MD6310 Rotary Blasthole Drill 13.7 m or 17.5 m (44.9 ft or 57.4 ft) Mast Configuration
-
Bit Load
- Up to 42 149 kg (Up to 92,922 lb)
-
Hole Diameter
- 203-311 mm (8-12.25 in)
-
Engine
- C32B® @ 1,800 rpm
-
Body Length - Standard Cab
- 43.54ft
-
Length - Mast Down - Extended Cab
- 83.33ft
-
Length - Mast Down - Standard Cab
- 81.69ft
-
Width - Front
- 17.68ft
-
Body Length - Extended Cab
- 42.24ft
-
Height - Mast Up
- 77.99ft
-
Width - Rear
- 20.73ft
-
13.7 m (44.9 ft) Mast - Hoist Speed
- 122.7ft/min
-
17.5 m (57.4 ft) Mast - Hoist Speed
- 122.7ft/min
-
Emissions (Equivalent to Tier 2): Engine
- C32B @ 1,800 rpm
-
13.7 m (44.9 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Multi Pass Depth
- Down to 74.6 m (Down to 244.9 ft)
-
17.5 m (57.4 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Multi Pass Depth
- Down to 47.9 m (Down to 157.4 ft)
-
17.5 m (57.4 ft) Mast - Pulldown Capacity
- Up to 39 009 kg (Up to 86,000 lb)
-
17.5 m (57.4 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Single Pass Depth
- 57.4ft
-
13.7 m (44.9 ft) Mast - Hole Diameter Range
- 203-311 mm (8-12.25 in)
-
Angle Drilling
- Vertical to 30° (in 5° increments)
-
17.5 m (57.4 ft) Mast - Hole Diameter Range
- 203-311 mm (8-12.25 in)
-
17.5 m (57.4 ft) Mast - Bit Load - Single Pass
- Up to 42 149 kg (Up to 92,922 lb)
-
13.7 m (44.9 ft) Mast - Hoist Capacity
- Up to 22 113 kg (Up to 48,750 lb)
-
Compressor - Rotary Drilling (1)
- 56.6 m³/min (2,000 ft³/min) @ 8.6 bar (125 psi)
-
Compressor - Rotary Drilling (2)
- 73.6 m³/min (2,600 ft³/min) @ 7.6 bar (110 psi)
-
13.7 m (44.9 ft) Mast - Pulldown Capacity
- Up to 39 009 kg (Up to 86,000 lb)
-
13.7 m (44.9 ft) Mast - Hole Diameter Range 203-311 mm (8-12.25 in) - Single Pass Depth
- 44.9ft
-
Emissions (U.S. EPA Tier 4 Final): Engine
- C32B @ 1,800 rpm
-
Compressor - DTH Drilling
- 42.2 m³/min (1,500 ft³/min) @ 34.4 bar (500 psi)
-
17.5 m (57.4 ft) Mast - Hoist Capacity
- Up to 22 113 kg (Up to 48,750 lb)
-
13.7 m (44.9 ft) Mast - Bit Load - Single Pass
- Up to 41 165 kg (Up to 90,753 lb)
-
Emissions (U.S. EPA Tier 4 Final): Power Rating ISO 14396
- 1007HP
-
Emissions (Equivalent to Tier 2): Power Rating ISO 14396
- 1031HP
-
Drawbar Pull
- 122971lbf
-
Track chain guards and guides
- Level two
-
Travel Speed
- 1.5mile/h
-
Lower rollers
- Fourteen (14)
-
Model
- Cat® 349E EL Excavator type
-
Carrier Rollers
- Three (3)
-
Triple grousers for soft rock ground bearing pressure 1.28 bar (18.5 psi)
- 29.5in
-
Components (10)
- In-deck mounted battery box
-
Components (9)
- Self-closing, gates secure egress ladder locations
-
Components (12)
- Air hose retention devices
-
Components (2)
- Seven (7) engine shut down buttons: in cab, at drill deck, on deck at power train, ground accessible by main access point and each side of the drill front and left
-
Components (6)
- Guards for exhaust pipes and turbo lines
-
Feature
- Approach angle of 14 degrees facilitates loading and unloading on a lowboy
-
Components (7)
- Mast access ladder with mast grating (option)
-
Components (4)
- Tram alarm is automatic and audible
-
Components (11)
- Ground level keyed battery disconnect/starter lockout with remote jump start terminals
-
Components (1)
- Alloy drill deck covers, with storage provision
-
Components (5)
- Hinged protective guard for full front drill window
-
Components (3)
- Electric horn activated by push button in the cab
-
Components (8)
- Three egress points on deck areas in addition to main access
-
Components (10)
- Filter indicators for hydraulic, compressor and engine
-
Components (14)
- ECM controlled proportional fan speed control system
-
Components (23)
