CALL US: 800-937-2326   |   PARTS: 800-937-2311   |   LOCATIONS
  • Home
  • Compare

    • Compare Equipment Go Back

    D7 Dozer
    View Product
    854 Wheel Dozer
    View Product Remove
    D10 Dozer
    View Product Remove

    Engine
    Engine Model Cat C9.3B Cat C32B -
    Power - Net 265 HP - -
    Net Power - Rated - ISO 9249/SAE J1349 265 HP - -
    Net Power (Rated) - ISO 9249 (DIN) 268 mhp - -
    Emissions U.S. EPA Tier 4 Final/EU Stage V/Japan 2014/Korea Stage V/China Nonroad Stage IV - -
    Note (1) Net power at 2,200 rpm. Net power advertised is the power available at the engine flywheel when the engine is equipped with a fan, air cleaner, clean emissions module and alternator. Advertised power is tested per the specified standard in effect at the t Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler and alternator. -
    Note (2) Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: 20% biodiesel FAME (fatty acid methyl ester) ** or 100% renewable diesel, HVO ( Net torque rise meets SAE J139. -
    Note (3) Basic machine specs provided below. For complete specifications and dimensions by configuration, blade and track shoe offerings and more, please visit the product download section to view the full Technical Specifications document. No engine derating required up to 3050 m (10,000 ft) altitude. -
    Note (4) Machine Build Number 17A - -
    Gross Power - 907 HP -
    Emissions (U.S. EPA Tier 4 Final): Gross Power - SAE J1995 - 900 HP -
    Emissions (U.S. EPA Tier 4 Final): Net Power ISO - 9249 - 814 HP -
    Emissions (Tier 2 Equivalent): Gross Power - SAE J1995 - 907 HP -
    Emissions (Tier 2 Equivalent): Net Power ISO - 9249 - 823 HP -
    Rated Speed - 1750 r/min -
    Bore - 5.7 in -
    Stroke - 6.4 in -
    Displacement - 1958 in² -
    Peak Torque - 1,200 rpm - 3139 lb/ft -
    Torque Rise - 30 % -

    Weights
    Operating Weight 65644 lb 224647 lb 154888 lb
    Note (1) Standard SU operating weight includes ripper with three shanks adding approximately 2993 kg/6596 lbs. LGP S operating weight with drawbar. - D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.
    Shipping Weight - - 111739 lb
    Note (2) - - D10 Shipping Weight includes coolant, lubricants, 10% fuel, FOPS cab, fast fuel, and 610 mm (24 in) ES shoes.

    Transmission
    Power Train Fully Automatic 4-Speed - -
    Transmission Type - Cat Planetary Power Shift -
    Converter Drive - Forward 1 - 4.4 mile/h -
    Converter Drive - Forward 2 - 7.7 mile/h -
    Converter Drive - Forward 3 - 13.2 mile/h -
    Converter Drive - Reverse 1 - 4.8 mile/h -
    Converter Drive - Reverse 2 - 8.4 mile/h -
    Converter Drive - Reverse 3 - 14.6 mile/h -
    Direct Drive - Forward 1 - Lock-up disabled -
    Direct Drive - Forward 2 - 8.1 mile/h -
    Direct Drive - Forward 3 - 14.2 mile/h -
    Direct Drive - Reverse 1 - 5 mile/h -
    Direct Drive - Reverse 2 - 8.9 mile/h -
    Direct Drive - Reverse 3 - 15.6 mile/h -
    Note - Travel speeds based on 45/65-45 L-5 46 ply tires. -
    1.0 Forward - - 2.5 mile/h
    1.5 Forward - - 3.4 mile/h
    2.0 Forward - - 4.5 mile/h
    2.5 Forward - - 6 mile/h
    3.0 Forward - - 7.8 mile/h
    1.0 Reverse - - 3.2 mile/h
    1.5 Reverse - - 4.2 mile/h
    2.0 Reverse - - 5.6 mile/h
    2.5 Reverse - - 7.5 mile/h
    3.0 Reverse - - 9.8 mile/h
    Transmission Clutch Diameter - - 17 in
    Type - - Planetary powershift

