Compare Equipment Go Back
 6030 Hydraulic Shovel |
 6020B Hydraulic Shovel |
 6015 Hydraulic Shovel |
|
General |
|||
|---|---|---|---|
| Engine Output - SAE J1995 | 1649 HP | 1040 HP | 824 HP |
| Bucket Payload | 33 ton (US) | 23.8 ton (US) | 16.1 ton (US) |
| Operating Weight | 324 ton (US) | 253.8 ton (US) | 154.3 ton (US) |
| Note | Specifications shown above apply to the highly regulated Face Shovel configuration. Backhoe and Frontless configurations are also available for all regions. | Specifications shown above apply to a Backhoe configuration. A frontless configuration is also available. | Specifications shown above apply to highly regulated, backhoe configuration. Lesser regulated and frontless configurations are also available. |
| Standard Bucket Capacity | - | 15.7 yd³ | - |
Diesel Engine - Highly Regulated |
|||
| Gross Power - SAE J1995 | 1649 HP | 1033 HP | - |
| Net Power - ISO 9249 | 1625 HP | 1024 HP | - |
| Net Power - SAE J1349 | 1541 HP | 1019 HP | - |
| Emissions | Meets U.S. EPA Tier 4 Final and EU Stage V emission standards | Meets Tier 4 Final and Stage V emissions standards | - |
Diesel Engine - Lesser Regulated |
|||
| Gross Power - SAE J1995 | 1531 HP | 1040 HP | - |
| Net Power - SAE J1349 | 1425 HP | 1032 HP | - |
| Net Power - ISO 9249 | 1511 HP | 1037 HP | - |
| Emissions | Meets China Nonroad Stage III emission standards, equivalent to U.S. EPA Tier 2 | Meets China Nonroad Stage III emissions standards, equivalent to Tier 2 | - |
Diesel Engines |
|||
| Number of Cylinders - Each Engine | 12 | - | - |
| Bore | 5.42 in | - | - |
| Stroke | 6 in | - | - |
| Displacement | 1648 in³ | - | - |
| Aspiration | Turbocharged and air-to-air aftercooled | - | - |
| Components (1) | Hydraulically driven radiator fan with electronically controlled fan speed | - | - |
| Components (2) | Micro processed engine management | - | - |
| Components (3) | Heavy-duty air filters | - | - |
| Components (4) | Two-stage fuel filter, including water separator | - | - |
| Components (5) | Additional high-capacity water separator | - | - |
| Emissions | Meets U.S. EPA Tier 4 Final and EU Stage V emission standards | - | - |
| Fuel Tank Capacity | 1342 gal (US) | - | - |
Electrical System - Diesel Drive |
|||
| System Voltage | 24V | - | - |
| Batteries in Series/Parallel Installation | 4 x 210 Ah at 12V each; 420 Ah with 24V in total | - | - |
| Components (1) | Battery isolation relays | - | - |
| Components (2) | Emergency stop switches accessible from ground level and in engine module | - | - |
| Components (3) | 14 LED high-brightness working flood lights | - | - |
| Components (4) | 11 LED service lights | - | - |
Electrical System |
|||
| Batteries | 4 maintenance-free batteries | - | 4 × 200 Ah (12 V each) |
| Batteries (12V each) - In Series/Parallel Installation | - | 630 Ah – 24V | - |
| Components (3) | - | 9 LED high-brightness working flood lights: – 7 for working area – 2 for rear end |
Lockable battery isolation switch |
| Batteries (12V each) | - | 6 × 210 Ah | - |
| Components (1) | - | Emergency stop buttons inside cab, accessible from all seating locations, and engine module | Emergency stop in cabin, engine module, pump room and on service station accessible from ground level |
| Components (2) | - | Additional ground-level emergency stop | Four maintenance free batteries |
| System Voltage | - | 24V | 24 V |
| Battery Isolation Relays | - | manual lockable disconnect switch and automatic disconnect relay | - |
| Components (6) | - | 1 beacon lamp on cab roof | 2 electric horns |
| Components (5) | - | 7 LED service lights | 14 LED high-brightness working lights |
| Components (4) | - | 2 LED high-brightness access flood lights | 5 LED service lights |
| Alternator Rating | - | - | 150 A (24 V) in total |
