Compare Equipment Go Back
740 EJ Articulated Truck |
730 Bare Chassis Articulated Truck |
|
|
Engine |
|||
---|---|---|---|
Engine Model | Cat® C18 | Cat® C13 | - |
Bore | 5.7 in | 5.1 in | - |
Stroke | 7.2 in | 6.2 in | - |
Displacement | 1106 in³ | 762.8 in³ | - |
Engine Model - U.S. EPA Tier 4 Final, EU Stage V, Japan 2014 (Tier 4 Final), Korea Tier 4 Final | Cat C18 | - | - |
Gross Power - SAE J1995 | 511 HP | 375 HP | - |
Net Power - ISO 14396 | 504 HP | 370 HP | - |
Peak Engine Torque Net (SAE J1349) | 1887 ft·lbf | 1554 ft·lbf | - |
No Engine De-rating Required Below | 10000 ft | 12500 ft | - |
Note (4) | DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. ISO 22241-1 requirements are met by many brands of DEF, including those that carry the AdBlue or API certificatio | - | - |
Peak Engine Torque Gross (SAE J1995) | 1931 ft·lbf | 1579 lb/ft | - |
Note (1) | The power ratings apply at rated speed of 1,700 rpm when tested under the conditions for the specified standard. | - | - |
Peak Engine Torque Speed | 1200 r/min | 1200 r/min | - |
Note (2) | The net power advertised is the power available at the flywheel when the engine is equipped with alternator, air cleaner, muffler and fan at minimum speed. | - | - |
Note (3) | Net power when the fan is at maximum speed is 348 kW (467 hp) per the SAE reference conditions. | - | - |
Emissions | The 740 EJ meets Tier 4 Final and Stage V emission standards. | - | - |
Net Power - SAE J1349 | 496 HP | 367 HP | - |
Engine Model - U.S. EPA Tier 4 Final/EU Stage IV | - | Cat® C13 | - |
Weights |
|||
Rated Payload | 42 ton (US) | 38.9 ton (US) | - |
Body Capacities |
|||
Heaped (SAE 2:1) | 30.1 yd³ | - | - |
Struck | 23.5 yd³ | - | - |
Transmission |
|||
Forward - 1 | 3.8 mile/h | 5 mile/h | - |
Forward - 2 | 5 mile/h | 9 mile/h | - |
Forward - 3 | 7 mile/h | 14 mile/h | - |
Forward - 4 | 8.8 mile/h | 21 mile/h | - |
Forward - 5 | 11.6 mile/h | 29 mile/h | - |
Forward - 6 | 14.2 mile/h | 34 mile/h | - |
Forward - 7 | 19.6 mile/h | - | - |
Forward - 8 | 23.5 mile/h | - | - |
Reverse - 1 | 4 mile/h | 6 mile/h | - |
Reverse - 2 | 9.1 mile/h | - | - |
Forward - 9 | 34 mile/h | - | - |
Service Refill Capacities |
|||
Fuel Tank | 145.3 gal (US) | 108.8 gal (US) | - |
Cooling System | 23.7 gal (US) | 21.9 gal (US) | - |
Engine Crankcase | 13.7 gal (US) | 10 gal (US) | - |
Steering/Hoist Hydraulic System | 36.9 gal (US) | - | - |
Transmission - OTG | 19.8 gal (US) | - | - |
DEF Tank | 5.3 gal (US) | 5.3 gal (US) | - |
Axles - Each | 15.8 gal (US) | - | - |
Final Drive - Each | 1.3 gal (US) | - | - |
Brake Cooling Tank | 17.7 gal (US) | - | - |
Hydraulic System | - | 29.1 gal (US) | - |
Transmission | - | 12.4 gal (US) | - |
Final Drives/Differential | - | 33 gal (US) | - |
Output Transfer Gear Box | - | 6.3 gal (US) | - |
Sound Levels |
|||
Interior Cab | 72 dB(A) | 72 dB(A) | - |
Note (1) | The operator sound exposure Leq (equivalent sound pressure level) measured according to the work cycle procedures specified in ANSI/SAE J1166 OCT98 is 76 dB(A), for the cab offered by Caterpillar, when properly installed and maintained and tested with the | - | - |
Note (2) | Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in noisy environments. | - | - |
Standards |
|||
Brakes | ISO 3450 – 2011 | ISO 3450:2011 | - |
Cab - FOPS | ISO 3449 Level II – 2005 | ISO 3449:2005 Level II | - |
Cab - ROPS | ISO 3471 – 2008 | ISO 3471:2008 | - |
Steering | ISO 5010 – 2007 | ISO 5010:2019 | - |
Operating Weights |
|||
Front Axle - Empty | 44849 lb | - | - |
Front Axle - Loaded | 48548 lb | - | - |
Center Axle - Loaded | 57214 lb | - | - |
Center Axle - Empty | 17095 lb | - | - |
Total - Empty | 78623 lb | - | - |
Rear Axle - Rated Load | 40120 lb | - | - |
Rear Axle - Empty | 16515 lb | - | - |
Front Axle - Rated Load | 3534 lb | - | - |
Center Axle - Rated Load | 40120 lb | - | - |
Total - Loaded | 162399 lb | - | - |
Total - Rated Load | 83776 lb | - | - |
Rear Axle - Loaded | 56637 lb | - | - |
Body Plate |
|||
Type | High Strength Brinell HB450 Wear Resistant Steel | - | - |
Chute | 0.55 in | - | - |
Front | 0.28 in | - | - |
Side | 0.43 in | - | - |
Base | 0.55 in | - | - |
Steering |
|||
Lock to Lock | 4.8 seconds @ 60 rpm | 4.75 seconds @ 60 rpm | - |
Turning Circle |
|||
Note | Dimensions are for machines equipped with 29.5R25 tires. | Dimensions are for machines equipped with 23.5 R25 tires. | - |
Turning Dimensions - Aisle Width | 233 in | 210 in | - |
Turning Dimensions - Inside Radius | 173 in | 153 in | - |
Turning Dimensions - Clearance Radius | 356 in | 318 in | - |
Turning Dimensions - SAE Turning Radius | 339 in | 294 in | - |
Turning Dimensions - Steer Angle - Left/Right | 45 deg | 45 ° | - |
Blade Eject/Retract |
|||
Retract (manual) | 21 s | - | - |
Eject (manual) | 17 s | - | - |
Eject (automatic) | 16 s | - | - |
Retract (automatic) | 21 s | - | - |
Optimal Loader/Truck Pass Matching |
|||
Note | An optimum system match gives you a major productivity advantage. Having matched loading and hauling tools results in increased production and lower system costs per unit of volume moved. | - | - |
Wheel Loader: 972 - Passes | 4–5 | - | - |
Wheel Loader: 982 - Passes | 4 | - | - |
Hydraulic Excavator: 374 - Passes | 5 | - | - |
Hydraulic Excavator: 390 - Passes | 4 | - | - |
Wheel Loader: 980 - Passes | 4–5 | - | - |
Wheel Base Length |
|||
Standard Wheel Base | - | 156.7 in | - |
Long Wheel Base | - | 215.2 in | - |
Add a Similar Product:
- 745 Articulated Truck Add
- 740 GC Articulated Truck Add
- 730 EJ Articulated Truck Add
- 735 Articulated Truck Add
- 730 Articulated Truck Add
- 745 Bare Chassis Articulated Truck Add
- 725 Articulated Truck Add
- 740 GC Bare Chassis Articulated Truck Add
- 735 Bare Chassis Articulated Truck Add
- 725 Bare Chassis Articulated Truck Add