- Data logging of machine health with warnings, and fault code records; export capability
-
Components (20)
- Cabin pressure manometer with indicator (option)
-
Components (3)
- Rotation torque control
-
Components (12)
- Dust suppression control
-
Components (17)
- Tram interlock, mast up and locked or down and parked
-
Components (1)
- All electric controls for drilling, tramming, leveling plus auxiliary functions
-
Components (22)
- Prewired for Terrain and autonomous operation
-
Components (8)
- Delayed engine shut down
-
Components (19)
- Cab environment controls (AC, filter, heat, fan speeds)
-
Components (7)
- Drill performance and display system
-
Components (13)
- Mast lock indicator
-
Components (6)
- Drill depth meter
-
Components (2)
- Electronic compressor control
-
Components (4)
- Virtual rotary head travel stops and interlocks
-
Components (11)
- Jack pressure sensors in the display
-
Components (5)
- Pipe positioner engaged/disengaged indicator
-
Components (18)
- Tram interlock, jacks retracted
-
Components (16)
- Tram interlock, pipe in hole
-
Components (21)
- Dust curtain lifting system – auto hydraulic raise front and rear (option)
-
Components (15)
- Tram interlock, machine stability limits
-
Components (9)
- Rotary head rpm gauge – (digital display in screen)
-
Body Length - Standard Cab
- 43.54ft
-
Body Length - Extended Cab
- 42.24ft
-
Width - Rear
- 20.74ft
-
Length - Mast Down - Standard Cab
- 69.23ft
-
Length - Mast Down - Extended Cab
- 70.87ft
-
Height - Mast Up
- 65.39ft
-
Width - Front
- 17.68ft
-
Note (2)
- Configuration choices include single pass, multi pass, vertical out to 30 degree angle drilling
-
Features (12)
- Pipe catcher; manual or optional hydraulically actuated
-
Features (4)
- Feed system accommodates multiple pipe diameters
-
Note (1)
- Hydraulic, indexing pipe carousels accept various pipe diameters
-
Features (13)
- Tool oiler 113.5 L (30 gal) oil injection system (Rotary drilling only)
-
Features (2)
- Pulldown/hoist system is a single cylinder
-
Features (1)
- 13.7 m (44.9 ft) or 17.5 m (57.4 ft) Mast configurations complete with pipe rack carousel
-
Features (9)
- Drill pipe positioner
-
Features (10)
- Overhead winch with remote; variable speed drive with ≥ 1818 kg (4,000 lb) rating, length to reach 6.1 m (20 ft) past drill deck (option)
-
Features (3)
- Auto tensioning of pull down and hoist cables
-
Features (6)
- Sliding deck wrench assembly
-
Features (11)
- Rotation Gear Box with dual motor arrangement, up to 160 rpm, and 16,000 N∙m of torque (11,800 ft-lb)
-
Features (15)
- Mast access ladder and grating (option)
-
Features (5)
- Variable grip hydraulic break out wrench (HOBO) for range of pipe diameters
-
Features (7)
- Configured with roller deck bushing for tricone applications, two-piece deck bushing for DTH
-
Features (14)
- Mast lanyard mounting provisions (option)
-
Features (8)
- Angle drilling 0-30°; in 5° increments
-
Components (4)
- Ether starting aid; ether bottle supplied locally
-
Components (2)
- Scheduled oil sampling (S∙O∙SSM) ports
-
Components (1)
- Dual starter motors
-
Components (3)
- Common air intake filters provide +500 hour service interval in normal operating conditions
-
Package (1)
- Basic/Manual – Centralized Manual Lube; Gravity Fill for fuel and water
-
Package (2)
- Standard – Fast Fill for fuel and water; Automatic Lubrication System
-
Package (3)
- Premium – Service center for lubricant drain and fill (compressor oil, hydraulic oil, gearbox oil, engine oil, tool lubrication and grease), Automatic Lubrication System, Fast Fill for fuel and water, blowdown hose
-
Water injection and dry dust collector (option)
- – Water tank capacity 1514 L (400 gal)
