Compare

Compare Equipment Go Back

Engine
	966 View Product	992 Wheel Loader View Product Remove	995 Wheel Loader View Product Remove	988 Wheel Loader View Product Remove
Engine Power @ 1,600 rpm - ISO 14396:2002	321 HP	-	-	-
Gross Power @ 1,600 rpm - SAE J1995:2014	325 HP	-	-	-
Engine Model	Cat C9.3B	Cat® C32B	Cat® 3516E	Cat® C18 ™
Net Power @ 1,600 rpm - ISO 9249:2007, SAE J1349:2011	303 HP	-	-	-
Note (1)	Cat engine meets U.S. EPA Tier 4 Final, EU Stage V, Korea Stage V, China Nonroad Stage IV and Japan 2014 emission standards.	-	The power ratings apply when tested under the reference conditions for the specified standard.	-
Note (2)	The net power advertised is the power available at the flywheel when the engine is equipped with fan, alternator, air cleaner, and aftertreatment.	-	The net power advertised is the power available at the flywheel when the engine is equipped with fan, alternator, air cleaner and muffler.	-
Net Torque @ 1,200 rpm - ISO 9249:2007, SAE J1349:2011	1255 ft-lb	-	-	-
Engine Torque @ 1,200 rpm – ISO 14396:2002	1313 lb/ft	-	-	-
Gross Torque @ 1,200 rpm – SAE J1995:2014	1327 lb/ft	-	-	-
Note (3)	Cat diesel engines are required to use ULSD (ultra-low sulfur diesel fuel with 15 ppm of sulfur or less) or ULSD blended with the following lower-carbon intensity fuels up to: • 20% biodiesel FAME (fatty acid methyl ester)* • 100% renewable diesel, HVO (h	-	The gross power advertised is with the fan at maximum speed.	-
Displacement	9.3 L	1963.5 in³	4766 in³	1105 in³
Net Power	-	814 HP	-	-
Emissions	-	U.S. EPA Tier 4 Final, U.S. EPA Tier 2 Equivalent	U.S. EPA Tier 4 Final/EU Stage V or U.S. EPA Tier 1 equivalent	U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 emission standards, Brazil MAR-1 and China Nonroad Stage IV emission standards, equivalent to U.S. EPA Tier 3 and EU Stage IIIA, and U.S. EPA Tier 2 and EU Stage II
Rated Speed	-	1750 rpm	-	1700/min
Gross Power - SAE J1995 at 1,750 rpm - Tier 4/HRC (Highly Regulated Country) - Standard	-	900 HP	-	-
Gross Power - SAE J1995 at 1,750 rpm - Tier 4/HRC - High Ambient	-	937 HP	-	-
Gross Power - SAE J1995 at 1,750 rpm - Tier 2/LRC (Less Regulated Country) - Standard	-	907 HP	-	-
Gross Power - SAE J1995 at 1,750 rpm - Tier 2/LRC - High Ambient	-	944 HP	-	-
Gross Power - ISO 14396 at 1,750 rpm - Tier 4/HRC - Standard	-	884 HP	-	-
Gross Power - ISO 14396 at 1,750 rpm - Tier 4/HRC - High Ambient	-	921 HP	-	-
Gross Power - ISO 14396 at 1,750 rpm - Tier 2/LRC - Standard	-	893 HP	-	-
Gross Power - ISO 14396 at 1,750 rpm - Tier 2/LRC - High Ambient	-	931 HP	-	-
Net Power - SAE J1349 at 1,750 rpm - Tier 4/HRC - Standard	-	814 HP	-	-
Net Power - SAE J1349 at 1,750 rpm - Tier 4/HRC - High Ambient	-	814 HP	-	-
Net Power - SAE J1349 at 1,750 rpm - Tier 2/LRC - Standard	-	823 HP	-	-