| Components (7) | - | - | Two (2) lights for rear end |
| Components (9) | - | - | One (1) beacon light on cabin roof |
| Components (8) | - | - | One (1) light for machine deck/service |
Operating Weights |
|||
| 6030 FS - Standard Track Pads | 3.25 ft | - | - |
| 6030 FS - Operating Weight | 657640 lb | - | - |
| 6030 FS - Ground Pressure | 32.2 psi | - | - |
| 6030 - Standard Track Pads | 3.25 ft | - | - |
| 6030 - Operating Weight | 660060 lb | - | - |
| 6030 - Ground Pressure | 32.3 psi | - | - |
| Note | Other track pads available on request. Operating weights include: base machine, front attachment, standard track pads, standard rock bucket, and 100% fuel and lubricants. | - | - |
Hydraulic System with Pump Managing System |
|||
| Hydraulic Tank Capacity - Approximately | 707 gal (US) | - | - |
| Total Volume of Hydraulic Oil - Approximately | 925 gal (US) | - | - |
| Main Pumps | 4 x variable swash plate pumps | - | - |
| Main Pumps - Maximum Oil Flow - Diesel Version | 4 x 552 L/min (4 x 146 gal/min) | - | - |
| Maximum Pressure - Attachment | 4495 psi | - | - |
| Maximum Pressure - Travel | 5220 psi | - | - |
| Swing Pumps | 2 x reversible swash plate double pumps | - | - |
| Swing Pumps - Maximum Oil Flow - Diesel Version | 4 x 197 L/min (4 x 52 gal/min) | - | - |
| Maximum Pressure - Swing Pumps | 5076 psi | - | - |
Hydraulic Oil Cooling |
|||
| Oil Flow of Cooling Pumps - Diesel Version | 2 x 467 L/min (2 x 123 gal/min) | - | - |
| Diameter - Fan | 48 in | 4.92 ft | - |
| Features (2) | - | Variable electronically controlled flow of oil through cooler and fan speed | - |
| Oil Flow of Cooling Pumps | - | 211 gal/min | - |
| Features (1) | - | Cooling system fully independent of all main circuits, i.e. controlled cooling capacity available whenever engine is running | - |
| Features (3) | - | Superior cooling efficiency to ensure optimum oil temperature | - |
Swing System |
|||
| Swing Drive | 2 compact planetary transmissions with axial piston motors | 2 compact planetary transmissions with axial piston motors | Two (2) compact planetary transmissions with axial piston motors |
| Parking Brakes | Wet multiple-disc brake, spring-loaded/hydraulically released | - | - |
| Maximum Swing Speed - Diesel Version | 4.6 r/min | - | - |
| Swing Ring | Triple-race roller bearing with sealed internal gearing | Triple-race roller bearing with sealed internal gearing | Cross roller bearing with sealed internal gearing |
| Maximum Swing Speed - AC Version | 5 r/min | - | - |
| Maximum Swing Speed | - | 4.9 r/min | 4.9 r/min |
| Parking Brake | - | Wet multiple-disc brake, spring-loaded/hydraulically released | Wet multiple disc brake, spring-loaded/hydraulically released |
| Features (2) | - | All slew ring raceways and grease tub for internal gearing supplied by automatic, central lubrication system | Hydraulic braking of swing motion when control is returned to neutral position or by counteracting control for stronger braking |
| Features (1) | - | Open swing circuit with auto slow down when joysticks in neutral | Closed-loop swing circuit with speed control |
| Features (3) | - | - | All raceways and the internal gearing of swing ring supplied by automatic central lubrication system |
Undercarriage |
|||
| Travel Speed - 1st Stage - Maximum | 0.87 mile/h | 0.68 mile/h | - |
| Travel Speed - 2nd Stage - Maximum | 1.68 mile/h | 1.49 mile/h | - |
| Maximum Tractive Force | 360144 ft·lbf | 265860 lbf | 197157 lbf |
| Gradeability - Travel Drives - Approximate | 47 % | - | - |
| Track Pads - Each Side | 44 | 45 | - |
| Bottom Rollers - Each Side | 7 | 8 | - |
| Support Rollers - Each Side | 2 plus a skid plate in between | 3 | - |
| Travel Drives - Each Side | 1 planetary transmission with 2 two-stage axial piston motors | 1 planetary transmission with 2 two-stage axial piston motors | - |
