Compare Equipment Go Back
 MD6200 Rotary Blasthole Drill Specifications |
 MD6310 Rotary Blasthole Drill 13.7 m or 17.5 m (44.9 ft or 57.4 ft) Mast Configuration |
 MD6250 Rotary Blasthole Drill Specifications |
|
Pull-Down/Hoisting Capacity |
|||
|---|---|---|---|
| Pull-Down Capacity | Up to 15 876 kg (Up to 35,000 lb) | Up to 39 009 kg (86,000 lb) | Up to 20 411 kg (45,000 lb) |
Specifications |
|||
| Hole Diameter | 140-200 mm (5.5-7.87 in) | 229-311 mm (9-12.25 in) | 165-250 mm (6.5-9.88 in) |
| Engine | Cat© C18 | Cat® C32B | Cat® C27 |
| Bit Load | Up to 16 964 kg (37,400 lb) | Up to 42 149 kg (Up to 92,922 lb) | Up to 32 655 kg (Up to 71,993 lb) |
Basic Specs |
|||
| U.S. EPA Tier 2 Equivalent - Engine | C18 @ 1,800 rpm | - | - |
| U.S. EPA Tier 2 Equivalent - Emissions | U.S. EPA Tier 2 equivalent | - | - |
| U.S. EPA Tier 4 Final - Engine | C18 @ 1,800 rpm | - | - |
| U.S. EPA Tier 4 Final - Emissions | U.S. EPA Tier 4 Final | - | - |
| Compressor - Rotary Drilling | 32.6 cmm (1,150 cfm) @ 8.6 bar (125 psi) | - | - |
| Angle Drilling Available | 30 degrees to 0 degrees in 5-degree increments | - | - |
| Bit Load (single-Pass) | 37400 lb | - | - |
| Hoist Speed | 4.3 ft/s | - | - |
| Hole Diameter Range | 140-200 mm (5.5-7.87 in) | - | - |
| Hole Depth Range - Single-Pass Depth | 36 ft | - | - |
| Compressor - DTH Drilling | 29.7 m_/min (1,050 ft_/min) @ 24.1 bar (350 psi) | 42.2 m³/min (1,500 ft³/min) @ 34.4 bar (500 psi) | - |
| Pull-DownCapacity | Up to 15 876 kg (Up to 35,000 lb) | - | - |
| Hoist Capacity | Up to 11 907 kg (Up to 26,250 lb) | - | - |
| Hole Depth Range - Multi-Pass Depth | Down to 47.58 m (Down to 156 ft) | - | - |
| U.S. EPA Tier 4 Final - Power Rating (ISO 14396) | 589 HP | - | - |
| U.S. EPA Tier 2 Equivalent - Power Rating (ISO 14396) | 587 HP | - | - |
| 13.7 m (44.9 ft) Mast - Hoist Speed | - | 122.7 ft/min | - |
| 17.5 m (57.4 ft) Mast - Hoist Speed | - | 122.7 ft/min | - |
| Emissions (Equivalent to Tier 2): Engine | - | C32B @ 1,800 rpm | - |
| 13.7 m (44.9 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Multi Pass Depth | - | Down to 74.6 m (Down to 244.9 ft) | - |
| 17.5 m (57.4 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Multi Pass Depth | - | Down to 47.9 m (Down to 157.4 ft) | - |
| 17.5 m (57.4 ft) Mast - Pulldown Capacity | - | Up to 39 009 kg (Up to 86,000 lb) | - |
| 17.5 m (57.4 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Single Pass Depth | - | 57.4 ft | - |
| 13.7 m (44.9 ft) Mast - Hole Diameter Range | - | 203-311 mm (8-12.25 in) | - |
| Angle Drilling | - | Vertical to 30° (in 5° increments) | - |
| 17.5 m (57.4 ft) Mast - Hole Diameter Range | - | 203-311 mm (8-12.25 in) | - |
| 17.5 m (57.4 ft) Mast - Bit Load - Single Pass | - | Up to 42 149 kg (Up to 92,922 lb) | - |
| 13.7 m (44.9 ft) Mast - Hoist Capacity | - | Up to 22 113 kg (Up to 48,750 lb) | - |
| Compressor - Rotary Drilling (1) | - | 56.6 m³/min (2,000 ft³/min) @ 8.6 bar (125 psi) | - |
| Compressor - Rotary Drilling (2) | - | 73.6 m³/min (2,600 ft³/min) @ 7.6 bar (110 psi) | - |
| 13.7 m (44.9 ft) Mast - Pulldown Capacity | - | Up to 39 009 kg (Up to 86,000 lb) | - |
| 13.7 m (44.9 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Single Pass Depth | - | 44.9 ft | - |
| Emissions (U.S. EPA Tier 4 Final): Engine | - | C32B @ 1,800 rpm | - |
| 17.5 m (57.4 ft) Mast - Hoist Capacity | - | Up to 22 113 kg (Up to 48,750 lb) | - |
| 13.7 m (44.9 ft) Mast - Bit Load - Single Pass | - | Up to 41 165 kg (Up to 90,753 lb) | - |
| Emissions (U.S. EPA Tier 4 Final): Power Rating ISO 14396 | - | 1007 HP | - |
| Emissions (Equivalent to Tier 2): Power Rating ISO 14396 | - | 1031 HP | - |
Compressor Choices |
|||
| DTH Drilling | Includes tool lubrication system | - | - |
| Rotary Drilling | Optional tool lubrication system | - | - |
| Note | With the compressor's electronic controls plus variable volume control, the operator can adjust air output to reach optimal match of tool, flushing air and ground conditions. Both high and low pressure compressors contain this feature. | - | - |
| DTH Drilling - 1050 cfm/350 psi | 29.7 cmm (1,050 cfm) @ 24.1 bar (350 psi) with 113.5 L (30 gal) tool oiler | - | - |
| Rotary Drilling - 1150 cfm/125 psi | 32.6 cmm (1,150 cfm) @ 8.6 bar (125 psi) | - | - |
Receiver Tank Choices |
|||
| Choice (1) | Low pressure 8.6 bar (125 psi) | - | - |
| Choice (2) | High pressure 24.1 bar (350 psi) | - | - |
Cooling |
|||
| Components (1) | Coolers with easy cleaning access | Coolers with easy cleaning access | Coolers with easy cleaning access |
| Components (2) | All cooler core sections are replaceable | Separate engine cooling module | Separate engine cooling module |
| Components (3) | Functional in ambient temperature of up to 52� C (125� F) | Replaceable cooler core sections | All cooler core sections are replaceable |
| Components (4) | Automatic variable speed fan control | Automatic variable speed fan control | Automatic variable speed fan control |
| Features | - | Functional in ambient temperature of 52° C (125° F) | Functional in ambient temperature of 52° C (125° F) |
Climate Choices |
|||
| Climate Level 1 Standard Fluids and Lubricants (1) | Rated down to -1C (30 F) | Rated down to –1° C (30° F) temperatures | Rated down to –1° C (30° F) |
| Climate Level 1 Standard Fluids and Lubricants (2) | Withstands high heat up to 52 C (125 F) | Withstands high heat to 52° C (125° F) | Withstands high heat to 52° C (125° F) |
| Climate Level 2 Arctic Fluids and Lubricants, Engine Block and Manifold Heater 120V or 240V | Rated down to -18 C (0 F) | - | - |
