Engine meets Tier 4 Final/Stage V emission standards.
-
-
Note
Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
-
-
Maximum Gross Power - ISO 14396
110 HP
-
-
Net Power @ 1,700 rpm – ISO 9249:2007, SAE J1349:2011
-
393 HP
-
Note (1)
-
Cat engine meets U.S. EPA Tier 4 Final, EU Stage V, Korea Stage V, China Nonroad Stage IV and Japan 2014 emission standards.
-
Note (2)
-
The net power advertised is the power available at the flywheel when the engine is equipped with fan, alternator, air cleaner, and aftertreatment.
-
Gross Torque @ 1,200 rpm – SAE J1995:2014
-
1627 lb/ft
-
Engine Torque @ 1,200 rpm – ISO 14396:2002
-
1612 lb/ft
-
Gross Power @ 1,700 rpm – SAE J1995:2014
-
425 HP
-
Net Torque @ 1,100 rpm – ISO 9249:2007, SAE J1349:2011
-
1539 lb/ft
-
Engine Power @ 1,700 rpm – ISO 14396:2002
-
429 HP
-
Note (3)
-
Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: • 20% biodiesel FAME (fatty acid methyl ester)* • 100% renewable diesel, HVO (h
-
Weights
Operating Weight
18102 lb
66877 lb
-
Note
-
Weight based on a machine configuration with Bridgestone 29.5R25 VSNT L4 radial tires, full fluids, operator, standard counterweight, ride control cold start, roading fenders, Product Link, open differential axles (front/rear), secondary steering, sound s
-
Buckets
Bucket Capacities
1.3-3.5 m3 (1.7-4.6 yd3)
-
-
Bucket Capacities - General Purpose
1.3-1.9 m³ (1.7-2.5 yd³)
-
-
Bucket Capacities - Light Material
2.5-3.5 m³ (3.3-4.6 yd³)
-
-
Sustainability
Recyclability
95%
-
-
Cab
ROPS
ISO 3471:2008
-
-
FOPS
ISO 3449:2005
-
-
Note (2)
The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A).
-
-
Note (3)
The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A).
-
-
Note (1)
Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
-
-
Note (4)
*The measurements were conducted with the cab doors and windows closed.
-
-
Service Refill Capacities
Cooling System
5.7 gal (US)
13.7 gal (US)
-
Fuel Tank
43.6 gal (US)
112.5 gal (US)
-
Hydraulic System - Including Tank
25.9 gal (US)
-
-
Engine Crankcase
2.6 gal (US)
-
-
Hydraulic Tank
14.5 gal (US)
40.4 gal (US)
-
Transmission
0.8 gal (US)
20.3 gal (US)
-
Note
DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
-
-
Axles - Front Center Differential
2 gal (US)
-
-
Axles - Rear Center Differential
2 gal (US)
-
-
Diesel Exhaust Fluid (DEF) Tank
4.8 gal (US)
-
-
Crankcase
-
9.8 gal (US)
-
DEF Tank
-
5.5 gal (US)
-
Differential - Final Drives - Front
-
22.2 gal (US)
-
Differential - Final Drives - Rear
-
22.4 gal (US)
-
Steering
Maximum Working Pressure - Steering Pump
2683 psi
-
-
Steering Articulation Angle - Each Direction
40 °
-
-
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed
3.2 s
-
-
Maximum Flow - Steering Pump
17 gal/min
-
-
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left
3.75 turns
-
-
Loader Hydraulic System
Hydraulic Cycle Time - Dump, at Maximum Reach
1.4 s
-
-
Hydraulic Cycle Time - Total Cycle Time
12.5 s
-
-
Maximum Working Pressure - Implement Pump
3408 psi
-
-
Relief Pressure - Tilt Cylinder
4931 psi
-
-
Hydraulic Cycle Time - Rackback
2.2 s
-
-
Relief Pressure - Tilt Cylinder - 3rd Function Maximum Working Pressure
3046 psi
-
-
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift
5.2 s
-
-
Relief Pressure - Tilt Cylinder - 4th Function Maximum Working Pressure
3046 psi
-
-
Maximum Flow - Implement Pump - 4th Function, Maximum Flow
24 gal/min
-
-
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow
24 gal/min
-
-
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level
3.7 s
-
-
Maximum Flow - Implement Pump
32 gal/min
-
-
Transmission
Note
*Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
Maximum travel speed in standard vehicle with empty bucket and standard L4 tires with 935 mm (37 in) roll radius.
-
Forward and Reverse - Speed Range 3
25 mile/h
-
-
Forward and Reverse - Speed Range 2*
12.5 mile/h
-
-
Forward and Reverse - Speed Range 1*
6.3 mile/h
-
-
Forward - 1
-
4.3 mile/h
-
Forward - 2
-
8.3 mile/h
-
Forward - 3
-
14.6 mile/h
-
Forward - 4
-
24.5 mile/h
-
Reverse - 1
-
4.8 mile/h
-
Reverse - 2
-
9.4 mile/h
-
Reverse - 3
-
16.7 mile/h
-
Reverse - 4
-
24.5 mile/h
-
Tires
Note (2)
In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
** For machines in European Union countries and in countries that adopt the �EU Directives.�
-
Note (2)
-
***European Union Directive �2000/14/EC� as amended by �2005/88/EC.�
-
With Cooling Fan Speed at 70% of Maximum Value - Exterior Sound Power Level*
-
109
-
With Cooling Fan Speed at 70% of Maximum Value - Operator Sound Pressure Level (ISO 6396:2008)
-
72 dB(A)
-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Power Level (ISO 6395:2008)
-
112 dB(A)
-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Pressure Level (SAE J88:2013)
-
78
-
With Cooling Fan Speed at Maximum Speed - Operator Sound Pressure Level (ISO 6396:2008)
-
72 dB(A)
-
Air Conditioning System
Air Conditioning
-
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.9 kg (4.2 lb) of refrigerant which has a CO2 equivalent 2.717 metric tonnes (2.995 tons).
-
Operating Specifications
Breakout Force
-
51008 lb
-
Note (1)
-
For a machine configuration as defined under �Weight.�
-
Note (2)
-
Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing.
-
Static Tipping Load - Full 40° Turn - No Tire Deflection
-
20965 kg
-
Static Tipping Load - Full 40° Turn - With Tire Deflection
-
43432 lb
-
Hydraulic System
Implement System - Maximum Operating Pressure
-
4975 psi
-
Implement System - Maximum Pump Output at 2,250 rpm
-
119 gal/min
-
Dimensions
Note
-
All dimensions are approximate and based on machine equipped with 5.4 m3 (7.1 yd3) general purpose bucket with BOCE and Bridgestone 29.5R25 VSNT L4 radial tires.