    Service Refill Capacities
    Fuel Tank 123 gal (US) - -
    DEF Tank 12 gal (US) - -
    Fuel Tank - Standard - 413 gal (US) -
    Cooling System - 53 gal (US) -
    Crankcase - 32 gal (US) -
    Transmission - 45 gal (US) -
    Differential - Final Drives - Front - 98 gal (US) -
    Differential - Final Drives - Rear - 90 gal (US) -
    Hydraulic System - Steering and Engine Cooling Fan - Tank Only - 77 gal (US) -
    Note (1) - - All nonroad U.S. EPA Tier 4, European Union (EU) Stage IIIB and V, and Japan (MLIT) Step 4 diesel engines are required to use only Ultra Low Sulfer Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfer or less. Biodiesel blends up to B20 (20% blend by vo -

    Standard SU
    Operating Weight 65644 lb - -
    Ground Pressure 10 psi - -
    Width of Standard Shoe 24 in - -
    Blade Semi-Universal (SU) - -
    Blade Capacity 10 yd³ - -

    LGP S
    Operating Weight 63220 lb - -
    Ground Pressure 6 psi - -
    Width of Standard Shoe 36 in - -
    Blade Straight (S) - -
    Blade Capacity 8 yd³ - -

    Waste Handler
    Operating Weight 62035 lb - -
    Ground Pressure 10 psi - -
    Width of Standard Shoe 24 in - -
    Blade Universal Landfill (U) - -
    Blade Capacity 22 yd³ - -

    Sustainability
    Recyclability 98% - -

    Air Conditioning System
    Air Conditioning The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.36 kg of refrigerant which has a CO2 equivalent of 1.946 metric tonnes. The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.600 metric tonnes.

    Note (2) Configurations and features may vary by region. Please consult your Cat dealer for availability in your area. - -

    Hydraulic System - Lift/Tilt
    Output at 1,850 rpm and 6900 kPa (1,000 psi) - 161 gal/min -
    Cylinders, Double Acting - Lift, Bore and Stroke - 177 mm × 1760 mm (0.58 ft × 5.8 ft) -
    Cylinder, Double Acting - Tilt and Tip, Bore and Stroke - 267 mm × 286 mm (0.88 ft × 0.94 ft) -

    Axles
    Front - Fixed -
    Rear - Trunnion -

    Brakes
    Brakes - Meets ISO 3540:2011 -

    Blades
    Blade Capacities - 30.5 to 44.8 m3 (40 to 58.6 yd3) -
    10SU ABR - Capacity (SAE J1265) - - 24.2 yd³
    10SU ABR - Width (over end bits) - - 194.5 in
    10SU ABR - Height - - 83.5 in
    10SU ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry) - - 19.98 in
    10SU ABR - Digging Depth - Blade Pitch: Nominal - - 25.23 in
    10SU ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread) - - 30.08 in³
    10SU ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry) - - 66.14 in
    10SU ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread) - - 53.86 in
    10SU ABR - Ground Clearance - Maximum Tilt LH - - 56.3 in
    10SU ABR - Ground Clearance - Maximum Tilt RH - - 56.3 in
    10U ABR - Capacity (SAE J1265) - - 28.7 yd³
    10U ABR - Width (over end bits) - - 207.1 in
    10U ABR - Height - - 83.5 in
    10U ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry) - - 19.98 in
    10U ABR - Digging Depth - Blade Pitch: Nominal - - 60 in
    10U ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread) - - 30.1 in
    10U ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry) - - 66.1 in
    10U ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread) - - 53.9 in
    10U ABR - Ground Clearance - Maximum Tilt LH - - 60.8 in
    10U ABR - Ground Clearance - Maximum Tilt RH - - 60.8 in
    10U ABR - Weights - Blade Weight* - - 23585 lb
    10U ABR - Weights - Total Operating Weight** (with blade and SS ripper) - - 154888 lb
    Note (1) - - Maximum LH and RH tilt for 10SU ABR and 10U ABR blades: 17.31 degrees
    Note (2) - - *Does not include hydraulic controls but includes blade cylinders, pusharms.
    Note (3) - - **D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.