| Climate Level 2 Arctic Fluids and Lubricants | - | Rated down to –18° C (–0.4° F) temperatures | Rated down to –18° C (–0.4° F) |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (6) | - | Breaker panel includes five (5) additional breakers for locally supplied heating elements, if needed | - |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (3) | - | Full arctic lubricant package includes: engine oil, compressor oil and hydraulic oil | - |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (1) | - | Rated down to –40° C (–40° F) temperatures | - |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (5) | - | Shore power connection box with switchable 240-600V (50 amp) connection; diesel genset and or plug, sold separately | - |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (2) | - | Diesel fired heating system that heats and circulates engine coolant through the: engine block, primary water tank, heating elements for battery trays with a provision for fuel tanks | - |
| Climate Level 4 Arctic Fluids and Lubricants, Heating Package (4) | - | Electric heating package with breaker panel to power: 120V heating blanket for compressor receiver tank, compressor control box, heat trace for compressor control lines, heat trace for housing from water tank to water pump and water fast-fill assembly plu | - |
| Climate Level 4 Arctic Fluids and Lubricants (1) | - | - | Rated down to –40° C (–40° F) |
| Climate Level 4 Arctic Fluids and Lubricants (2) | - | - | Diesel fired heating system that heats and circulates engine coolant through engine block, below deck water tank, heating elements for battery trays |
| Climate Level 4 Arctic Fluids and Lubricants (3) | - | - | Full Arctic lubricant package to include engine and hydraulic oil |
| Climate Level 4 Arctic Fluids and Lubricants (4) | - | - | Electric heating package with breaker panel to power: 120V heating blanket for compressor receiver tank, heat trace for hosing from water tank to water pump and water fast-fill assembly, plus primary tank |
| Climate Level 4 Arctic Fluids and Lubricants (5) | - | - | Shore power connection box with switchable 240-600V (50 amp) connection (diesel gen set and/or plug supplied locally). Box includes standard 50 hz battery charger, if 60 hz charger required, to be ordered via after market, refer to P-n 540-4271 |
| Climate Level 4 Arctic fluids and lubricants (6) | - | - | Breaker panel includes five (5) additional breakers for locally supplied heating elements if needed |
| Batteries, Sealed (1) | - | - | Quantity: Four (4) |
| Batteries, Sealed (2) | - | - | Quantity: Six (6) (required for cold weather Level 2 and 4 and/or semi autonomy packages) |
Frame and Work Deck |
|||
| Features (1) | Jacks, mast pivot and deck are welded integrally to mainframe for maximum durability and long life | Jacks, mast pivot and deck are welded integrally to mainframe for maximum durability and long life | Leveling Jacks, A-frame/mast pivot and drill deck are welded integrally to mainframe for maximum durability and long life |
| Features (2) | Slip resistant surfaces | Slip resistant surface | Primary fuel tank capacity 1416 L (374 gal) |
| Features (3) | Fuel tank capacity 833 L (220 gal) | Fuel tank capacity 1609 L (425 gal) | Fuel capacity expansion for additional 1416 L (374 gal) optional for total capacity of 2832 L (748 gal); (required for autonomy packages) |
| Components (1) | Three leveling jacks provide leveling on a 7� bench (any orientation) | Stationary rear deck; for vertical and angle drilling | Stationary drill deck; for vertical and angle drilling |
| Components (2) | Heavy duty tow hooks (non-drill end) | Four leveling jacks to provide leveling on a 7° bench (any orientation) | Four leveling jacks provide leveling on a 7° bench (any orientation) |
| Components (3) | Four (4) lift lugs, for use with cables or chains | Manual, centralized, lubrication banks for all pivot points on drill, or automated lubrication system (option) | Heavy duty tow hooks (front end) |
| Components (5) | - | Four (4) lift lugs, for use with cables or chains | Fixed access stairs to the cab area |
| Components (7) | - | Bit storage box in-deck with hinged cover (option) | - |
| Components (6) | - | Walkway around cab to drill deck (option) | Sturdy guardrails with toe guards, self-closing gates |
| Features (6) | - | Three egress points on deck areas in addition to main access | - |
| Components (10) | - | Drill pipe thread greaser with remote fill tank or disposable grease bucket (option) | - |
| Features (7) | - | Sturdy guardrails, toe guards, self closing gates | - |
| Components (4) | - | Heavy duty tow hooks (front end) | Four (4) lift lugs, for use with cables or chains |
| Components (8) | - | DTH hammer storage on drill deck with high pressure configuration (option) | - |
| Features (4) | - | Fuel capacity expansion for additional +1609 L (425 gal) | Three (3) egress points on deck areas in addition to main access |
| Features (5) | - | Bolt-on platform for cold weather generator or fire suppression bottles (option) | - |
| Components (9) | - | Hydraulically operated viewing hatch in drill deck with spotlight (option) | - |
Frame Access Choices |
|||
| Choice (1) | Fixed access steps to the cab area | Fixed access ladder to the cab area | - |
| Choice (2) | Small platform to the cab includes fixed access steps | Cascading, hydraulic stairs to cab area (option) – includes jack and tram interlock that activates when the stairs are down | - |
| Choice (3) | Platform access to the cab with full length service access walkway includes fixed access steps and self-closing gates | Cab perimeter walkway available with either choice | - |
Drill Deck Misc. |
|||
| Components (1) | Drill pipe thread greaser with remote fill tank that also accommodates disposable grease bucket | - | - |
Undercarriage |
|||
| Model | Cat® 336 Excavator type | Cat® 349E EL Excavator type | Cat® 336E EL Excavator type |
| Carrier Rollers | Three (3) | Three (3) | Three (3) |
| Triple Grousers (1) | 600 mm (23.6 in); 0.89 bar (12.6 psi) ground pressure | - | 600 mm (23.6 in); for hard rock; 0.88 bar (12.7 psi) ground bearing pressure |
