross Torque - ISO 14396
-
332 ft·lbf
-
Maximum Net Torque - SAE J1349
-
329 ft·lbf
-
Maximum Net Torque - ISO 9249
-
327 ft·lbf
-
Emissions
-
Engine meets Tier 4 Final/Stage V emission standards.
-
Note
-
Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
-
Maximum Gross Power - ISO 14396
-
110 hp
-
Operating Specifications
Operating Weight
116362 lb
-
-
Bucket Capacity Range
4.7-13 m3 (6.2-17 yd3)
-
-
Rated Payload - Quarry Face
12.5 t
-
-
Rated Payload - Loose Material
16 t
-
-
Transmission
Transmission Type
Cat switched reluctance electric drive
-
-
Forward 1 (virtual)
4.3 mile/h
-
-
Forward 2 (virtual)
7 mile/h
-
-
Forward 3 (virtual)
13.8 mile/h
-
-
Forward 4 (virtual)
20 mile/h
-
-
Reverse 1 (virtual)
4.3 mile/h
-
-
Reverse 2 (virtual)
7 mile/h
-
-
Reverse 3 (virtual)
17.5 mile/h
-
-
Note
-
*Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
-
Forward and Reverse - Speed Range 3
-
25 mile/h
-
Forward and Reverse - Speed Range 2*
-
12.5 mile/h
-
Forward and Reverse - Speed Range 1*
-
6.3 mile/h
-
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit
EH-Positive Flow Control, Flow Sharing
-
-
Lift/Tilt System - Pump
Variable displacement piston
-
-
Maximum Flow at 1,400-1,600 rpm
153 gpm
-
-
Relief Valve Setting - Lift/Tilt
4757 psi
-
-
Lift Cylinder - Bore
8.7 in
-
-
Lift Cylinder - Stroke
41.3 in
-
-
Tilt Cylinder - Bore
8.7 in
-
-
Tilt Cylinder - Stroke
27 in
-
-
Hydraulic Cycle Times
Rack Back
4.5 s
-
-
Raise
8 s
-
-
Dump
2.2 s
-
-
Lower Float Down
3.5 s
-
-
Total Hydraulic Cycle Time
18.2 s
-
-
Hydraulic System - Steering
Steering System - Circuit
Pilot, load sensing
-
-
Steering System - Pump
Piston, variable displacement
-
-
Maximum Flow at 1,400-1,600 rpm
71.3 gpm
-
-
Steering Cut Off Pressure
4351 psi
-
-
Total Steering Angle
86°
-
-
Steering Cycle Times - High Idle
3.4 s
-
-
Steering Cycle Times - Low Idle
5.6 s
-
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a or R1234yf. See the label or instruction manual for identification of the gas. • If equipped with R134a (Global Warming Potential = 1430), the system con
ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
-
-
Sound Performance - Tier 4 Final / Stage V
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
109 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
109 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Sound Performance - Tier 3 / Stage IIIA
Operator Sound Pressure Level (ISO 6396:2008)
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)
110 dB(A)
-
-
Operator Sound Pressure Level (ISO 6396:2008)*
72 dB(A)
-
-
Machine Sound Power Level (ISO 6395:2008)**
110 dB(A)
-
-
Note (1)
* For machines in European Union countries and in countries that adopt the “EU Directives” and “UK Directives”
-
-
Note (2)
** European Union Directive “2000/14/EC” as amended by “2005/88/EC” and UK Noise Regulation 2001 No. 1701
-
-
Note (3)
The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (4)
The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70% of the maximum engine cooling fan speed.