    Dimensions (Approximate)
    Height - Top of ROPS - 18.25 ft -
    Height - Top of Exhaust Pipe - 17.17 ft -
    Height - Top of Hood - 13 ft -
    Ground Clearance - 27 in -
    Centerline of Front Axle to Hitch - 9.67 ft -
    Centerline of Rear Axle to Edge of Bumper - 13.75 ft -
    Wheel Base - 19.25 ft -
    Length - With Blade on Ground - 44 ft -
    Ground Clearance* - - 28.5 in
    Track Gauge - - 100.4 in
    Width - Without Trunnions - 610 mm/24 in ES - - 130.4 in
    Width - Over Trunnions - - 148 in
    Height - FOPS Cab* - - 162.8 in
    Height - Top of Stack* - - 171.5 in
    Height - ROPS/Canopy* - - 173.5 in
    Note (1) - - *Includes grouser height for total dimensions on hard surfaces.
    Length - Track on Ground - - 152.8 in
    Overall Length - Basic Tractor - - 209.6 in
    Length - With SU-Blade - - 292 in
    Length - With U-Blade - - 305.1 in
    Length - With Single-Shank Ripper - - 278.8 in
    Length - With Multi-Shank Ripper - - 285.1 in
    Overall Length - SU-Blade/SS Ripper - - 360.6 in

    Hydraulic System - Steering
    Steering System - Pump - Piston, variable displacement -
    Minimum Turning Radius - Over Blade - 31 ft -
    Steering System - Circuit - Pilot, load sensing -
    Total Steering Angle - 86 degrees -
    Relief Valve Setting - 5004 psi -

    Operating Specifications
    Operating Weight - 224647 lb -

    Sound Performance Levels
    Sound Performance - • The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • The operator sound pressure level was measured according to ISO 6396:2008. The measurement was -

    Cab
    ROPS/FOPS - ISO 3471:2008 and ISO 3449:2005 Level II Standards -

    Engine - U.S. EPA Tier 4 Final/EU Stage V
    Engine Model - - Cat® C27
    Engine Power - Net SAE J1349/ISO 9249** - Forward - - 602 HP
    Engine Power - Gross SAE J1995* - Forward - - 631 HP
    Engine Power - Gross SAE J1995* - Reverse - - 766 HP
    Engine Power - ISO 14396* - Forward - - 620 HP
    Engine Power - ISO 14396* - Reverse - - 754 HP
    Engine Power - Net SAE J1349/ISO 9249** - Reverse - - 722 HP
    Displacement - - 1648 in³
    Stroke - - 6 in
    Bore - - 5.4 in
    Emissions - - U.S. EPA Tier 4 Final/EU Stage V
    Note (1) - - *Excludes all fan losses.
    Note (2) - - All Engine ratings apply at 1,800 rpm.
    Note (3) - - Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
    Note (4) - - Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
    Note (5) - - **Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.

    Undercarriage
    Shoe Type - - Extreme Service (ES)
    Width - Shoe - - 24 in
    Shoes/Side - - 44
    Grouser Height - - 3.7 in
    Pitch - - 10.2 in
    Ground Clearance - - 28.5 in
    Track Gauge - - 100.4 in
    Length - Track on Ground - - 152.8 in
    Ground Contact Area - - 7347 in²
    Track Rollers/Side - - 8
    Number of Carrier Rollers - - 1 per side (optional)

    Standards
    ROPS - - Rollover Protective Structure (ROPS) meets the following criteria: ISO 3471:2008.
    FOPS - - Falling Object Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 LEVEL II.
    Sound - - Operator Sound Pressure Level (ISO 6396:2008): 78 db(A)
    Note - - The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds. The measurement was conducted with the cab doors and the cab windows closed. The cab was properly installed and
    Sound (1) - - Exterior Sound Pressure Level (ISO 6395:2008): 116 db(A)
    Note (1) - - The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds.
    Note (2) - - The sound levels listed above include both measurement uncertainty and uncertainty due to production variation.
    Note (3) - - The available sound suppression package can reduce the dynamic exterior sound power level of the machine by up to 4 db(A) and the dynamic operator sound pressure level by up to 2 db(A).