– 204 m³/min (7,200 cfm) dry dust collector
– Self-cleaning filters, with auto-eject dust chute
-
Water Injection - Standard
- – Water tank capacity 1514 L (400 gal)
-
Choices (1)
- Dust curtain hydraulic lifters raise front and rear dust curtains (option) (recommended with dust collector)
-
Choices (3)
- Static dust curtains, four sides boxed in (standard)
-
High Volume Water Injection System - Not Compatible with Basic Service Package
- – Water tanks total capacity 3785 L (1,000 gal) maximum
– Primary tank above deck – 1514 L (400 gal) capacity (heated for extreme cold weather)
– Secondary tank above deck – 2271 L (600 gal) capacity deck
-
Choices (2)
- Tram off spray to wet the ground around the cuttings pile (not recommended for cold weather applications)
-
Components (4)
- Top Sub, or Shock sub and cross over adapter (option)
-
Components (3)
- Deck wrench, sliding
-
Components (5)
- Bit sub
-
Components (1)
- Roller deck bushing
-
Components (6)
- Pipe wiper seal
-
Components (2)
- Pipe positioner inserts
-
Rotary Drilling (2)
- 73.6 m³/min (2,600 ft³/min) @ 7.6 bar (110 psi)
-
Receiver Tank Choice (1)
- Low pressure 8.6 bar (125 psi) for ASME/CR N/AU or CE
-
Rotary Drilling (1)
- 56.6 m³/min (2,000 ft³/min) @ 8.6 bar (125 psi)
-
DTH Drilling - Includes Tool Lubrication and Hammer Storage
- 42.2 m³/min (1,500 ft³/min) @ 34.4 bar (500 psi)
-
Note
- With the compressors variable volume control, the operator can limit air output resulting in reduced fuel consumption
– Both high and low pressure compressors contain this feature
-
Receiver Tank Choice (2)
- High pressure 34.4 bar (500 psi) for ASME/CR N/AU or CE
-
Choice
- Electronic compressor control and regulation with purged air lines
-
Components (5)
- Four (4) lift lugs, for use with cables or chains
-
Components (7)
- Bit storage box in-deck with hinged cover (option)
-
Components (6)
- Walkway around cab to drill deck (option)
-
Features (2)
- Slip resistant surface
-
Features (3)
- Fuel tank capacity 1609 L (425 gal)
-
Components (1)
- Stationary rear deck; for vertical and angle drilling
-
Components (2)
- Four leveling jacks to provide leveling on a 7° bench (any orientation)
-
Features (6)
- Three egress points on deck areas in addition to main access
-
Components (10)
- Drill pipe thread greaser with remote fill tank or disposable grease bucket (option)
-
Features (7)
- Sturdy guardrails, toe guards, self closing gates
-
Components (4)
- Heavy duty tow hooks (front end)
-
Components (3)
- Manual, centralized, lubrication banks for all pivot points on drill, or automated lubrication system (option)
-
Components (8)
- DTH hammer storage on drill deck with high pressure configuration (option)
-
Features (4)
- Fuel capacity expansion for additional +1609 L (425 gal)
-
Features (5)
- Bolt-on platform for cold weather generator or fire suppression bottles (option)
-
Components (9)
- Hydraulically operated viewing hatch in drill deck with spotlight (option)
-
Features (1)
- Jacks, mast pivot and deck are welded integrally to mainframe for maximum durability and long life
-
Components (2)
- Separate engine cooling module
-
Components (1)
- Coolers with easy cleaning access
-
Components (3)
- Replaceable cooler core sections
-
Components (4)
- Automatic variable speed fan control
-
Features
- Functional in ambient temperature of 52° C (125° F)
-
Components (6)
- Wiring for third party interface
-
Components (3)
- Drill assist (single or multipass auto drill) (options)
-
Components (5)
- Optional Command for Drilling enables each operator to manage more than one machine
-
Type
- Autonomy ready
-
Components (2)
- Auto level, auto retract, auto mast
-
Components (1)