-
-
Note (5)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
-
-
Service Refill Capacities
Fuel Tank
147 gal (US)
43.6 gal (US)
-
Cooling System - Jacket Water
30 gal (US)
-
-
Cooling Systems - Power Train
8 gal (US)
-
-
Engine Crankcase
16 gal (US)
2.6 gal (US)
-
Diesel Exhaust Fluid Tank
8.7 gal (US)
-
-
Transmission
16 gal (US)
0.8 gal (US)
-
Differential - Final Drives - Front
49 gal (US)
-
-
Differential - Final Drives - Rear
49 gal (US)
-
-
Hydraulic System - Implement/Steering
126 gal (US)
-
-
Note
Cat U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) and are compatible* with ULSD blended with the following lower-carbon intensity fuels** up to: • 20%
DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
-
Cooling System
-
5.7 gal (US)
-
Diesel Exhaust Fluid (DEF) Tank
-
4.8 gal (US)
-
Hydraulic System - Including Tank
-
25.9 gal (US)
-
Hydraulic Tank
-
14.5 gal (US)
-
Axles - Front Center Differential
-
2 gal (US)
-
Axles - Rear Center Differential
-
2 gal (US)
-
Dimensions (Approximate) - Standard Lift
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
14 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
39.3 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Axles
3.2 ft
-
-
Clearance at Maximum Lift
11.9 ft
-
-
B-Pin Height - Maximum Lift
18 ft
-
-
Maximum Overall Height - Bucket Raised
24.5 ft
-
-
Reach - Maximum Lift
6.5 ft
-
-
Note
Specifications are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
-
-
Dimensions (Approximate) - High Lift
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
14.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Bucket Tip
15.3 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
40.7 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Axles
3.2 ft
-
-
Clearance at Maximum Lift
13.3 ft
-
-
B-Pin Height - Maximum Lift
19.3 ft
-
-
Maximum Overall Height - Bucket Raised
25.8 ft
-
-
Reach - Maximum Lift
6.8 ft
-
-
Note
Specifications are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height.
-
-
Dimensions - Millyard Linkage
Ground to Top of ROPS
13.8 ft
-
-
Ground to Top of Exhaust Stacks
13.8 ft
-
-
Ground to Top of Hood
10.9 ft
-
-
Ground to Bumper Clearance
3.1 ft
-
-
Rear Axle - Centerline to Bumper
10.5 ft
-
-
Front Axle Centerline to Fork Tip
16.5 ft
-
-
Wheel Base
14.9 ft
-
-
Maximum Overall Length
41.9 ft
-
-
Ground to Lower Hitch Clearance
1.9 ft
-
-
Ground to Center of Front Axle
3.2 ft
-
-
Fork Height with Level Arms
8.1 ft
-
-
Fork Top Clamp Opening
13.1 ft
-
-
Fork Height at Maximum Lift
17.2 ft
-
-
Hinge Pin Height at Maximum Lift
16.1 ft
-
-
Dump Angle at Maximum Lift
-39.4 °
-
-
Weights
Operating Weight
-
18102 lb
-
Buckets
Bucket Capacities
-
1.3-3.5 m3 (1.7-4.6 yd3)
-
Bucket Capacities - General Purpose
-
1.3-1.9 m³ (1.7-2.5 yd³)
-
Bucket Capacities - Light Material
-
2.5-3.5 m³ (3.3-4.6 yd³)
-
Sustainability
Recyclability
-
95%
-
Cab
ROPS
-
ISO 3471:2008
-
FOPS
-
ISO 3449:2005
-
Note (2)
-
The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A).
-
Note (3)
-
The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A).
-
Note (1)
-
Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
-
Note (4)
-
*The measurements were conducted with the cab doors and windows closed.
-
Steering
Maximum Working Pressure - Steering Pump
-
2683 psi
-
Steering Articulation Angle - Each Direction
-
40 °
-
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed
-
3.2 s
-
Maximum Flow - Steering Pump
-
17 gpm
-
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
-
3.75 turns
-
Loader Hydraulic System
Hydraulic Cycle Time - Dump, at Maximum Reach
-
1.4 s
-
Hydraulic Cycle Time - Total Cycle Time
-
12.5 s
-
Maximum Working Pressure - Implement Pump
-
3408 psi
-
Relief Pressure - Tilt Cylinder
-
4931 psi
-
Hydraulic Cycle Time - Rackback
-
2.2 s
-
Relief Pressure - Tilt Cylinder - 3rd Function Maximum Working Pressure
-
3046 psi
-
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift
-
5.2 s
-
Relief Pressure - Tilt Cylinder - 4th Function Maximum Working Pressure
-
3046 psi
-
Maximum Flow - Implement Pump - 4th Function, Maximum Flow
-
24 gpm
-
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow
-
24 gpm
-
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level
-
3.7 s
-
Maximum Flow - Implement Pump
-
32 gpm
-
Tires
Note (2)
-
In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