Net Power - SAE J1349 at 1,750 rpm - Tier 2/LRC - High Ambient	-	823 HP	-	-
Bore	-	5.7 in	6.7 in	5.7 in
Stroke	-	6.4 in	8.5 in	7.2 in
Peak Torque - SAE J1995 - Tier 4/HRC - Standard @ 1,200 rpm	-	3514 ft·lbf	-	-
Peak Torque - SAE J1995 - Tier 4/HRC - High Ambient @ 1,300 rpm	-	3555 ft·lbf	-	-
Peak Torque - SAE J1995 - Tier 2/LRC - Standard @ 1,200 rpm	-	3537 ft·lbf	-	-
Peak Torque - SAE J1995 - Tier 2/LRC - High Ambient @ 1,350 rpm	-	3570 ft·lbf	-	-
Engine Power - ISO 14396	-	-	1847 HP	-
Gross Power - SAE J1995	-	-	1870 HP	-
Net Power - SAE J1349 - Standard Ambient	-	-	1739 HP	-
Net Power - SAE J1349 - High Ambient	-	-	1696 HP	-
Peak Torque - 1,200 rpm - SAE J1995	-	-	8549 lb/ft	-
Torque Rise	-	-	39%	58 %
Net Power - SAE J1349:2011	-	-	-	538 HP
Engine Power - ISO 14396:2002	-	-	-	580 HP
Gross Power - SAE J1995:2014	-	-	-	588 HP
Peak Power Speed	-	-	-	1500/rpm
Peak Torque - 1,200 rpm	-	-	-	2230 lb/ft
Weights
Operating Weight	51124 lb	-	-	-
Note	Weight based on a machine configuration with Bridgestone 29.5R25 VSNT L4 radial tires, full fluids, operator, standard counterweight, ride control cold start, roading fenders, Product Link, open differential axles (front/rear), secondary steering, sound s	-	-	-
Bucket Capacities
Bucket Range	2.8-11.9 m³ 3.75-15.5 yd³	-	-	-
Transmission
Forward - 1	4.2 mile/h	4.3 mile/h	4.6 mile/h	4 mile/h
Forward - 2	8.4 mile/h	7.4 mile/h	8 mile/h	7.2 mile/h
Forward - 3	15 mile/h	12.7 mile/h	13.6 mile/h	12.7 mile/h
Forward - 4	24.5 mile/h	-	-	21.6 mile/h
Note	Maximum travel speed in standard vehicle with empty bucket and standard L3 tires with 849 mm (33 in) roll radius.	-	Travel speeds based on 58/85-57 tires.	-
Reverse - 1	4.5 mile/h	4.7 mile/h	5 mile/h	4.7 mile/h
Reverse - 2	9.2 mile/h	8.1 mile/h	8.8 mile/h	8.3 mile/h
Reverse - 3	16.5 mile/h	13.9 mile/h	14.9 mile/h	14.4 mile/h
Reverse - 4	24.5 mile/h	-	-	-
Transmission Type	-	Cat Planetary Powershift	Cat Planetary Power Shift	Cat planetary powershift
Direct Drive - Forward 1	-	Disabled	Lock-up disables	Lock-up disabled
Direct Drive - Forward 2	-	8 mile/h	8.7 mile/h	7.8 mile/h
Direct Drive - Forward 3	-	14 mile/h	15.2 mile/h	13.9 mile/h
Direct Drive - Reverse 1	-	5 mile/h	Lock-up disables	5 mile/h
Direct Drive - Reverse 2	-	8.8 mile/h	9.6 mile/h	8.9 mile/h
Direct Drive - Reverse 3	-	15.3 mile/h	16.8 mile/h	15.8 mile/h
Direct Drive - Forward 4	-	-	-	24.4 mile/h
Sound
Note (1)	** For machines in European Union countries and in countries that adopt the EU Directives.	-	-	-
Note (2)	***European Union Directive 2000/14/EC as amended by 2005/88/EC.	-	-	-
With Cooling Fan Speed at 70% of Maximum Value - Exterior Sound Power Level*	108	-	-	-