| Drawbar Pull | 262 000 Nm (193,241 lbf-ft) | 122971 lbf | 93745 lbf |
| Components (1) | Track chain guards and guides | - | - |
| Lower rollers | Eight (8) | Fourteen (14) | Twelve (12) |
| Travel Speed - High | 2 mile/h | - | - |
| Travel Speed - Low | 1.3 mile/h | - | - |
| Track chain guards and guides | - | Level two | Level two |
| Travel Speed | - | 1.5 mile/h | 1.5 mile/h |
| Triple grousers for soft rock ground bearing pressure 1.28 bar (18.5 psi) | - | 29.5 in | - |
| Triple Grousers (2) | - | - | 750 mm (29.5 in); for soft rock; 1.10 bar (15.9 psi) ground bearing pressure |
Hydraulics |
|||
| Components (1) | Two (2) main pumps: 85 cc (piston with proportional electronic controls) | Two (2) primary pumps – 210 cc (piston, with proportional electronic controls) | Two (2) primary pumps – 145 cc (piston, with proportional electronic controls) |
| Components (2) | One (1) auxiliary circuit pump: 45 cc (piston, load sensing) | One (1) auxiliary circuit pump – 110 cc (piston, load sensing) | One (1) auxiliary circuit pump – 110 cc (piston, load sensing) |
| Components (3) | One (1) fan pump: 45 cc (piston with proportional electronic controls) | Two (2) fan pumps – 1,000 cc (piston, with proportional electronic controls) | Two (2) fan pumps – 74 cc (piston, with proportional electronic controls) |
| Components (4) | One (1) charge pump: 73.8 cc (gear, fixed displacement) | Two (2) charge pumps – 43.9 + 56.5 cc (double stack gear, fixed displacement) | Two (2) charge pumps – 43.9 + 56.5 cc (double stack gear, fixed displacement) |
| Components (5) | Scheduled Oil Sampling (S-O-S SM) ports | Scheduled Oil Sampling (S∙O∙S) ports | Scheduled Oil Sampling (S·O·S) ports |
Tool Package Rotary |
|||
| Components (7) | Drill tool lubricator (optional) | - | - |
| Components (1) | One-piece roller deck bushing | Roller deck bushing | One-piece roller deck bushing |
| Components (2) | Pipe positioner clamps | Pipe positioner inserts | Pipe positioner rollers |
| Components (3) | Deck wrench | Deck wrench, sliding | Deck wrench |
| Components (4) | Bit sub | Top Sub, or Shock sub and cross over adapter (option) | Top sub |
| Components (5) | Top sub | Bit sub | Bit sub |
| Components (6) | Pipe wiper seal | Pipe wiper seal | Pipe wiper seal |
Dust Control Choices |
|||
| High Volume Water Injection - Maximum - Tank Above Deck - Capacity | 200 gal (US) | - | - |
| Water Injection - Tank Mounted Below Front Deck - Components | Water flow meter, volume control, tank fill level indicator | - | - |
| High Volume Water Injection - Maximum - Tank Below Deck - Capacity | 200 gal (US) | - | - |
| Water Injection - Tank Mounted Below Front Deck | 200 gal (US) | - | - |
| High Volume Water Injection - Maximum - Tanks Total Capacity | 400 gal (US) | - | - |
| Water Injection plus Dust Collector (1) | 76.5 cmm (2,700 cfm) dust collector; includes standard water injection | - | - |
| Water Injection plus Dust Collector (2) | Self-cleaning filters, dust chute clean-out door | - | - |
| Choices (1) | Static dust curtains, four sides boxed enclosed | - | Water injection – tank mounted below front deck 1271 L (336 gal) – Water flow meter, volume control, tank fill level indicator |
| Choices (2) | Dust curtain hydraulic lifters raise front and rear dust curtains (option) (recommended with dry dust collector) | - | Water injection plus dry dust collector 127 m³/min (4,500 ft³/min) dust collector; includes standard water injection – Self-cleaning filters, dust chute with ejector |
| Choices (3) | Tram off spray system (option) | - | High volume water injection (maximum) – tanks total capacity 2786 L (736 gal) – Tank below deck (isolated for extreme cold weather) capacity 1271 L (336 gal) – Tank above deck capacity 1514 L (400 gal) |
| Choices (4) | - | - | Static dust curtains, four sided/boxed enclosed |
Mast Packages |
|||
| Single-Pass Depth | 36 ft | - | - |
| Multi-Pass Depth | Down to 47.58 m (Down to 156 ft) | - | - |
| Pulldown - Rated Single Cylinder Pull-Down/Hoist System | Up to 15 876 kg (Up to 35,000 lb) | - | - |
| Hoist | Up to 11 907 kg (Up to 26,250 lb) | - | - |
| Mast Accessories Hydraulic (2) | - | One hydraulic pipe catcher, plus one wire rope, hydraulically actuated pipe positioner, hydraulic bit basket | - |
| Mast Accessories Hydraulic (1) | - | One hydraulic pipe catcher, hydraulically actuated pipe positioner, hydraulic bit basket | - |
| Angle Drilling | - | Included with either mast | Included with either mast |
| Mast Accessories Manual, 17.5 m (57.4 ft) Mast | - | Two wire rope pipe catchers, hydraulically actuated pipe positioner, manual bit basket | - |
| Mast Accessories Manual, 13.7 m (44.9 ft) Mast | - | One wire rope pipe catcher, hydraulically actuated pipe positioner, manual bit basket | - |
| Mast Accessories Manual - 11.2 m (36.7 ft) or 13.6 m (44.6 ft) Mast | - | - | One (1) wire rope pipe catcher, manual bit basket |
| Mast Accessories Hydraulic - 11.2 m (36.7 ft) Mast | - | - | One (1) hydraulically actuated pipe catcher, hydraulically operated bit basket |
| Mast Accessories Hydraulic - 13.6 m (44.6 ft) Mast | - | - | One (1) hydraulically actuated pipe catcher, plus one (1) wire rope pipe catcher, hydraulically operated bit basket |
Engine Features |
|||
| Feature (3) | Tier 4 Final package complete with DEF/Engine Shutdown Control Package | - | - |
| Feature (1) | Dual starter motors | - | - |
| Feature (2) | Ether starting aid | - | - |
Tool Package DTH |
|||
| Components (8) | Top sub | - | Drill tool lubricator is included with selection of DTH Compressor |
| Components (7) | Drill tool lubricator is included with selection of DTH Compressor | - | Pipe wiper seal |
| Components (1) | Two-piece bushing | Two piece bushing | Two-piece roller deck bushing |
| Components (2) | Pipe positioner clamps | Pipe positioner inserts | Pipe positioner rollers |
| Components (3) | Deck wrench | Deck wrench, sliding | Deck wrench |
