C32 ACERT Land Mechanical Drilling Engine
Product description
Cat C32 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C32 ACERT engines to deliver excellent performance with low operating costs and emissions.This is an ideal engine for land mechanical drilling applications such as mud pump drives.Cat C32 ACERT™ Industrial Diesel Engine. Ratings: 597-1119 bkW (800-1500 bhp) @ 1800-2100 rpm meet U.S. EPA Tier 2 equivalent emission standards.
Engine Specifications
- Maximum Rating - 1500BHP
- Emissions - U.S. EPA Non-road Tier 2
- Displacement - 1953in³
- Minimum Rating - 800BHP
- Bore - 5.7in
- Stroke - 6.4in
- Rated Speed - 2100r/min
- Aspiration - Turbocharged-Aftercooled
- Governor and Protection - ADEM A3
- Engine Weight - Net Dry - 5040lb
- Rotation from Flywheel End - Counterclockwise
- Oil Change Interval - 250
- Flywheel and Flywheel Housing - SAE No. 0 or SAE No. 1
- Flywheel Teeth - 136 (SAE 0), 113 (SAE 1)
Capacity for Liquids
- Minimum Cooling System - Engine Only - 14.5gal (US)
Dimensions
- Length - 75.5in
- Width - 85in
- Height - 52in
Standard Equipment:
-
- Air Inlet System
-
- Quad turbocharger — 3 cylinder exhaust to each turbo
- Connections configured for ATAAC (Air-to-Air-Aftercooled)or remote heat exchanger
-
- Control System
-
- ADEM A4 electronic control module
- Electronic governing, PTO speed control
- Customer programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Automatic fuel temperature compensation
- Programmable low and high idle, and top engine speedlimit
- Electronic diagnostics and fault logging
- Engine monitoring system
- SAE J1939 broadcast (diagnostic and engine status)
-
- Cooling System
-
- Gear-driven centrifugal jacket water pump — RH
- Integrated thermostat and housing
- Engine oil cooler
- Optional installed transmission oil cooler
-
- Exhaust System
-
- Exhaust manifold — dry
- Two vertical exhaust outlets (front and rear)
-
- Fuel System
-
- MEUI
- Fuel priming pump
- Fuel transfer pump
- Primary and secondary fuel filter — RH configured forremote mounting (installed RH on shipping plate)
-
- Flywheels And Flywheel Housing
-
- SAE No. 0 or SAE No. 1 flywheel iron housing
- SAE No. 0 or SAE No. 1 flywheel
- Optional transmission adapter
-
- Lube System
-
- Crankcase breather
- Oil filter — RH standard, optional LH or remote mountservice
- Oil level gauge — RH standard, optional LH or dualservice
- Oil filler — RH standard, optional LH or dual service
- Shallow oil pan, rear sump
-
- Mounting System
-
- Trunnion front support
- Vertical and horizontal pads on rear flywheel housing
-
- Protection System
-
- 24V electronic
- Engine overspeed with optional air shut-offs withindicators
- Low engine oil pressure
- Fuel filter restriction
- Fuel temperature
- High engine coolant temperature
- Low engine coolant temperature
-
- General
-
- Vibration damper and optional guard
- Lifting eyes
- Optional customer wiring connector
- Service tool connector
- Paint — Cat yellow
Optional Equipment:
-
- Air Inlet System
-
- Air cleaner
- Air inlet adapters
- Turbocharger outlet adapters
- Air lines
-
- Charging System
-
- Battery chargers
- Charging alternators
- Alternator mounting
- Circuit breakers and mountings
-
- Cooling System
-
- Dry charge coolant conditioners
- Thermostat housing
- Coolant level sensor
- Radiator
- Blower fans
- Suction fans
- Fan adapters
- Fan drives
-
- Emissions
-
- IMO certifications
-
- Exhaust System
-
- Elbows
- Mufflers
-
- Fuel Systems
-
- Electric fuel priming pump
-
- Instrumentation
-
- Customer management device
- Interconnect harness
- Gauges and instrument panels
-
- Lube System
-
- Oil pans
- Oil service side
- Oil level gauge
- Oil filters
- Lubricating oils
-
- Mounting System
-
- Structural steel base
- Engine support — front
- Engine support — rear
-
- Power Take-offs
-
- Auxiliary drive
- Damper pulley
- Hydraulics gear pumps
-
- Protection System
-
- Mechanical shutoffs
- Solenoid shutoffs
-
- Starting System
-
- Electric starting motors – 12V, 24V
- Battery sets – 24V
- Battery cable
- Battery rack
- Starting aids
-
- Transmission Arrangement
-
- Transmissions water lines
- Transmissions cooler
