Compare Equipment Go Back
|
775 Off-Highway Truck |
|
|
Operating Specifications |
|||
---|---|---|---|
Nominal Payload Class (100%) | - | 70.5 ton (US) | - |
Top Speed - Loaded | - | 41.6 mile/h | - |
Maximum Working Payload (110%) | - | 77.5 ton (US) | - |
Target Payload (100%) | - | 70.5 ton (US) | - |
Maximum Allowable Payload (120%)* | - | 84.6 ton (US) | - |
Note (2) | - | * Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations. | - |
Note (1) | - | Capacity with Dual Slope body – no liner. | - |
Body Capacity - SAE 2:1 | - | 55.23 yd³ | - |
Engine |
|||
Engine Model | - | Cat® C27 | - |
Rated Engine Speed | - | 1800 r/min | - |
Gross Power - SAE J1995 | - | 825 HP | - |
Net Power - SAE J1349 | - | 768 HP | - |
Net Power - 80/1269/EEC | - | 775 HP | - |
Net Power - ISO 9249 | - | 775 HP | - |
Bore | - | 5.4 in | - |
Stroke | - | 6 in | - |
Displacement | - | 1648 in³ | - |
Engine Power - ISO 14396 | - | 812 HP | - |
Note (2) | - | Ratings based on SAE J1995 standard air conditions of 25° C (77° F) and 100 kPa (29.61 Hg) barometer. Power based on fuel having API gravity of 35 at 16° C (60° F) and an LHV of 42 780 kJ/kg (18,390 BTU/lb) when engine used at 30° C (86° F). | - |
Net Torque | - | 3148 ft-lb | - |
Peak Torque - Speed | - | 1200 r/min | - |
Note (1) | - | Power rating applies at 2,000 rpm when tested under the specified condition for the specified standard. | - |
Note (3) | - | No engine derating required up to 3810 m (12,500 ft) for Tier 2 Equivalent. | - |
Emissions | - | Meets EU Stage V emission standards. | - |
Capacity - Dual Slope - 100% Fill Factor |
|||
Struck | - | 42.7 yd³ | - |
Heaped (SAE 2:1)* | - | 55.5 yd³ | - |
Note (1) | - | Contact your local Cat dealer for body recommendation. | - |
Note (2) | - | *ISO 6483:1980 | - |
Capacity - Flat Floor - 100% Fill Factor |
|||
Struck | - | 42.2 yd³ | - |
Heaped (SAE 2:1)* | - | 55.2 yd³ | - |
Note (1) | - | Contact your local Cat dealer for body recommendation. | - |
Note (2) | - | *ISO 6483:1980 | - |
Weight Distributions - Approximate |
|||
Front Axle - Empty | - | 50 % | - |
Front Axle - Loaded | - | 34 % | - |
Rear Axle - Empty | - | 50 % | - |
Rear Axle - Loaded | - | 66 % | - |
Transmission |
|||
Forward - 1 | - | 6.6 mile/h | - |
Forward - 2 | - | 9.3 mile/h | - |
Forward - 3 | - | 12.6 mile/h | - |
Forward - 4 | - | 16.8 mile/h | - |
Forward - 5 | - | 22.8 mile/h | - |
Forward - 6 | - | 30.7 mile/h | - |
Forward - 7 | - | 41.6 mile/h | - |
Reverse | - | 8.7 mile/h | - |
Note | - | Maximum travel speeds with standard 24.00R35 (E4) tires. | - |
Final Drives |
|||
Differential Ratio | - | 3.64:1 | - |
Planetary Ratio | - | 4.80:1 | - |
Total Reduction Ratio | - | 17.49:1 | - |
Brakes |
|||
Brake Surface - Front | - | 257 in² | - |
Brake Surface - Rear | - | 9497 in² | - |
Brake Standards | - | ISO 3450:2011 | - |
Service Refill Capacities |
|||
Fuel Tank | - | 210 gal (US) | - |
Cooling System | - | 45 gal (US) | - |
Differential - Final Drives | - | 38 gal (US) | - |
Steering Tank | - | 9.5 gal (US) | - |
Steering System - Including Tank | - | 14 gal (US) | - |
Brake Hoist System | - | 85 gal (US) | - |
Torque Converter - Transmission System - LRC | - | 16 gal (US) | - |
Crankcase | - | 24 gal (US) | - |
Brake/Hoist Hydraulic Tank | - | 46.5 gal (US) | - |
Torque Converter - Transmission System - HRC | - | 18 gal (US) | - |
Body Hoists |
|||
Pump Flow - High Idle | - | 118 gal/min | - |
Relief Valve Setting - Raise | - | 2502 psi | - |
Relief Valve Setting - Lower | - | 500 psi | - |
Body Raise Time - High Idle | - | 10 s | - |
Body Lower Time - Float | - | 14 s | - |
Body Power Down - High Idle | - | 14 s | - |
Weights - Approximate |
|||
Maximum Gross Vehicle Weight | - | 246503 lb | - |
Suspension |
|||
Empty Loaded Cylinder Stroke Front | - | 9.2 in | - |
Rear axle - Oscillation | - | 8.1° | - |
Empty Loaded Cylinder Stroke Rear | - | 5.8 in | - |
Tires |
|||
Note (2) | - | Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection. | - |
Note (1) | - | Productive capabilities of the 775G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production. | - |
Standard Tire | - | 24.00R35 (E4) | - |
ROPS |
|||
FOPS Standards | - | Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria. | - |
ROPS Standards | - | Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria. | - |
Sound |
|||
Sound Standards (1) | - | The operator Equivalent Sound Pressure Level (Leq) is 76 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with t | - |
Sound Standards (2) | - | The exterior sound pressure level for the standard machine measured at a distance of 15 m (49 ft) according to the test procedures specified in SAE J88:2008, mid‑gear moving operation is 86 dB(A). | - |
Sound Standards (3) | - | Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in a noisy environment. | - |
Steering |
|||
Turning Diameter - Front | - | 77.1 ft | - |
Steering Standards | - | ISO 5010:2007 | - |
Steer Angle | - | 31 ° | - |
Turning Circle - Clearance Diameter | - | 85.6 ft | - |
Sustainability |
|||
Recyclability | - | 98% | - |
Add a Similar Product:
There are no similar products.