| Components (4) | Shock sub | Shock sub and top sub adapter | Shock sub |
| Components (5) | Cross over subs | Cross over hammer adapter | Top Sub |
| Components (6) | Pipe wiper seal | Pipe wiper seal | Hammer Sub |
Dimensions (Approximate) |
|||
| Width cab end* | 13.7 ft | - | - |
| Width non-cab end | 11.7 ft | - | - |
| Height mast up | 54.3 ft | - | - |
| Body Length | 31 ft | - | - |
| Length mast down | 57.5 ft | - | - |
| Height mast down | 11.75 ft | - | - |
| Mast only length | 52.1 ft | - | - |
| Note | *Contact the factory for width with platform access to cab or service platform walkway. | - | - |
Drill Pipe |
|||
| 9.14 m (30 ft) pipes - Accepts quantity of four (4) - Option 5 | 6 in | - | - |
| 9.14 m (30 ft) pipes - Accepts quantity of four (4) - Option 4 | 5.5 in | - | - |
| 7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary (1) | - | 8 in | - |
| 7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: DTH | - | 7 in | - |
| 7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary or DTH | - | 7.625 in | - |
| 7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary (2) | - | 8.625 in | - |
| 7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary | - | 9.25 in | - |
| 12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary (2) | - | 8.625 in | - |
| 12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary (1) | - | 8 in | - |
| 12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: DTH | - | 7 in | - |
| 12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary or DTH | - | 7.625 in | - |
| Note | - | Dual purpose carousel pipe: 13.7 m (44.9 ft) Mast; holds quantity of two (2) 12.19 m (40 ft) pipes and quantity of two (2) 9.14 m (30 ft) pipes, and adapters to connect to DTH hammer and tricone bit (DTH hammer and tricone not included)
|
- |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 4 | - | - | 6.5 in |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 1 | - | - | 5 in |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 6 | - | - | 7.625 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 1 | - | - | 5 in |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 3 | - | - | 6 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 6 | - | - | 7.625 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 4 | - | - | 6.5 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 3 | - | - | 6 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 2 | - | - | 5.5 in |
| 10.6 m (35 ft) Pipes for 11.2 m (36.7 ft) Mast - holds quantity of four (4) - Option 5 | - | - | 7 in |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 2 | - | - | 5.5 in |
| 6.1 m (20 ft) Pipes for 13.6 m (44.6 ft) Mast - holds quantity of four (4) - Option 5 | - | - | 7 in |
Mast and Pipe Carousel Features |
|||
| Features (1) | Pipe carousel: Accepts quantity of four (4) 9.14 m (30 ft) pipes |
- | - |
| Features (2) | Standard angle drilling package (0 to 30 degrees, in�5-degree�increments) | - | - |
| Features (4) | Hydraulically actuated, self-indexing pipe carousel accepts pipe diameters up to 152 mm (6.0 in) | - | - |
| Features (5) | Drills strings configured for bit changes above deck | - | - |
| Features (6) | Single cylinder pulldown/hoist system | - | - |
| Features (7) | Sliding deck wrench assembly | - | - |
| Features (8) | Configured with roller deck bushing (for low pressure/tricone drilling) | - | - |
| Features (9) | Two-piece deck bushing (for high pressure DTH drilling) | - | - |
| Features (10) | Overhead winch with cable and hook plus remote control; variable speed drive with a 1361 kg (3,000 lb) rating | - | - |
| Features (11) | Variable grip hydraulic break out wrench grip range 101-152 mm (4.0-6.0 in) | - | - |
| Features (12) | Closed circuit camera mounted in mast to view pipe carousel/top drive operation | - | - |
| Features (13) | Pipe positioner for angle drilling, multi-pass pipe handling | - | - |
| Features (14) | Manual pipe catcher: One (1) wire rope, pipe catcher, pipe positioner, optional manual bit basket | - | - |
Rotary Head Top Drive System |
|||
| Torque - Single Motor | 6166 lb/ft | - | 8629 lb/ft |
| Rotation Speed | 0-150 rpm | - | 0-160 rpm |
| Components (1) | Rotary torque control | Spindle with 168 mm (6.625 in) API regular thread and splined collar | Spindle – 140 mm (5.5 in) API regular thread with splined collar |
| Components (2) | Virtual rotary head travel interlocks | Rotation gear box with dual motor arrangement, up to 160 rpm, and 16 000 N∙m (11,800 lbf-ft) of torque | Rotary torque control |
| Components (3) | Virtual rotary head travel interlocks | Rotary torque control | Virtual rotary head travel interlocks |
| Components (4) | - | Virtual rotary head travel stops and interlocks | - |
Operator Environment |
|||
| Cab Design | Falling Object Protective Structure (FOPS) certified cab includes: - Rubber shock-mounts to absorb mechanical vibration - Operator station design that integrates an ergonomic seat, joystick controls with full instrumentation, dual 254 mm (10 in) hig |
- | – Spacious FOPS cab is 3 m² (32.3 ft²) with an integrated operator station – Cab rubber shock-mounts – Operator station design integrates an ergonomic seat, joystick controls with full instrumentation, and dual 254 mm (10 in) color displays, high de |
| Cab Packages | Standard configuration includes a fabric seat, removable floor mat, single pane window glass and driller window guard Premium configuration includes a leather seat with heat and ventilation, heavy duty suspension, dual pane window glass a |
- | - |
| Seating | - Swivel seat is fully ergonomic, with tilt (5° adjustment), lumbar support, and fore/aft seat adjustment 80 mm (3.1 in) - Seat locks and has two point retractable, 76 mm (3 in) seat belt |
- | – Seat swivels, locks and retractable, two-point/76 mm (3 in) wide seat belt, tilts (5° adjustment), lumbar support, fore/aft seat adjustment 80 mm (3.1 in) |