| Parking Brakes | Wet multiple disc brake, spring loaded/hydraulically released | Wet multiple disc brake, spring loaded/hydraulically released | - |
| Components (1) | All running surfaces of sprockets, idlers, rollers and pad links, as well as teeth contact areas of sprocket and pad links, are hardened | Forged double-grouser track pads | Forged double-grouser track pads |
| Components (2) | Cast double-grouser combined pad-links with bushings connected by hardened full floating pins | Chain links connected by hardened pins and bushings | Chain links connected by hardened pins and bushings |
| Components (3) | Fully hydraulic self-adjusting track tensioning system with membrane accumulator | All running surfaces of sprockets, idlers, rollers and track chain links hardened | Postive Pin Retention (PPR2) sealed and greased track design |
| Components (4) | Automatic hydraulic retarder valve to prevent over-speed on downhill travel | Fully hydraulic self-adjusting track tensioning system with accumulator | All running surfaces of sprockets, idlers, rollers and track chain links hardened |
| Components (5) | Acoustic travel alarm | Automatic hydraulic retarder valve to prevent overspeed on downhill travel | Fully hydraulic self-adjusting track tensioning system with accumulator |
| Components (6) | - | Audible travel alarm | Automatic hydraulic retarder valve to prevent overspeed on downhill travel |
| Gradeability - Travel Drives | - | Approximately 54% | 38°/78% (SAE J1309) |
| Travel Speed - Two Stages - 1st Stage - Maximum | - | - | 1.6 mile/h |
| Travel Speed - Two Stages - 2nd Stage - Maximum | - | - | 2.3 mile/h |
| Maximum Drawbar Pull - Forward | - | - | 192886 lbf |
| Maximum Drawbar Pull - Reverse | - | - | 220987 lbf |
| Hydraulic Track Tensioning | - | - | With accumulator |
| Number of Shoes - Each Side | - | - | 46 |
| Number of Track Rollers - Each Side | - | - | 9 |
| Number of Carrier Rollers - Each Side | - | - | 3 |
| Components (7) | - | - | Audible travel alarm |
Operator's Cab |
|||
| Operator's Eye Level - Approximately | 21.33 ft | - | - |
| Internal Dimensions of Cab - Length | 7.22 ft | 7.32 ft | - |
| Internal Dimensions of Cab - Width | 5.25 ft | 5.33 ft | - |
| Internal Dimensions of Cab - Height | 7.05 ft | 6.79 ft | - |
| Components (1) | Under roof mounted heating ventilating and air conditioning system | Large cab floor window with removable grating for easy cleaning | Pressurized operator station with positive filtration |
| Components (2) | External sun shields at side and rear windows | Pneumatically cushioned and multi-adjustable operator seat with lumbar support, safety belt, head- and armrests | Heated cab mirror |
| Components (3) | Robust instrument panel including large colored BCS screen with transflective technology | Safety switch in operator's seat for automatic motion shutdown | Sliding upper door window (left-hand cab door) |
| Components (4) | Board Control System (BCS) electronic monitoring and data logging system for vital signs and service data of engines, hydraulic system and lubrication system | Joystick integrated in adjustable seat armrest | Glass-breaking safety hammer |
| Components (5) | Hydraulically operated 45 degree access stairway | Full sized trainer seat with safety belt and work table | Removable lower windshield with in cab storage bracket |
| Components (6) | Emergency egress ladder with ladder cage | Auxiliary fold-away seat with safety belt for 3rd person | Joystick Controls Alternate Patterns including ISO/JIS, BHL, MHI, KOBE, or SCM |
| Components (7) | Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat | Operator Protective Guard (rock guard; approved according to ISO 10262:1998 [Top Guard]) compliant | Beverage holder |