- Drill depth indicator and interlocks
-
Optional Cat Terrain for Drills - Mining System Interface
- – Production
– Navigation
-
Components (4)
- Product Link Elite (hardware from factory, subscription package via dealer)
-
7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary (1)
- 8in
-
7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: DTH
- 7in
-
7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary or DTH
- 7.625in
-
7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary (2)
- 8.625in
-
7.62 m (25 ft) pipes - pipe rack carousel holds a quantity of four or five pipes, 17.5 m (57.4 ft) Mast: Rotary
- 9.25in
-
12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary (2)
- 8.625in
-
12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary (1)
- 8in
-
12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: DTH
- 7in
-
12.19 m (40 ft) pipes - pipe rack carousel holds a quantity of four (4) or five (5) pipes, 13.7 m (44.9 ft) Mast: Rotary or DTH
- 7.625in
-
Note
- Dual purpose carousel pipe: 13.7 m (44.9 ft) Mast; holds quantity of two (2) 12.19 m (40 ft) pipes and quantity of two (2) 9.14 m (30 ft) pipes, and adapters to connect to DTH hammer and tricone bit (DTH hammer and tricone not included)
-
Climate Level 2 Arctic Fluids and Lubricants
- Rated down to –18° C (–0.4° F) temperatures
-
Climate Level 1 Standard Fluids and Lubricants (1)
- Rated down to –1° C (30° F) temperatures
-
Climate Level 1 Standard Fluids and Lubricants (2)
- Withstands high heat to 52° C (125° F)
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (6)
- Breaker panel includes five (5) additional breakers for locally supplied heating elements, if needed
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (3)
- Full arctic lubricant package includes: engine oil, compressor oil and hydraulic oil
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (1)
- Rated down to –40° C (–40° F) temperatures
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (5)
- Shore power connection box with switchable 240-600V (50 amp) connection; diesel genset and or plug, sold separately
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (2)
- Diesel fired heating system that heats and circulates engine coolant through the: engine block, primary water tank, heating elements for battery trays with a provision for fuel tanks
-
Climate Level 4 Arctic Fluids and Lubricants, Heating Package (4)
- Electric heating package with breaker panel to power: 120V heating blanket for compressor receiver tank, compressor control box, heat trace for compressor control lines, heat trace for housing from water tank to water pump and water fast-fill assembly plu
-
Cable Diameter
- 0.5in
-
Winch Reach - Past The Drill Deck
- 20ft
-
Capacity Rating
- 4000lb
-
Note
- Variable speed control
-
Lighting
- – LED interior lights; separate reading light, and backlit joysticks and keypads
– Zone controls for area lights and spot lighting for night drilling
– Flood lights for the drill perimeter
– Spot lights for power group area; drill deck; mast caro
-
Components (7)
- Operator station design integrates an ergonomic seat, armchair joystick controls with full instrumentation, and two 254 mm (10 in) color, high definition touchscreens and 12 volt power port
-
Components (4)
- Drill performance touchscreen display
-
Components (3)
- Cab perimeter walkway available for both cab sizes
-
Components (1)
- Spacious FOPS cab has 3 m² (32.4 ft²) floor space with an integrated operator station
-
Components (13)
- Seat swivels, locks and has two point/76 mm (3 in) seat belt, tilts (5° adjustment), lumbar support, fore/aft seat adjustment 80 mm (3.1 in)
-
Components (9)
- Power convertor 24V to 12V