| Windows | - Large windows on the front, rear and right cab side; full length drill window with guard - Window shades (option) - Windshield wiper with a common washer tank - Manometer Pressure Gauge (option) |
- | – Large windows front, rear and right cab side; full length drill window with guard – Windshield wipers with a common washer tank |
| Lighting | - LED interior lights, backlit joysticks and keypads - Flood lights for the drill perimeter; area spotlights - Mast beacon and tram flashing strobe light (option) |
– LED interior lights; separate reading light, and backlit joysticks and keypads – Zone controls for area lights and spot lighting for night drilling – Flood lights for the drill perimeter – Spot lights for power group area; drill deck; mast caro |
– LED interior lights and map light at operators seat, backlit joysticks and keypads – Flood lights for the drill perimeter – Spotlights for power group area; drill deck; mast carousel; access ladder and walkways – Lighting package includes 4,200 |
| HVAC | - Floor heating vent - Filter access from deck, 500 hour service interval - Defogging HVAC vents on main window |
– Floor vents in the foot rest area – Roof-mounted air conditioner/heating/pressurizing unit – Filter access from deck, does not require roof access, and has approximately 500 hour service interval – Defogging HVAC vents on driller window |
– Floor heating vent – Roof-mounted air conditioner/heating/pressurizing unit – Filter access from deck – Defogging HVAC vents on main window |
| Cameras | - Three (3) CC cameras (front, right and left sides) provide 360° visibility from operators seat; camera on the mast to view pipe carousel/top drive operation | – Mounted on the front and left sides to provide 360° view from operator's seat – Camera on the mast to view pipe carousel/top drive operation |
- |
| Components (7) | - | Operator station design integrates an ergonomic seat, armchair joystick controls with full instrumentation, and two 254 mm (10 in) color, high definition touchscreens and 12 volt power port | - |
| Components (4) | - | Drill performance touchscreen display | - |
| Components (3) | - | Cab perimeter walkway available for both cab sizes | - |
| Components (1) | - | Spacious FOPS cab has 3 m² (32.4 ft²) floor space with an integrated operator station | - |
| Components (13) | - | Seat swivels, locks and has two point/76 mm (3 in) seat belt, tilts (5° adjustment), lumbar support, fore/aft seat adjustment 80 mm (3.1 in) | - |
| Components (9) | - | Power convertor 24V to 12V | - |
| Components (2) | - | Extended cab option 4.2 m² (45.2 ft²); prewired and dedicated space for refrigerator and microwave | - |
| Components (6) | - | Two swing-out hinged doors with windows and Cat keyed locks | - |
| Components (14) | - | Trainer’s seat that folds away and has retractable seat belt (optional) | - |
| Components (5) | - | Cab rubber shock-mounts absorb mechanical vibration and restrict exterior noise | - |
| Components (10) | - | Radio-ready for communication and entertainment radio | - |
| Cab - Premium | - | – Leather seat with heat and ventilation – Dual pane window glass – Front window guard – Additional in-cab storage box – Additional windshield wipers on front and rear windows – Window shades (option) – Foldaway trainer’s seat (option) | – Additional storage – Leather seat with heat and ventilation – Heavy duty seat suspension – Dual pane window glass – Removable guard for driller window, plus window facing power train – Wipers for the driller window plus front and rear win |
| Components (11) | - | Cab roof access ladder (option) | - |
| Cab - Standard | - | – Fabric seat – Single pane window glass – Windshield wiper for driller window – Window shades (option) – Foldaway trainer’s seat (option) – Removable floor mat |
– Fabric seat – Single pane window glass – Removable guard for driller window – Wiper for the driller window |
| Components (8) | - | Additional display screen for cc cameras; color, high-definition 254 mm (10 in) | - |
| Components (12) | - | Literature holder | - |
Operating System Controls - Standard |
|||
| Components (1) | Electric controls for drilling, tramming, leveling plus auxiliary functions | All electric controls for drilling, tramming, leveling plus auxiliary functions | All electric controls for drilling, tramming, leveling plus auxiliary functions |
| Components (2) | Rotary torque control | Electronic compressor control | Electronic compressor control |
| Components (3) | Virtual rotary head travel stops | Rotation torque control | Rotary torque control |
| Components (4) | Pipe positioner engaged/disengaged indicator | Virtual rotary head travel stops and interlocks | Virtual rotary head travel stops and interlocks |
| Components (5) | Drill depth meter | Pipe positioner engaged/disengaged indicator | Pipe positioner engaged/disengaged indicator |
| Components (6) | Drill performance and display system | Drill depth meter | Drill depth meter |
| Components (7) | Delayed engine shut down | Drill performance and display system | Drill performance and drill health display system |
| Components (8) | Filter indicators for hydraulic, fuel, compressor and engine | Delayed engine shut down | Data logging of machine health with warnings and fault code records with export capability |
| Components (9) | Jack pressure sensors | Rotary head rpm gauge – (digital display in screen) | Delayed engine shut down |
| Components (10) | Data logging of machine health with warnings and fault code records with export capability | Filter indicators for hydraulic, compressor and engine | Rotary head rpm gauge (digital display in screen) |
| Components (11) | Dust suppression control | Jack pressure sensors in the display | Filter indicators for hydraulic, fuel, compressor and engine |
| Components (12) | Mast lock indicator | Dust suppression control | Jack pressure sensors in display |