With Cooling Fan Speed at 70% of Maximum Value - Operator Sound Pressure Level (ISO 6396:2008)	69 dB(A)	-	-	-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Power Level (ISO 6395:2008)	109 dB(A)	-	-	-
With Cooling Fan Speed at Maximum Speed - Exterior Sound Pressure Level (SAE J88:2013)	76	-	-	-
With Cooling Fan Speed at Maximum Speed - Operator Sound Pressure Level (ISO 6396:2008)	70 dB(A)	-	-	-
With Cooling Fan Speed at Maximum Value - Note	Distance of 15 m (49.2 ft), moving forward in second gear ratio.	-	-	-
Air Conditioning System
Air Conditioning	The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.6 kg (3.5 lb) of refrigerant which has a CO2 equivalent 2.288 metric tonnes (2.522 tons).	-	-	The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.
Operating Specifications
Breakout Force	38999 lb	-	-	-
Note (1)	For a machine configuration as defined under Weight.	-	-	-
Note (2)	Full compliance to ISO 14397-1:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing.	-	-	-
Static Tipping Load - Full 40° Turn - No Tire Deflection	15981 kg	-	-	-
Static Tipping Load - Full 40° Turn - With Tire Deflection	32727 lb	-	-	-
Operating Weight	-	233430 lb	-	112574 lb
Rated Payload - Standard	-	25.5 ton (US)	-	-
Rated Payload - Standard (Material Handler)	-	30 ton (US)	-	-
Rated Payload - High Lift	-	22.5 ton (US)	-	-
Rated Payload - High Lift (Material Handler)	-	27 ton (US)	-	-
Bucket Capacity Range	-	11.5-24.5 m³ (15-32 yd³)	17.2-43.6 m3 (22.3-57 yd3)	4.7-13 m3 (6.2-17 yd3)
Cat Truck Match - Standard	-	775/777	785/789	770～772
Cat Truck Match - High Lift	-	785	789/793/794	773～775
Operating Weight - Standard	-	-	543772 lb	-
Operating Weight - High Lift	-	-	547675 lb	-
Rated Payload - Standard Lift (Low to Moderate Digging Resistance)	-	-	60 ton (US)	-
Rated Payload - Standard Lift (Moderate to High Digging Resistance)	-	-	50 ton (US)	-
Rated Payload - High Lift (Low to Moderate Digging Resistance)	-	-	55 ton (US)	-
Rated Payload - High Lift (Moderate to High Digging Resistance)	-	-	50 ton (US)	-
Note	-	-	*Please contact your local dealer to determine if your application is suitable for this increased rated payload.	-
Rated Payload - Quarry Face	-	-	-	12.5 t
Rated Payload - Loose Material	-	-	-	16 t
Service Refill Capacities
Cooling System	17.4 gal (US)	-	-	31.7 gal (US)
Crankcase	6.1 gal (US)	31.7 gal (US)	-	15.9 gal (US)
DEF Tank	6.9 gal (US)	-	-	-
Differential - Final Drives - Front	15.1 gal (US)	96.4 gal (US)	-	49.1 gal (US)
Differential - Final Drives - Rear	15.1 gal (US)	96.4 gal (US)	-	49.1 gal (US)
Fuel Tank	80.1 gal (US)	385.7 gal (US)	-	188 gal (US)
Hydraulic Tank	30.1 gal (US)	-	-	-
Transmission	15.5 gal (US)	51.5 gal (US)	-	31.7 gal (US)
Cooling Systems	-	59.4 gal (US)	-	-
Hydraulic System Factory Fill (Implement)	-	104.1 gal (US)	-	-
Hydraulic Tank - Implement	-	60.2 gal (US)	-	-