| Components (8) | Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, seat heating, safety belt, head- and armrests | Windshield with parallel intermittent wiper/washer | Literature holder |
| Components (9) | Roller blinds at all windows | Roller blinds | AM/FM radio |
| Components (10) | Windshield with parallel intermittent wiper/washer | Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated | Radio with MP3 auxiliary audio port |
| Components (11) | All-round safety glass, armored windshield and sliding side window | Additional emergency ladder in close proximity to emergency escape window | Two stereo speakers |
| Components (12) | Operator Protective Guards (ISO 10262:1998 Level II | - | Storage shelf suitable for lunch or toolbox |
| Components (13) | Joystick controls integrated in independently adjustable seat consoles | - | Color LCD display with warning, filter/fluid change, and working hour information |
| Components (14) | Fold-away auxiliary seat with safety belt | - | Adjustable armrest |
| New BCS Features (1) | - | Robust instrument panel including large (254 mm/10 in) color touch screen | - |
| New BCS Features (3) | - | Graphical data logging | - |
| New BCS Features (4) | - | Fault memory capabilities | - |
| Operator's Eye Level (approximate) | - | 18.04 ft | - |
| New BCS Features (2) | - | On-screen troubleshooting assistance | - |
| New BCS Features (5) | - | USB, Lan (TCP/IP) and CAN BUS interfaces for data export | - |
| New Board Control System (BCS) Features: | - | Electronic monitoring, data logging and diagnostic system for vital signs & service data of engines, hydraulic & lube system | - |
| Components (15) | - | - | Height-adjustable joystick consoles |
| Components (16) | - | - | Neutral lever (lock out) for all controls |
| Components (17) | - | - | Travel control pedals with removable hand levers |
| Components (18) | - | - | Two power outlets, 10 amp (total) |
| Components (19) | - | - | Laminated glass front upper window and tempered other windows |
Automatic Lubrication System |
|||
| Capacity - Grease Container | 119 gal (US) | - | - |
| Type (1) | Dual-circuit system with hydraulically driven heavy-duty pump and electronic time relay control to adjust the pause/lube times | Single-circuit progressive system with hydraulically driven heavy-duty pump and electronic time control | Central bank lubrication system |
| Type (2) | Connected to the lubrication system are the swing roller bearing with internal gearing and all pivot points of attachment, bucket and cylinders | Grease supplied to swing roller bearing, all pivot points of attachment, and swing gearbox bearing | Grease is automatically applied to all attachment pivot points (except bucket linkage) and slew bearing |
| Type (3) | Lubricated pinion for greasing of internal gearing of swing ring | System condition and failures displayed by Board Control System | Standard grease reel on machine for bucket linkage |
| Type (4) | System failures displayed by Board Control System | - | Grease refill service point accessible from ground |
| Type (5) | Grease filters between service station and container as well as directly behind grease pump | - | - |
| Capacity - Grease Barrel | - | 54 gal (US) | 18 gal (US) |
Bucket |
|||
| Bucket Capacity - Face Shovel (heaped 2:1) | 21.6 yd³ | - | - |
| Bucket Capacity - Backhoe (heaped 1:1) | 22.2 yd³ | - | - |
| Standard Bucket Capacity - Backhoe (Heaped 1:1) | - | 15.7 yd³ | - |
Digging Forces |
|||
| Maximum Crowd Force | 291700 ft·lbf | - | - |
| Maximum Tearout Force | 212150 ft·lbf | 146125 lb | - |
| Maximum Breakout Force | - | 164050 lb | - |
Attachments |
|||