-
Components (2)
- Extended cab option 4.2 m² (45.2 ft²); prewired and dedicated space for refrigerator and microwave
-
HVAC
- – Floor vents in the foot rest area
– Roof-mounted air conditioner/heating/pressurizing unit
– Filter access from deck, does not require roof access, and has approximately 500 hour service interval
– Defogging HVAC vents on driller window
-
Components (6)
- Two swing-out hinged doors with windows and Cat keyed locks
-
Components (14)
- Trainer’s seat that folds away and has retractable seat belt (optional)
-
Cameras
- – Mounted on the front and left sides to provide 360° view from operator's seat
– Camera on the mast to view pipe carousel/top drive operation
-
Components (5)
- Cab rubber shock-mounts absorb mechanical vibration and restrict exterior noise
-
Components (10)
- Radio-ready for communication and entertainment radio
-
Cab - Premium
- – Leather seat with heat and ventilation
– Dual pane window glass
– Front window guard
– Additional in-cab storage box
– Additional windshield wipers on front and rear windows
– Window shades (option)
– Foldaway trainer’s seat (option)
-
Components (11)
- Cab roof access ladder (option)
-
Cab - Standard
- – Fabric seat
– Single pane window glass
– Windshield wiper for driller window
– Window shades (option)
– Foldaway trainer’s seat (option)
– Removable floor mat
-
Components (8)
- Additional display screen for cc cameras; color, high-definition 254 mm (10 in)
-
Components (12)
- Literature holder
-
Components (4)
- Virtual rotary head travel stops and interlocks
-
Components (3)
- Rotary torque control
-
Components (2)
- Rotation gear box with dual motor arrangement, up to 160 rpm, and 16 000 N∙m (11,800 lbf-ft) of torque
-
Components (1)
- Spindle with 168 mm (6.625 in) API regular thread and splined collar
-
Components (2)
- One (1) auxiliary circuit pump – 110 cc (piston, load sensing)
-
Components (3)
- Two (2) fan pumps – 1,000 cc (piston, with proportional electronic controls)
-
Components (1)
- Two (2) primary pumps – 210 cc (piston, with proportional electronic controls)
-
Components (4)
- Two (2) charge pumps – 43.9 + 56.5 cc (double stack gear, fixed displacement)
-
Components (5)
- Scheduled Oil Sampling (S∙O∙S) ports
-
Components (1)
- Two piece bushing
-
Components (6)
- Pipe wiper seal
-
Components (4)
- Shock sub and top sub adapter
-
Components (5)
- Cross over hammer adapter
-
Components (3)
- Deck wrench, sliding
-
Components (2)
- Pipe positioner inserts
-
Choice (1)
- Fixed access ladder to the cab area
-
Choice (3)
- Cab perimeter walkway available with either choice
-
Choice (2)
- Cascading, hydraulic stairs to cab area (option) – includes jack and tram interlock that activates when the stairs are down
-
Mast Accessories Hydraulic (2)
- One hydraulic pipe catcher, plus one wire rope, hydraulically actuated pipe positioner, hydraulic bit basket
-
Mast Accessories Hydraulic (1)
- One hydraulic pipe catcher, hydraulically actuated pipe positioner, hydraulic bit basket
-
Angle Drilling
- Included with either mast
-
Mast Accessories Manual, 17.5 m (57.4 ft) Mast
- Two wire rope pipe catchers, hydraulically actuated pipe positioner, manual bit basket
-
Mast Accessories Manual, 13.7 m (44.9 ft) Mast
- One wire rope pipe catcher, hydraulically actuated pipe positioner, manual bit basket
-
13.7 m (44.9 ft) Mast Carousel; holds quantity of 4 × 12.19 m (40 ft) pipes; total depth 62.5 m (204.9 ft): Pipe diameters
- 178 mm (7 in), 194 mm (7.625 in), 203 mm (8 in), 219 mm (8.625 in)
-
13.7 m (44.9 ft) Mast Carousel; holds quantity of 5 × 12.19 m (40 ft) pipes; total depth 74.6 m (244.9 ft): Pipe diameters
- 194 mm (7.625 in), 219 mm (8.625 in)