| Components (13) | ECM proportional fan speed control system | Mast lock indicator | Dust suppression control |
| Components (14) | Tram interlock, machine stability limits | ECM controlled proportional fan speed control system | Mast lock indicator |
| Components (15) | Tram interlock, pipe in hole | Tram interlock, machine stability limits | ECM proportional fan speed control system |
| Components (16) | Tram interlock, mast up and locked or down and parked | Tram interlock, pipe in hole | Tram interlock, machine stability limits |
| Components (17) | Tram interlock, jacks retracted | Tram interlock, mast up and locked or down and parked | Tram interlock, pipe in hole |
| Components (18) | Tram interlock, winch parked | Tram interlock, jacks retracted | Tram interlock, mast up and locked or down and parked |
| Components (19) | Cab environment controls (AC, heat, fan speeds) | Cab environment controls (AC, filter, heat, fan speeds) | Tram interlock, jack retracted |
| Components (20) | Pre wired for Terrain and Autonomous Operation | Cabin pressure manometer with indicator (option) | Tram interlock, winch parked |
| Components (23) | - | Data logging of machine health with warnings, and fault code records; export capability | Drill Assist automated functionality: – Auto level, auto jack retract – Auto mast raise and lock, auto mast unlock and park |
| Components (22) | - | Prewired for Terrain and autonomous operation | Prewired for Terrain and autonomous operation |
| Components (21) | - | Dust curtain lifting system – auto hydraulic raise front and rear (option) | Cab environment controls (AC, filter, heat, fan speeds) |
Automation and Technology |
|||
| Type (1) | Autonomous ready | - | Cat Terrain ready |
| Components (1) | Drill depth meter | Drill depth indicator and interlocks | Drill depth indicator |
| Components (2) | Drill Assist Automated Functionality (onboard technology): - Auto Level (with auto retract jacks) - Auto Mast (raise, lower and lock into place) - Auto Dril (single pass) |
Auto level, auto retract, auto mast | Product Link™ Elite (hardware from factory, subscription package via dealer) |
| Components (3) | Cat Terrain ready | Drill assist (single or multipass auto drill) (options) | - |
| Components (4) | Product Link™ Elite | Product Link Elite (hardware from factory, subscription package via dealer) | - |
| Components (6) | - | Wiring for third party interface | - |
| Components (5) | - | Optional Command for Drilling enables each operator to manage more than one machine | - |
| Type | - | Autonomy ready | - |
| Optional Cat Terrain for Drills - Mining System Interface | - | – Production – Navigation |
- |
| Type (2) | - | - | Autonomy ready |
Safety and Security |
|||
| Feature (1) | Approach angle of 15-degrees facilitates loading and unloading on a lowboy | - | - |
| Components (1) | Seven (7) emergency stop buttons | Alloy drill deck covers, with storage provision | Alloy drill deck covers, for servicing when mast is horizontal |
| Components (2) | Hinged window guard over the full length of the front drill window | Seven (7) engine shut down buttons: in cab, at drill deck, on deck at power train, ground accessible by main access point and each side of the drill front and left | Seven (7) engine shut down buttons, by each drill egress/access point, in cab, in engine area, on drill deck |
| Components (3) | Conditional safety interlocks | Electric horn activated by push button in the cab | Over forty (40) conditional safety interlocks |
| Components (4) | Self-closing gates | Tram alarm is automatic and audible | Hinged window guard over the full length of the front drill window |
| Components (5) | Electric horn activated by push button in the cab | Hinged protective guard for full front drill window | Three (3) egress points on deck areas in addition to main access |
| Components (6) | Automatic, audible tram alarm | Guards for exhaust pipes and turbo lines | Self-closing gates secure egress ladder locations |
| Components (7) | Battery disconnect and starter switches can be locked out | Mast access ladder with mast grating (option) | Electric horn activated by push button in the cab |
| Components (8) | Air hose retention devices | Three egress points on deck areas in addition to main access | Automatic tram alarm, audible |
| Components (9) | Slip resistant platform surfaces | Self-closing, gates secure egress ladder locations | Under deck mounted battery box with keyed battery disconnect/starter disconnect/remote jump start terminals |
| Components (10) | Machine lifting provisions | In-deck mounted battery box | Compressor air hoses with safety retention cables |
| Components (11) | FOPS Certified Operator Cab | Ground level keyed battery disconnect/starter lockout with remote jump start terminals | Slip resistant surfaces |
| Components (12) | - | Air hose retention devices | Tow hooks on non-drill-end |
| Feature | - | Approach angle of 14 degrees facilitates loading and unloading on a lowboy | Approach angle of 15 degrees facilitates loading and unloading on a lowboy |
| Components (13) | - | - | Lifting lugs |
Service Packages |
|||
| Package (1) | Basic Package: Centralized manual lubrication for all pivot points, gravity fill for fuel and water | Basic/Manual – Centralized Manual Lube; Gravity Fill for fuel and water | Fast fill for fuel and water, automated lubrication system |
| Package (2) | Standard Package: Automated lubrication system, fast fill for fuel and water (option) | Standard – Fast Fill for fuel and water; Automatic Lubrication System | Service center for lubricant drain and fill, automated lubrication system, fast fill fuel and water, blow down hose (option) |