Hydraulic Factory Fill (Steering)	-	32.5 gal (US)	-	-
Hydraulic Tank (Steering Tank Only)	-	26.3 gal (US)	-	-
Coolant (Validated by Test Cell Fill Quantities)	-	-	-	33 gal (US)
Diesel Exhaust Fluid Tank	-	-	-	8.7 gal (US)
Transmission - Validated by Test Cell Fill Quantities	-	-	-	29 gal (US)
Hydraulic System Factory Fill	-	-	-	125.5 gal (US)
Hydraulic System - Tank Only	-	-	-	63.4 gal (US)
Hydraulic System
Implement System - Maximum Operating Pressure	4496 psi	-	-	-
Implement System - Maximum Pump Output at 2,250 rpm	99 gal/min	-	-	-
Hydraulic Cycle Time - Total	10.1 seconds	-	-	-
Dimensions
Note	All dimensions are approximate and based on machine equipped with 5.4 m3 (7.1 yd3) general purpose bucket with BOCE and Bridgestone 29.5R25 VSNT L4 radial tires.	-	-	-
Dimensions - High Lift
Centerline of Rear Axle to Edge of Counterweight	8.1 ft	-	-	-
Centerline of Rear Axle to Hitch	5.1 ft	-	-	-
Ground Clearance	1.4 ft	-	-	-
Height - Top of Exhaust Pipe	11.8 ft	-	-	-
Height - Top of Hood	9.5 ft	-	-	-
Height - Top of ROPS	11.1 ft	-	-	-
Hinge Pin Height at Carry	2.6 ft	-	-	-
Hinge Pin Height at Maximum Lift	15.9 ft	-	-	-
Lift Arm Clearance at Maximum Lift	13.8 ft	-	-	-
Overall Length - Without Bucket	26.6 ft	-	-	-
Tread Width	7.3 ft	-	-	-
Wheel Base	11.8 ft	-	-	-
Rack Back - Carry Height	49 degrees	-	-	-
Rack Back - Maximum Lift	71 degrees	-	-	-
Width over Tires (Loaded)	9.11 ft	-	-	-
Rack Back at Ground	37 degrees	-	-	-
Dimensions - Standard Lift
Centerline of Rear Axle to Edge of Counterweight	7.7 ft	-	-	-
Centerline of Rear Axle to Hitch	5.1 ft	-	-	-
Ground Clearance	424 mm	-	-	-
Height - Top of Exhaust Pipe	3531 mm	-	-	-
Height - Top of Hood	2850 mm	-	-	-
Height - Top of ROPS	3593 mm	-	-	-
Hinge Pin Height at Carry	2 ft	-	-	-
Hinge Pin Height at Maximum Lift	4245 mm	-	-	-
Lift Arm Clearance at Maximum Lift	3687 mm	-	-	-
Overall Length - Without Bucket	7399 mm	-	-	-
Tread Width	7.3 ft	-	-	-
Wheel Base	3550 mm	-	-	-
Rack Back - Carry Height	50 degrees	-	-	-
Width over Tires (Loaded)	9.11 ft	-	-	-
Rack Back - Maximum Lift	62 degrees	-	-	-
Rack Back at Ground	39 degrees	-	-	-
Buckets
Bucket Capacities	-	11.5-24.5 m³ (15-32 yd³)	-	4.7-13 m3 (6.2-17 yd3)
Hydraulic System - Lift/Tilt
Lift/Tilt System - Circuit	-	Positive Flow Control	Positive Flow Control	EH- Positive Flow Control, Flow Sharing
Lift/Tilt System - Pump	-	Variable Displacement Piston	Variable Displacement Piston	-
Maximum Flow at 2,165 rpm	-	250 gal/min	-	-
Relief Valve Setting - Lift/Tilt	-	5000 psi	5004 psi	4757 psi
Lift Cylinder - Bore	-	9.3 in	-	-
Lift Cylinder - Stroke	-	63.5 in	-	-
Tilt Cylinder - Bore	-	11.5 in	-	-
Tilt Cylinder - Stroke	-	41.5 in	-	-
Maximum Flow at 1,700 rpm Engine Speed	-	-	541 gal/min	-
Cylinders, Double Acting - Lift, Bore and Stroke	-	-	370 × 1713 mm (14.6 × 67.4 in)	210 mm × 1050 mm (8.7 in × 41.3 in)