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (1) | Automatic roll-back limiter to prevent material spillage and kinematic assistance to hydraulic forces | - | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (2) | Horizontal automatic constant-angle bucket guidance and vertical automatic constant-angle bucket guidance | - | - |
| Shovel attachment with unique TriPower kinematics ensuring the following main features: (3) | Constant boom momentum throughout the whole lift arc and crowd force assistance | - | - |
| All buckets (FS and BH) are equipped with a wear package consisting of: (1) | Special liner material covering main wear areas inside and outside of bucket and lip shrouds between teeth | - | - |
| All buckets (FS and BH) are equipped with a wear package consisting of: (2) | Wing shrouds on side walls and heel shrouds at bottom edges | - | - |
| Type (1) | Catwalks with rails at booms | - | Boom and stick torsion-resistant with welded box design |
| Type (2) | Special wear packages for highly abrasive materials on request | - | High-tensile steel with solid steel castings at pivot areas |
| Type (3) | Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve | - | Boom and stick stress-relieved after welding |
| Type (4) | Welding procedures allow for internal counter-welding (double prep weld) wherever possible | - | Float valve for boom down function |
| Type (5) | Booms and sticks are stress-relieved after welding | - | - |
| Type (6) | Booms and sticks are torsion-resistant, welded box design of high-tensile steel with solid steel castings at pivot areas | - | - |
| Buckets Equipped With | - | - | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
Attachment |
|||
| Type (5) | - | Float valve for boom down function | - |
| Type (2) | - | High-tensile steel with solid steel castings at pivot areas | - |
| Type (3) | - | Boom and stick stress-relieved after welding | - |
| Type (1) | - | Boom and stick torsion-resistant with welded box design | - |
| Type (4) | - | Catwalks with rails at boom | - |
| Buckets Equipped With | - | – Special liner material covering main wear areas inside and outside – Lip shrouds – Wing shrouds – Heel shrouds |
- |
Operating Weights - Backhoe |
|||
| Standard Track Pads | - | 2.62 ft | - |
| Operating Weight | - | 507500 lb | 154 ton (US) |
| Ground Pressure | - | 31.9 psi | - |
Hydraulic System with Electronic Pump Management |
|||
| Maximum Swing Oil Flow | - | 216 gal/min | - |
| Maximum Pressure - Attachment | - | 4495 psi | - |
| Filters (4) | - | Pressure filters (6 μm) for servo circuit | - |
| Electronic Pump Management Contains (3) | - | Automatic return of main pumps to zero flow | - |
| Features (2) | - | Cooling of pump transmission gear oil | - |
| Maximum Pressure - Travel | - | 4495 psi | - |
| Maximum Pressure - Swing - Acceleration | - | 4495 psi | - |
| Filters (3) | - | Full-flow filters (10 μm) for cooling return circuit | - |
| Electronic Pump Management Contains (2) | - | Dedicated circuit pump allocation | - |
| Maximum Total Oil Flow | - | 621 gal/min | - |
| Filters (2) | - | Full-flow filters (10 μm) for complete return circuit | - |
| Main Pumps | - | 6 × variable swash plate pumps | - |
| Filters (1) | - | Full-flow high-pressure filters (100 μm) for main pumps, installed directly behind each pump | - |
| Electronic Pump Management Contains (4) | - | Automatic rpm reduction of engine speed during working breaks | - |
| Filters (5) | - | Transmission oil filter (40 μm) | - |
| Electronic Pump Management Contains (5) | - | Reduced oil flow of main pumps at high hydraulic oil temperature and at high engine temperature | - |
| Electronic Pump Management Contains (1) | - | Electronic load limit control | - |
| Features (1) | - | Pressure cut-off function for all main pumps | - |
| Total Volume of Hydraulic Oil | - | 925 gal (US) | - |