-
17.5 m (57.4 ft) Mast Carousel; holds quantity of 2 × 7.62 m (25 ft) pipes; total depth 32.7 m (107.4 ft): Pipe diameter
- 9.25in
-
17.5 m (57.4 ft) Mast Carousel; holds quantity of 4 × 7.62 m (25 ft) pipes; total depth 48 m (157.5 ft): Pipe diameters
- 178 mm (7 in), 194 mm (7.625 in), 203 mm (8 in), 219 mm (8.625 in)
-
Note
- 13.7 m (44.9 ft) Mast Carousel, dual purpose; holds quantity of two (2) 12.19 m (40 ft) pipes and quantity of two (2) 9.14 m (30 ft) pipes, and adapters to connect to DTH hammer and tricone bit (DTH hammer and tricone not included)
-
Option
- Bushing Retention Tool 178 to 235 mm (7.00 to 9.25 in) pipe diameter
-
Lifting Bails (Available on Request)
- – 114 mm (4.5 in) API reg thread
– 140 mm (5.5 in) API reg thread
– 168 mm (6.625 in) for top sub/shock sub API thread
– 114 mm (4.5 in) for 178 mm (7 in) pipe BECO thread
– 152 mm (6 in) for 194 mm (7.625 in) up to 235 mm (9.25 in) pipe BECO
-
Working Weight Range - Minimum/Maximum
- 75 800/97 000 kg (167,110/213,848 lb)
-
Variable Grip Hydraulic Break Out Wrench Grip Ranges (2)
- 235 mm (9.25 in)
-
Variable Grip Hydraulic Break Out Wrench Grip Ranges (1)
- 178-219 mm (7.0-8.625 in)
-
Working Weight Range - Minimum/Maximum
- 75 500/97 500 kg (166,449/214,950 lb)
Optional Equipment:
-
- Frame
-
- Fuel tank expansion of +1609 L (425 gal) for total of 3218 L (850 gal) (option) required for autonomy packages
-
- Mast
-
- Overhead winch with remote; variable speed drive with ≥ 1814 kg (4,000 lb) rating, length to reach 6.1 m (20 ft) past drill deck
- Rotary tool lubrication, 113.5 L (30 gal) oil injection system
- Mast access ladder, mast grating and lanyard posts
-
- Operator Environment
-
- Trainer seat that folds away
- Window shades
- Cabin pressure manometer gauge
- Cab roof access ladder
-
- Service Tool Options
-
- Bushing Retention Tool 178 to 235 mm (7 to 9.250 in) pipe diameter
- Lifting bails (available on request; required for commissioning)
– 114 mm (4.5 in) API reg thread
– 140 mm (5.5 in) API reg thread
– 168 mm (6.625 in) for top sub/shock sub API reg thread
– 114 mm (4.5 in) for 178 mm (7 in) pipe BECO thread
– 152 mm (6 in) for 194 mm (7.625 in) up to 235 mm (9.25 in) pipe BECO thread
-
- Technology Products
-
- Product Link Elite – cellular
- Product Link Elite – Dual (cellular and satellite)
- Terrain for Drilling
-
- Ground Engaging Tools
-
- Drill bits, rotary tricone
– 228 mm (9.0 in), OPT 1, (S3)
– 228 mm (9.0 in), OPT 2, (M2)
– 228 mm (9.0 in), OPT 3, (H1)
– 251 mm (9.875 in), OPT 1, (M1)
– 251 mm (9.875 in), OPT 2, (M3)
– 251 mm (9.875 in), OPT 3, (H1)
– 270 mm (10.625 in), OPT 1, (S3)
– 270 mm (10.625 in), OPT 2, (M3)
– 270 mm (10.625 in), OPT 3, (H1)
– 311 mm (12.25 in), OPT 1, (M1)
– 311 mm (12.25 in), OPT 2, (M3)
– 311 mm (12.25 in), OPT 3, (H1)
-
- Dust Suppression
-
- Dust curtain hydraulic lifters raise front and rear dust curtains (recommended with dust collector)
- Tram off spray system
-
- Drill Pipe
-
- 12.19 m (40 ft) Pipes, 13.7 m (44.9 ft) Mast – Carousel holds quantity of four
– DTH – 178 mm (7 in)
– Rotary/DTH – 194 mm (7.625 in)
– Rotary – 203 mm (8 in)
– Rotary – 219 mm (8.625 in)
- 7.62 m (25 ft) Pipes, 17.5 m (57.4 ft) Mast – Carousel holds quantity of four
– DTH – 178 mm (7 in)
– Rotary/DTH – 194 mm (7.625 in)
– Rotary – 203 mm (8 in)
– Rotary – 219 mm (8.625 in)
– Rotary – 235 mm (9.25 in) Carousel accepts quantity of two
- 9.14 m (30 ft) pipes, 13.7 m (44.9 ft) Mast – Carousel holds quantity of two with special sub adapters to connect to DTH hammer and tricone bit (DTH hammer and tricone not included)
– Accepts 194 mm (7.625 in) pipe
- Contact factory for additional pipe diameters
Compare Products