| Package (3) | Premium Package: Automated lubrication system, fast fill fuel and water, service center for lubricant drain and fill plus blowdown hose (option) | Premium – Service center for lubricant drain and fill (compressor oil, hydraulic oil, gearbox oil, engine oil, tool lubrication and grease), Automatic Lubrication System, Fast Fill for fuel and water, blowdown hose | - |
Weights |
|||
| Working Weight Range | 40 823 - 45 359 kg (90,000 - 100,000 lb) | - | 56 468 kg to 64 154 kg (124,490 lb to 141,436 lb) |
Dimensions (Approximate) - 17.5 m (57.4 ft) Mast |
|||
| Body Length - Standard Cab | - | 43.54 ft | - |
| Length - Mast Down - Extended Cab | - | 83.33 ft | - |
| Length - Mast Down - Standard Cab | - | 81.69 ft | - |
| Width - Front | - | 17.68 ft | - |
| Body Length - Extended Cab | - | 42.24 ft | - |
| Height - Mast Up | - | 77.99 ft | - |
| Width - Rear | - | 20.73 ft | - |
Dimensions (Approximate) - 13.7 m (44.9 ft) Mast |
|||
| Body Length - Standard Cab | - | 43.54 ft | - |
| Body Length - Extended Cab | - | 42.24 ft | - |
| Width - Rear | - | 20.74 ft | - |
| Length - Mast Down - Standard Cab | - | 69.23 ft | - |
| Length - Mast Down - Extended Cab | - | 70.87 ft | - |
| Height - Mast Up | - | 65.39 ft | - |
| Width - Front | - | 17.68 ft | - |
Mast |
|||
| Note (2) | - | Configuration choices include single pass, multi pass, vertical out to 30 degree angle drilling | - |
| Features (12) | - | Pipe catcher; manual or optional hydraulically actuated | - |
| Features (4) | - | Feed system accommodates multiple pipe diameters | - |
| Note (1) | - | Hydraulic, indexing pipe carousels accept various pipe diameters | - |
| Features (13) | - | Tool oiler 113.5 L (30 gal) oil injection system (Rotary drilling only) | - |
| Features (2) | - | Pulldown/hoist system is a single cylinder | - |
| Features (1) | - | 13.7 m (44.9 ft) or 17.5 m (57.4 ft) Mast configurations complete with pipe rack carousel | - |
| Features (9) | - | Drill pipe positioner | - |
| Features (10) | - | Overhead winch with remote; variable speed drive with ≥ 1818 kg (4,000 lb) rating, length to reach 6.1 m (20 ft) past drill deck (option) | - |
| Features (3) | - | Auto tensioning of pull down and hoist cables | - |
| Features (6) | - | Sliding deck wrench assembly | - |
| Features (11) | - | Rotation Gear Box with dual motor arrangement, up to 160 rpm, and 16,000 N∙m of torque (11,800 ft-lb) | - |
| Features (15) | - | Mast access ladder and grating (option) | - |
| Features (5) | - | Variable grip hydraulic break out wrench (HOBO) for range of pipe diameters | - |
| Features (7) | - | Configured with roller deck bushing for tricone applications, two-piece deck bushing for DTH | - |
| Features (14) | - | Mast lanyard mounting provisions (option) | - |
| Features (8) | - | Angle drilling 0-30°; in 5° increments | - |
Engine Choices |
|||
| Components (4) | - | Ether starting aid; ether bottle supplied locally | - |
| Components (2) | - | Scheduled oil sampling (S∙O∙SSM) ports | Ether starting aid (ether bottle supplied locally) |
| Components (1) | - | Dual starter motors | Dual starter motors |
| Components (3) | - | Common air intake filters provide +500 hour service interval in normal operating conditions | - |
| Features | - | - | Scheduled Oil Sampling (S·O·SSM) ports |
| Emissions: Equivalent to U.S. EPA Tier 4 Final - ISO 14396 | - | - | 872 HP |
| Emissions: Equivalent to U.S. EPA Tier 4 Final - ISO 14396 (DIN) | - | - | 884 mhp (PS) |
| Emissions: Equivalent to U.S. EPA Tier 2 - ISO 14396 (DIN) | - | - | 838 mhp (PS) |
| Emissions: Equivalent to U.S. EPA Tier 2 - ISO 14396 | - | - | 826 HP |
| Emissions: Equivalent to U.S. EPA Tier 2 - Engine Power | - | - | C27 @ 1,800 rpm |
| Emissions: Equivalent to U.S. EPA Tier 4 Final - Engine Power | - | - | C27 @ 1,800 rpm |
Dust Suppression Choices |
|||
| Water injection and dry dust collector (option) | - | – Water tank capacity 1514 L (400 gal) – 204 m³/min (7,200 cfm) dry dust collector – Self-cleaning filters, with auto-eject dust chute |
- |
| Water Injection - Standard | - | – Water tank capacity 1514 L (400 gal) | - |
| Choices (1) | - | Dust curtain hydraulic lifters raise front and rear dust curtains (option) (recommended with dust collector) | - |
| Choices (3) | - | Static dust curtains, four sides boxed in (standard) | - |
| High Volume Water Injection System - Not Compatible with Basic Service Package | - | – Water tanks total capacity 3785 L (1,000 gal) maximum – Primary tank above deck – 1514 L (400 gal) capacity (heated for extreme cold weather) – Secondary tank above deck – 2271 L (600 gal) capacity deck |
- |
| Choices (2) | - | Tram off spray to wet the ground around the cuttings pile (not recommended for cold weather applications) | - |
Compressor/Receiver Choices |
|||
| Rotary Drilling (2) | - | 73.6 m³/min (2,600 ft³/min) @ 7.6 bar (110 psi) | - |
| Receiver Tank Choice (1) | - | Low pressure 8.6 bar (125 psi) for ASME/CR N/AU or CE | Low pressure 8.6 bar (125 psi) for ASME/CRN/AU or CE |
| Rotary Drilling (1) | - | 56.6 m³/min (2,000 ft³/min) @ 8.6 bar (125 psi) | - |
| DTH Drilling - Includes Tool Lubrication and Hammer Storage | - | 42.2 m³/min (1,500 ft³/min) @ 34.4 bar (500 psi) | - |
| Note | - | With the compressors variable volume control, the operator can limit air output resulting in reduced fuel consumption – Both high and low pressure compressors contain this feature |
- |
| Receiver Tank Choice (2) | - | High pressure 34.4 bar (500 psi) for ASME/CR N/AU or CE | High pressure 24.1 or 34.4 bar (350 or 500 psi) for ASME/CRN/AU or CE |
| Choice | - | Electronic compressor control and regulation with purged air lines | - |
| Compressor - Rotary Drilling | - | - | 56.6 m³/min (2,000 ft³/min) @ 8.6 bar (125 psi) |
| Compressor - DTH Drilling (1) | - | - | 38.2 m³/min (1,350 ft³/min) @ 34.4 bar (500 psi) |
| Compressor - DTH Drilling (2) | - | - | 42.4 m³/min (1,500 ft³/min) @ 24.1 bar (350 psi) |
| Features (1) | - | - | With the compressor’s variable volume control, the operator can limit air output resulting in reduced fuel consumption |