| Hydraulic Tank Capacity | - | 740 gal (US) | - |
| Maximum Pressure - Swing - Deceleration | - | 5080 psi | - |
Centralized Service Area |
|||
| Equipped With (3) | - | Indicator light for hydraulic tank full | - |
| Equipped With (1) | - | Quick couplings for: – Diesel fuel – Engine coolant – Pump transmission gear oil – Engine oil (oil pan) – Hydraulic oil |
Emergency stop |
| Features | - | Centralized service area accessible from ground level. | - |
| Equipped With (2) | - | Cat jump-start socket | Quick couplings for: Diesel fuel and Grease |
| Feature | - | - | Accessible from ground level |
Working Ranges |
|||
| Maximum Digging Reach | - | 52.17 ft | - |
| Maximum Digging Depth | - | 26.57 ft | - |
| Maximum Digging Height | - | 45.6 ft | - |
Operating Specifications |
|||
| Operating Weight | - | 254 ton (US) | - |
| Bucket Payload | - | 24 Sh Ton | - |
Engine - Equivalent to U.S. EPA Tier 2 |
|||
| Gross Power - SAE J1995 | - | 1040 HP | 839 HP |
| Engine Model | - | Cat C32 ACERT | Cat® C27 |
| Net Power - SAE J1349 | - | 1032 HP | 746 HP |
Diesel Engine - Tier 4 Final |
|||
| Components (1) | - | Cat NOx reduction system | - |
| Components (7) | - | Two-stage fuel filter | - |
| Components (3) | - | MEUI™-C fuel system | - |
| Alternator | - | 275A | - |
| Bore | - | 5.71 in | - |
| Components (4) | - | Hydraulically driven radiator fan with variable electronically controlled fan speed | - |
| No. of Cylinders | - | 12 | - |
| Displacement | - | 1959 in³ | - |
| Fuel Tank Capacity | - | 951 gal (US) | - |
| Components (5) | - | Micro processed engine management | - |
| Rated Speed | - | 1,800 min-1 (1,800 rpm) | - |
| Aspiration | - | Turbocharged and air-to-air aftercooled | - |
| Components (2) | - | Dual Diesel Oxidation Catalysts (DOCs) | - |
| Components (8) | - | Additional high-capacity water separator including electric priming pump | - |
| Components (9) | - | Large fuel tank allows for 24 hour machine operation | - |
| Components (6) | - | Heavy-duty air filters | - |
| Maximum Altitude without Deration | - | 2925 m (9,600 ft) – above sea level (a.s.l.) | - |
| Stroke | - | 6.38 in | - |
| Make and Model | - | Cat C32 ACERT | - |
Diesel Engine - Equivalent to Tier 2 |
|||
| Components (3) | - | Heavy-duty air filters | - |
| Components (4) | - | Two-stage fuel filter | - |
| Fuel Tank Capacity | - | 951 gal (US) | - |
| No. of Cylinders | - | 12 | - |
| Components (2) | - | Micro processed engine management | - |
| Displacement | - | 1959 in³ | - |
| Maximum Altitude without Deration | - | 3622 m (11,884 ft) – above sea level (a.s.l.) | - |
| Bore | - | 5.71 in | - |
| Components (1) | - | Hydraulically driven radiator fan with variable electronically controlled fan speed | - |
| Stroke | - | 6.38 in | - |
| Aspiration | - | Turbocharged and air-to-air aftercooled | - |
| Components (5) | - | Additional high-capacity water separator including electric priming pump | - |
| Rated Speed | - | 1800 min-1 (1,800 rpm) | - |
| Alternator | - | 275A | - |
| Make and Model | - | Cat C32 ACERT | - |
| Components (6) | - | Large fuel tank allows for 24 hour machine operation | - |
Engine - U.S. EPA Tier 4 Final |
|||
| Net Power - SAE J1349 | - | 1019 HP | 746 HP |
| Gross Power - SAE J1995 | - | 1033 HP | 824 HP |
| Engine Model | - | Cat® C32 ACERT™ | Cat® C27 |
Engine - Cat C27 with Tier 4 Final Emission Standards |
|||
| Number of Cylinders | - | - | 12 |
| Bore | - | - | 5.4 in |
| Stroke | - | - | 6 in |
| Displacement | - | - | 1648 in³ |
Engine - Cat C27 with Tier 1 or Tier 2 Equivalent Emission Standards |
|||
| Number of Cylinders | - | - | 12 |
| Bore | - | - | 5.4 in |
| Stroke | - | - | 6 in |
| Displacement | - | - | 1648 in³ |
| Aspiration | - | - | Turbocharged and air-to-air aftercooled |
Weights |
|||