Cylinders, Double Acting - Tilt, Bore and Stroke	-	-	310 × 1086 mm (12.2 × 42.8 in)	269 mm × 685 mm (8.7 in × 27 in)
Pilot System	-	-	Open Loop and Pressure Reducing	Variable displacement piston
Lift/Tilt System	-	-	-	Variable displacement piston
Maximum Flow at 1,400-1,860 rpm	-	-	-	153 gal/min
Relief Valve Setting - Main	-	-	-	551 psi
Hydraulic Cycle Times
Rack Back	-	2.3 s	4.9 s	-
Rack Back - High Lift	-	2.3 s	-	-
Raise	-	9 s	12.6 s	-
Raise - High Lift	-	9 s	-	-
Dump	-	2.6 s	3.1 s	-
Dump - High Lift	-	2.6 s	-	-
Float Down	-	3.2 s	-	-
Float Down - High Lift	-	3.2 s	-	-
Total Hydraulic Cycle Time	-	17.1 s	-	-
Lower Float Down	-	-	4.2 s	-
Axles
Front	-	Fixed	Fixed	Fixed
Rear	-	Trunnion	Trunnion	Trunnion
Oscillation Angle	-	±9°	9°	13 °
Brakes
Brakes	-	ISO 3450:2011	ISO 3450:2011	ISO 3450:2011
Hydraulic System - Steering
Steering System - Circuit	-	Pilot, Load Sensing	Pilot, Load Sensing	Pilot, load sensing
Steering System - Pump	-	Piston, Variable Displacement	Piston, Variable Displacement	Piston, variable displacement
Maximum Flow at 1,400-1,850 rpm	-	70 gal/min	-	-
Steering Cut Off Pressure	-	4500 psi	-	-
Total Steering Angle	-	80°	80 degrees	86 °
Steering Cycle Times - Low Idle	-	4.9 s	7.6 s	5.6 s
Steering Cycle Times - High Idle	-	3.1 s	4.3 s	3.4 s
Maximum Flow	-	-	-	71.3 gal/min
Relief Valve Setting - Steering	-	-	-	4351 psi
Cooling System
Ambient Capability Hydraulically Driven Demand Fan - Standard	-	109.4 °F	109.4 °F	-
Ambient Capability, Hydraulically Driven Demand Fan - High	-	131 °F	-	-
Ambient Capability Hydraulically Driven Demand Fan - High (Tier 1 equivalent)	-	-	131 °F	-
Ambient Capability Hydraulically Driven Demand Fan - High (Tier 4 Final)	-	-	127.4 °F	-
Sound Performance - Standard
Note	-	Machine Sound Level (ISO 6396:2008) - 116 dB(A)	The declared sound levels listed above include the addition of both measurement uncertainty and uncertainty due to production variation. Typical measurement uncertainty for this type of machine is 2 dBA in accordance with "ISO 4871". The measurement was c	-
Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent	-	-	74 dB(A)	-
Machine Sound Level (ISO 6395:2008)	-	-	119 dB(A)	-
Sound Performance - Suppression
Note	-	Machine Sound Level (ISO 6396:2008) - 113 dB(A)	The declared sound levels listed above include the addition of both measurement uncertainty and uncertainty due to production variation. Typical measurement uncertainty for this type of machine is 2 dBA in accordance with "ISO 4871". The measurement was c	-
Operator Sound Level (ISO 6396:2008) - Tier 1/EU Stage I Equivalent	-	-	73 dB(A)	-
Machine Sound Level (ISO 6395:2008)	-	-	117 dB(A)	-
Dimensions - Standard Lift - Approximate
Ground to Top of Exhaust Stacks	-	17 ft	23.2 ft	-