    Steering and Brakes
    Steering Type - - Hydraulically Applied Multiple-Disc Steering Clutch
    Brake Type - - Spring Applied Multiple- Disc Brake
    Brake Diameter - - 15.4 in
    Brake Count - - 10

    Ripper - Single Shank
    Maximum penetration force * (shank vertical) - - 49233 lbf
    Maximum penetration depth (standard tip) - - 59.2 in
    Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole - - 36 in
    Weight - - 14209 lb
    Note - - Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.

    Ripper - Single Shank, Deep Ripping
    Maximum penetration force * (shank vertical) - - 53055 lbf
    Maximum penetration depth (standard tip) - - 78.3 in
    Weight - - 14548 lb
    Note - - Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.

    Engine - U.S. EPA Tier 2 Equivalent
    Engine Model - - Cat® C27
    Engine Power - Net SAE J1349/ISO 9249** - Forward - - 603 HP
    Engine Power - Net SAE J1349/ISO 9249** - Reverse - - 722 HP
    Engine Power - Gross SAE J1995* - Forward - - 631 HP
    Engine Power - Gross SAE J1995* - Reverse - - 766 HP
    Engine Power - ISO 14396* - Forward - - 622 HP
    Engine Power - ISO 14396* - Reverse - - 756 HP
    Displacement - - 1648 in³
    Bore - - 5.4 in
    Stroke - - 6 in
    Emissions - - U.S. EPA Tier 2 Equivalent
    Note (1) - - *Excludes all fan losses.
    Note (2) - - All Engine ratings apply at 1,800 rpm.
    Note (3) - - Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
    Note (4) - - Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
    Note (5) - - **Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.

    Fuel Tank Capacities
    Fuel Tank - Usable Volume - - 323.3 gal (US)
    Fuel Tank - Total Volume - - 335.2 gal (US)

    Hydraulic Controls
    Pump Type - - Variable displacement piston
    Pump Output - Implement - - 112 gal/min
    Note (1) - - Implement Pump output measured are 2,010 engine rpm and 7000 kPa (1,015 psi).
    Fan Pump - - 21.7 gal/min
    Note (2) - - Fan Pump output measured at 2,010 engine rpm and 26 000 kPa (3,771 psi).
    Tilt Cylinder Flow - Rod End Flow - - 112 gal/min
    Tilt Cylinder Flow - Head End Flow - - 63.4 gal/min
    Lift Cylinder Relief Valve Setting - - 4061.1 psi
    Tilt Cylinder Relief Valve Setting - - 3872.5 psi
    Ripper - Lift - Relief Valve Setting - - 4061.1 psi
    Ripper - Pitch - Relief Valve Setting - - 4061.1 psi
    Tank Capacity - - 32.2 gal (US)
    Cylinder Sizing - Blade Lift - Bore - - 5.5 in
    Cylinder Sizing - Blade Tilt - Bore - - 8.3 in
    Cylinder Sizing - Ripper Shank Lift - Bore - - 8.3 in
    Cylinder Sizing - Ripper Shank Angle - Bore - - 7.1 in
    Cylinder Sizing - Blade Lift - Stroke - - 65.1 in
    Cylinder Sizing - Blade Tilt - Stroke - - 9.5 in
    Cylinder Sizing - Ripper Shank Lift - Stroke - - 21.1 in
    Cylinder Sizing - Ripper Shank Angle - Stroke - - 26 in
    Note (3) - - Electro-hydraulic pilot valves assist operations of ripper and dozer controls.

    FLUID CAPACITIES
    Cooling System Refill – Tier 4 Final Engine - - 46.2 gal (US)
    Engine Crankcase Sump - - 27.2 gal (US)
    Power Train - Total Volume - - 81.4 gal (US)
    Power Train - Refill Volume - - 74.8 gal (US)
    Final Drives (each) - - 12.2 gal (US)
    Track Roller Frames (each) - - 16.9 gal (US)
    Pivot Shaft Oil - - 9.5 gal (US)
    Hydraulic System Tank - - 32.2 gal (US)
    Add a Similar Product: