Compare Equipment Go Back
 EMCP 4.4 Master Control Panel |
 MX350 Controller |
|
|
Technical Summary |
|||
|---|---|---|---|
| Configuration | Remote monitoring and control for up to 8 generator sets via high-speed network. Enables paralleling a group of EMCP 4.4 equipped generator sets to a single utility source. | - | - |
| Modes of Operation | Emergency standby, island, utility paralleling | - | - |
| Application | LV and MV (208V - 38 kV) | - | - |
| Rating Range | - | Switch Dependent | - |
| Transfer Type | - | Application Dependent | - |
| Switch Type | - | Application Dependent | - |
Generator Protective Devices |
|||
| ANSI Protective Devices | 15/25, 27/59, 81 O/U, 32, 40, 50, 51 | - | - |
Utility Protective Devices |
|||
| ANSI Protective Devices | 15/25. 27/59, 81 O/U, 32,47 (Industrial Grade) | - | - |
Environmental Parameters |
|||
| Certifications | IBC, CBC, UBC & OSHPD Certified | - | - |
| Control Panel Enclosure | NEMA 1 wall-mounted construction | - | - |
| Operating Temperature | 0°C to 50°C | - | - |
| Storage Temperature | -20°C to +60°C | - | - |
| Low Voltage Standards | NEMA SG-5, CSA, ANSI C37.51, ANSI C37.20.1, UL 1558 or UL 891, NFPA 110, NFPA 99 and NFPA 70 | - | - |
| Medium Voltage Standards | NEMA SG-5, ANSI / IEEE C37.20.2, CSA-C22.2 No. 31-M89, EEMAC G8-3.2, NFPA 70, NFPA 99 and NFPA 1110 | - | - |
Controller Specifications |
|||
| Voltage Unbalance on Dropout for Source 1 and Source 2 | - | 5 to 20% of nominal | - |
| Delay NeutralTransition Time Delays (DT,DW) | - | 0-10 minutes | - |
| Control Power | - | 120 VAC | - |
| Undervoltage Dropout for Source 1 and Source 2 | - | 75-99% of nominal | - |
| Undervoltage Restore for Source 1 and Source 2 | - | 85-100% of nominal | - |
| Overfrequency Dropout for Source 1 and Source 2 | - | 50.1 - 63 Hz | - |
| Source Sensing | - | 120 - 690 VAC +/- 1% of nominal voltage (+/- .05 Hz, +/-.5 A) | - |
| Delay for Engine Cool Down (U) | - | 0-60 minutes | - |
| Underfrequency Restore for Source 1 and Source 2 | - | 45 - 59.5 Hz | - |
| Load Control Relay Contacts (2) | - | 0-259 minutes | - |
| Overvoltage Dropout for Source 1 and Source 2 | - | 105 - 110% of nominal | - |
| Voltage Unbalance for Restore for Source 1 and Source 2 | - | 4 to 19% of nominal | - |
| Storage Temperature | - | (-40˚C - 90˚C ) | - |
| Underfrequency Dropout for Source 1 and Source 2 | - | 45 - 59.9 Hz | - |
| Overfrequency Restore for Source 1 and Source 2 | - | 50 - 62.9 Hz | - |
| Delay Transfer to Nonpreferred Source (W) | - | 0-5 minutes | - |
| Operating Temperature Ambient | - | (-20˚C to 50˚C) | - |
| Communications Interface - Optional | - | Serial RS-485 upt to 115.2 Kbps or TCP/IP (10/100 base-T) | - |
| Overvoltage Restore for Source 1 and Source 2 | - | 103 - 108% of nominal | - |
| Load Control Relay Contacts (1) | - | rated for 10A @ 24VDC or 120VAC | - |
Add a Similar Product:
-
MX250 Microprocessor Controller Add
-
CTSM and CTGM Series Manual Transfer Switches Add
-
CTX Series Automatic Transfer Switch Add
-
MX150 Microprocessor Controller Add
-
-
CTS Series Automatic Transfer Switch Add
-
CTE Series Automatic Transfer Switch Add
-
-
Cat XLM Switchgear Add
-
Cat Customizable Switchgear and Controls Add