Ground to Top of ROPS	-	18.3 ft	23.4 ft	-
Ground to Top of Hood	-	13.1 ft	18.6 ft	-
Ground to Center of Front Axle	-	4.3 ft	-	-
Ground to Bumper Clearance	-	3.8 ft	4.4 ft	-
Ground to Lower Hitch Clearance	-	2.2 ft	2.9 ft	-
Reach - Maximum Lift	-	8.2 ft	9.6 ft	-
Clearance at Maximum Lift	-	15.2 ft	19.8 ft	-
B-Pin Height - Maximum Lift	-	22.8 ft	28.8 ft	-
Maximum Overall Height - Bucket Raised	-	30.8 ft	39.3 ft	-
Rear Axle - Centerline to Bumper	-	13.5 ft	20.4 ft	-
Tread Width	-	10.83 ft	14.1 ft	-
Rack Back Angle - Maximum Lift	-	56.9 degrees	-	-
Dump Angle at Maximum Lift	-	-49.5 degrees	–50.0 degrees	-
Rack Back Angle - Ground Level	-	40.2 degrees	39.7 degrees	-
Width - Over Tires - With Bulge	-	14.74 ft	18.8 ft	-
Rack Back Angle - Carry	-	48.9 degrees	47.7 degrees	-
Wheel Base	-	19.3 ft	22.3 ft	-
Maximum Overall Length	-	50.8 ft	64.6 ft	-
Front Axle Centerline to Bucket Tip	-	18 ft	21.9 ft	-
Ground to Center of Axles	-	-	6 ft	-
Note	-	-	Assumes loaded 58/85-57 tires, tires at a static loaded radius of 1830 mm (6 ft), 596-5330 26 m3 (34 yd3) bucket, 431-0064 HD tips.	-
Rack Angle at Maximum Lift	-	-	59.5 degrees	-
Dimensions - High Lift - Approximate
Tread Width	-	10.83 ft	14.1 ft	-
Rack Back Angle - Ground Level	-	42.5 degrees	45 degrees	-
Dump Angle at Maximum Lift	-	-48.1 degrees	–50.0 degrees	-
Rack Back Angle - Maximum Lift	-	56.2 degrees	-	-
Width - Over Tires - With Bulge	-	14.75 ft	18.8 ft	-
Rack Back Angle - Carry	-	51.6 degrees	53.5 degrees	-
Ground to Top of Exhaust Stacks	-	17 ft	23.2 ft	-
Ground to Top of ROPS	-	18.3 ft	23.4 ft	-
Ground to Top of Hood	-	13.1 ft	18.6 ft	-
Ground to Center of Front Axle	-	4.3 ft	-	-
Ground to Bumper Clearance	-	3.8 ft	4.4 ft	-
Ground to Lower Hitch Clearance	-	2.2 ft	2.9 ft	-
Reach - Maximum Lift	-	7.6 ft	9.4 ft	-
Clearance at Maximum Lift	-	17.2 ft	22.6 ft	-
B-Pin Height - Maximum Lift	-	24.5 ft	31.6 ft	-
Maximum Overall Height - Bucket Raised	-	32 ft	42.1 ft	-
Rear Axle - Centerline to Bumper	-	13.5 ft	20.4 ft	-
Wheel Base	-	19.3 ft	22.3 ft	-
Maximum Overall Length	-	51.6 ft	66.9 ft	-
Front Axle Centerline to Bucket Tip	-	18.8 ft	24.2 ft	-
Ground to Center of Axles	-	-	6 ft	-
Note	-	-	Assumes loaded 58/85-57 tires, tires at a static loaded radius of 1830 mm (6 ft), 596-5330 26 m3 (34 yd3) bucket, 431-0064 HD tips.	-
Rack Angle at Maximum Lift	-	-	59.4 degrees	-
Complete System Fill
Fuel Tank - Standard	-	-	856 gal (US)	-
Fuel Tank - With 24 hr Attachment	-	-	1414 gal (US)	-
Cooling System	-	-	138 gal (US)	-
Engine Crankcase	-	-	76 gal (US)	-
Transmission	-	-	110 gal (US)	-
Differential - Final Drives - Front	-	-	220 gal (US)	-
Differential - Final Drives - Rear	-	-	200 gal (US)	-
Hydraulic Tank - Implement and Hydraulic Fan	-	-	270 gal (US)	-