| Features (2) | - | - | Electronic compressor control and regulation |
| Features (3) | - | - | DTH selection includes tool oiler |
Overhead Winch System (optional) |
|||
| Cable Diameter | - | 0.5 in | - |
| Winch Reach - Past The Drill Deck | - | 20 ft | - |
| Capacity Rating | - | 4000 lb | - |
| Note | - | Variable speed control | - |
Carousel (Mast size and pipe diameter dependent) |
|||
| 13.7 m (44.9 ft) Mast Carousel; holds quantity of 4 × 12.19 m (40 ft) pipes; total depth 62.5 m (204.9 ft): Pipe diameters | - | 178 mm (7 in), 194 mm (7.625 in), 203 mm (8 in), 219 mm (8.625 in) | - |
| 13.7 m (44.9 ft) Mast Carousel; holds quantity of 5 × 12.19 m (40 ft) pipes; total depth 74.6 m (244.9 ft): Pipe diameters | - | 194 mm (7.625 in), 219 mm (8.625 in) | - |
| 17.5 m (57.4 ft) Mast Carousel; holds quantity of 2 × 7.62 m (25 ft) pipes; total depth 32.7 m (107.4 ft): Pipe diameter | - | 9.25 in | - |
| 17.5 m (57.4 ft) Mast Carousel; holds quantity of 4 × 7.62 m (25 ft) pipes; total depth 48 m (157.5 ft): Pipe diameters | - | 178 mm (7 in), 194 mm (7.625 in), 203 mm (8 in), 219 mm (8.625 in) | - |
| Note | - | 13.7 m (44.9 ft) Mast Carousel, dual purpose; holds quantity of two (2) 12.19 m (40 ft) pipes and quantity of two (2) 9.14 m (30 ft) pipes, and adapters to connect to DTH hammer and tricone bit (DTH hammer and tricone not included)
|
- |
| Pipe rack carousel, standard: | - | - | – 11.2 m (36.7 ft) Mast: holds quantity of four (4) 10.6 m (35 ft) pipes – 13.6 m (44.6 ft) Mast: holds quantity of four (4) 6.1 m (20 ft) pipes |
Service Tool Options |
|||
| Option | - | Bushing Retention Tool 178 to 235 mm (7.00 to 9.25 in) pipe diameter | - |
| Lifting Bails (Available on Request) | - | – 114 mm (4.5 in) API reg thread – 140 mm (5.5 in) API reg thread – 168 mm (6.625 in) for top sub/shock sub API thread – 114 mm (4.5 in) for 178 mm (7 in) pipe BECO thread – 152 mm (6 in) for 194 mm (7.625 in) up to 235 mm (9.25 in) pipe BECO |
– API thread 89 mm (3.5 in) – to lift corresponding drill tools (6.75 in tricone bits or 6-inch class DTH hammers) – API thread 114 mm (4.5 in) – to lift corresponding drill tooling (7.875 and 9.0 in tricone bits or 8-inch class DTH hammers) – API t |
Weights - 13.7 m (44.9 ft) Mast |
|||
| Working Weight Range - Minimum/Maximum | - | 75 800/97 000 kg (167,110/213,848 lb) | - |
Hydraulic Break Out Wrench |
|||
| Variable Grip Hydraulic Break Out Wrench Grip Ranges (2) | - | 235 mm (9.25 in) | 152-216 mm (6.0-8.5 in) |
| Variable Grip Hydraulic Break Out Wrench Grip Ranges (1) | - | 178-219 mm (7.0-8.625 in) | 114-152 mm (4.5-6.0 in) |
Weights - 17.5 m (57.4 ft) Mast |
|||
| Working Weight Range - Minimum/Maximum | - | 75 500/97 500 kg (166,449/214,950 lb) | - |
Dimensions (Approximate) - 13.6 m (44.6 ft) Mast |
|||
| Width Non-Cab End | - | - | 15.9 ft |
| Width Cab End | - | - | 18.45 ft |
| Note | - | - | Width and length dimensions include: cascading stairs and walk-around access for cab. |
| Mast Only Shipping Length | - | - | 61.4 ft |
| Height - Mast Up | - | - | 61.13 ft |
| Body Length | - | - | 38.41 ft |
| Length - Mast Down | - | - | 66.17 ft |
| Height - Mast Down | - | - | 16.84 ft |
Dimensions (Approximate) - 11.2 m (36.7 ft) Mast |
|||
| Width Non-Cab End | - | - | 15.9 ft |
| Width Cab End | - | - | 18.45 ft |
| Note | - | - | Width and length dimensions include: cascading stairs and walk-around access for cab. |
| Mast Only Shipping Length | - | - | 53.5 ft |
| Height - Mast Up | - | - | 56.3 ft |
| Body Length | - | - | 38.41 ft |
| Length - Mast Down | - | - | 58.3 ft |
| Height - Mast Down | - | - | 16.84 ft |
Mast and Pipe Rack Carousel Features |
|||
| Features (7) | - | - | Sliding deck wrench assembly |
| 13.6 m (44.6 ft) Mast - Hole Diameter Range: 152-250 mm (6-9.875 in) - Single-Pass Depth | - | - | 44.6 ft |
| Features (5) | - | - | Auto tensioning of pull down and hoist cables |
| 11.2 m (36.7 ft) Mast - Hoist Speed | - | - | 2.65 ft/s |
| Features (3) | - | - | Drill strings configured for bit changes (above the deck) |
| Features (1) | - | - | Mast configurations complete with pipe rack carousel and angle drilling package (vertical, out to 30 degrees in 5-degree increments) |
| Features (8) | - | - | Configured with roller deck bushing for tricone applications, two-piece deck bushing for DTH |
| Features (10) | - | - | Drill pipe positioner |
| Features (11) | - | - | Rotation gear box with single motor up to 160 rpm, up to 11 700 N∙m (8,629 lbf-ft) torque |
| Features (9) | - | - | Closed circuit camera in mast is used to view pipe rack carousel/top drive operation while racking pipes |
| Features (6) | - | - | Variable grip hydraulic break out wrench for range of pipe diameters |
| 11.2 m (36.7 ft) Mast - Hole Diameter Range: 152-250 mm (6-9.875 in) - Multi-Pass Depth | - | - | Down to 53.9 m (Down to 176.7 ft) |
| Features (4) | - | - | Single Hydraulic Cylinder and cable system for pulldown/hoist |
| Features (2) | - | - | Hydraulically actuated, self-indexing pipe rack carousel accepts pipe diameters from 127 mm (5.0 in) to 194 mm (7.625 in) |
| 13.6 m (44.6 ft) Mast - Hole Diameter Range: 152-250 mm (6-9.875 in) - Multi-Pass Depth | - | - | Down to 37.9 m (Down to 124.6 ft) |
| 13.6 m (44.6 ft) Mast - Hoist Speed | - | - | 2.16 ft/s |
| 11.2 m (36.7 ft) Mast - Bit Load (single pass) | - | - | Up to 22 321 kg (Up to 49,210 lb) |
| 11.2 m (36.7 ft) Mast - Pull-Down Capacity | - | - | Up to 20 411 kg (Up to 45,000 lb) |
| 13.6 m (44.6 ft) Mast - Bit Load (single pass) | - | - | Up to 32 655 kg (Up to 71,993 lb) |
| 13.6 m (44.6 ft) Mast - Pull-Down Capacity | - | - | Up to 29 483 kg (Up to 65,000 lb) |
| 13.6 m (44.6 ft) Mast - Hoist Capacity | - | - | Up to 16 584 kg (Up to 36,563 lb) |
| 11.2 m (36.7 ft) Mast - Hoist Capacity | - | - | Up to 15 309 kg (Up to 33,750 lb) |
Add a Similar Product:
There are no similar products.