| Ground Pressure | - | - | 23.6 psi |
| Note | - | - | Operating weight includes: 700 mm (28 in) track shoes, 7.6 m (24 ft 11 in) boom, 3.4 m (11 ft 2 in) stick, standard rock bucket, 100% fuel and lubricants |
| Operating Weight | - | - | 308000 lb |
Track |
|||
| Standard | - | - | 28 in |
| Wide | - | - | 36 in |
| Extra Wide | - | - | 39 in |
| Number of Shoes - Each Side | - | - | 46 |
| Number of Track Rollers - Each Side | - | - | 9 |
| Number of Carrier Rollers - Each Side | - | - | 3 |
| Track Pads | - | - | Double grouser |
Drive |
|||
| Travel Speed - Two Stages - 1st Stage - Maximum | - | - | 1.4 mile/h |
| Travel Speed - Two Stages - 2nd Stage - Maximum | - | - | 2.1 mile/h |
| Maximum Drawbar Pull - Forward | - | - | 192886 lbf |
| Maximum Drawbar Pull - Reverse | - | - | 220987 lbf |
| Gradeability - Travel Drives | - | - | Approximately 42% |
| Hydraulic Track Tensioning | - | - | With accumulator |
| Maximum Drawbar Pull | - | - | 179847 lbf |
Service Refill Capacities |
|||
| Fuel Tank | - | - | 449 gal (US) |
| Cooling System | - | - | 44 gal (US) |
| Engine Oil | - | - | 23 gal (US) |
| Swing Drive | - | - | 2.4 gal (US) |
| Hydraulic System - Including Tank | - | - | 463 gal (US) |
| Hydraulic Tank | - | - | 253 gal (US) |
| Grease Tank | - | - | 18 gal (US) |
Hydraulic System |
|||
| Main Pumps | - | - | 3 × variable swash plate pumps |
| Main Pumps - Maximum Total Oil Flow | - | - | 407 gal/min |
| Main Pumps - Maximum Pressure - Attachment | - | - | 4641 psi |
| Pilot Pump | - | - | 1 × gear pump |
| Pilot Pump - Maximum Flow, Pilot | - | - | 40.4 gal/min |
| Pilot Pump - Maximum Pressure, Pilot | - | - | 1378 psi |
| Main Pumps - Maximum Pressure - Travel | - | - | 4641 psi |
| Swing Pump | - | - | 1 × variable swash plate pump |
| Engine Fan Pump - Maximum Flow, Engine Fan | - | - | 53.1 gal/min |
| Engine Fan Pump - Maximum Pressure, Engine Fan | - | - | 3191 psi |
| Engine Fan Pump | - | - | 1 × variable swash plate pump |
| Hydraulic Fan Pump - Maximum Flow, Hydraulic Fan | - | - | 22.7 gal/min |
| Swing Pump - Maximum Flow - Swing | - | - | 127 gal/min |
| Hydraulic Fan Pump | - | - | 1 × variable swash plate pump |
| Hydraulic Fan Pump - Maximum Pressure, Hydraulic Fan | - | - | 1958 psi |
| Swing Pump - Maximum Pressure - Swing | - | - | 5294 psi |
| Hydraulic Oil Cooling - Maximum Flow | - | - | 284 gal/min |
| Hydraulic Oil Cooling - Diameter of Fan | - | - | 40 in |
| Filters (1) | - | - | Full-flow high-pressure filters (200 μm) for main pumps |
| Filters (2) | - | - | Full-flow filters (20 μm) for complete return circuit |
| Filters (3) | - | - | Pressure filters (16 μm) for servo circuit |
| Filters (4) | - | - | Full-flow filters (6 μm) for engine cooling return circuit |
| Filters (5) | - | - | Swing charge filter (15 μm) |
| Filters (6) | - | - | Pump case return screens (125 μm) |
Engine |
|||
| Emissions | - | - | U.S. EPA Tier 4 Final and EU Stage V; China Nonroad Stage III, equivalent to U.S. EPA Tier 2; Equivalent to U.S. EPA Tier 1 |
Backhoe Attachment (BH) - Working Range |
|||
| Maximum Digging Depth | - | - | 26.3 ft |
| Maximum Digging Reach | - | - | 45.6 ft |
| Maximum Digging Height | - | - | 41.9 ft |
| Maximum Dump Height | - | - | 27.9 ft |
Backhoe Attachment (BH) - Digging Forces |
|||
| Bucket Digging Force - ISO | - | - | 120947 lbf |
| Bucket Digging Force - SAE | - | - | 112600 lbf |
| Stick Digging Force - ISO | - | - | 104761 lbf |
| Stick Digging Force - SAE | - | - | 98800 lbf |
Backhoe Attachment (BH) - Backhoe |
|||
| Capacity 1:1 | - | - | 10.6 yd³ |
| Total Width | - | - | 8.8 ft |
| Number of Teeth | - | - | 5 |
| Tooth System | - | - | Cat C70 or M75 |
| Weight - Including Standard Wear Package | - | - | 18521 lb |
| Maximum Material Density - Loose | - | - | 3030 lb/yd³ |