Hydraulic Tank - Steering and Braking	-	-	100 gal (US)	-
Oil Renewal System (ORS)*	-	-	20 gal (US)	-
Note	-	-	*Not available on Tier 4 Final/Stage V machines. Not available in all regions.	-
Hydraulic Cycle Time (1,400-1,860 rpm)
Rack Back	-	-	-	4.5 s
Raise	-	-	-	8 s
Dump	-	-	-	2.2 s
Lower Float Down	-	-	-	3.5 s
Total Hydraulic Cycle Time - Empty Bucket	-	-	-	18.2 s
Operator's Cab
ROPS/FOPS	-	-	-	ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards
Sound Performance - Tier 4 Final / Stage V - Standard
Operator Sound Pressure Level (ISO 6396:2008)	-	-	-	73 dB(A)
Machine Sound Power Level (ISO 6395:2008)	-	-	-	111 dB(A)
Sound Performance - Tier 3 / Stage III - Standard
Operator Sound Pressure Level (ISO 6396:2008)	-	-	-	73 dB(A)
Machine Sound Power Level (ISO 6395:2008)	-	-	-	112 dB(A)
Dimensions (Approximate) - Standard Lift Linkage
Ground to Top of ROPS	-	-	-	13.8 ft
Ground to Top of Exhaust Stacks	-	-	-	14.8 ft
Ground to Top of Hood	-	-	-	10.9 ft
Rear Axle - Centerline to Bumper	-	-	-	10.5 ft
Front Axle Centerline to Bucket Tip	-	-	-	14 ft
Wheel Base	-	-	-	14.9 ft
Maximum Overall Length	-	-	-	39.3 ft
Ground to Lower Hitch Clearance	-	-	-	1.9 ft
Clearance at Maximum Lift	-	-	-	11.9 ft
B-Pin Height - Maximum Lift	-	-	-	18 ft
Maximum Overall Height - Bucket Raised	-	-	-	24.5 ft
Reach - Maximum Lift	-	-	-	6.5 ft
Dimensions (Approximate) - High Lift Linkage
Ground to Top of ROPS	-	-	-	13.8 ft
Ground to Top of Exhaust Stacks	-	-	-	14.8 ft
Ground to Top of Hood	-	-	-	10.9 ft
Rear Axle - Centerline to Bumper	-	-	-	10.5 ft
Front Axle Centerline to Bucket Tip	-	-	-	15.3 ft
Wheel Base	-	-	-	14.9 ft
Maximum Overall Length	-	-	-	40.7 ft
Ground to Lower Hitch Clearance	-	-	-	1.9 ft
Clearance at Maximum Lift	-	-	-	13.3 ft
B-Pin Height - Maximum Lift	-	-	-	19.3 ft
Maximum Overall Height - Bucket Raised	-	-	-	25.8 ft
Reach - Maximum Lift	-	-	-	6.8 ft

Compare Equipment Go Back

966

992 Wheel Loader

995 Wheel Loader

988 Wheel Loader

Engine

Weights

Bucket Capacities

Transmission

Sound

Air Conditioning System

Operating Specifications

Service Refill Capacities

Hydraulic System

Dimensions

Dimensions - High Lift

Dimensions - Standard Lift

Buckets

Hydraulic System - Lift/Tilt

Hydraulic Cycle Times

Axles

Brakes

Hydraulic System - Steering

Cooling System

Sound Performance - Standard

Sound Performance - Suppression

Dimensions - Standard Lift - Approximate

Dimensions - High Lift - Approximate

Complete System Fill

Hydraulic Cycle Time (1,400-1,860 rpm)

Operator's Cab

Sound Performance - Tier 4 Final / Stage V - Standard

Sound Performance - Tier 3 / Stage III - Standard

Dimensions (Approximate) - Standard Lift Linkage

Dimensions (Approximate) - High Lift Linkage

Earthmoving

Parts & Service

Power Systems

Technology

Contact Us