No derating required up to 4267 m (14,000 ft) altitude.
-
-
Weights
Operating Weight
110225 lb
154888 lb
-
Shipping Weight
84373 lb
111739 lb
-
Note (1)
D9 Operation Weight includes hydraulic controls, blade tilt cylinder, coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU Blade, Single-Shank Ripper, 610 mm (24 in) ES shoes and operator.
D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.
-
Note (2)
D9 Operation Weight includes base machine chassis with cab, pivot shaft, roller frames, track and ROPS.
D10 Shipping Weight includes coolant, lubricants, 10% fuel, FOPS cab, fast fuel, and 610 mm (24 in) ES shoes.
-
Undercarriage
Shoe Type
Extreme Service
Extreme Service (ES)
-
Width - Shoe
24 in
24 in
-
Shoes/Side
43
44
-
Grouser Height
3.3 in
3.7 in
-
Pitch
9.4 in
10.2 in
-
Ground Clearance
18.1 in
28.5 in
-
Track Gauge
88.6 in
100.4 in
-
Length - Track on Ground
136.6 in
152.8 in
-
Ground Contact Area
45.6 ft²
7347 in²
-
Track Rollers/Side
8
8
-
Number of Carrier Rollers
1 per side (optional)
1 per side (optional)
-
Standards
ROPS
Rollover Protective Structure (ROPS) meets the following criteria ISO 3471:2008.
Rollover Protective Structure (ROPS) meets the following criteria: ISO 3471:2008.
-
FOPS
Falling Object Protective Structure (FOPS) meets the following criteria ISO 3449:2005 LEVEL II.
Falling Object Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 LEVEL II.
-
Sound
The average dynamic spectator sound power level when ISO 6395:2008 is used to measure the value for a machine is 116 dB(A). The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling
Operator Sound Pressure Level (ISO 6396:2008): 78 db(A)
-
Sound (1)
The average dynamic operator sound pressure level when ISO 6396:2008 is used to measure the value for an enclosed cab is 78 dB(A). The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine c
Exterior Sound Pressure Level (ISO 6395:2008): 116 db(A)
-
Sound (2)
Hearing protection may be needed when the machine is operated with an open operator station for extended periods, in a noisy environment, or with a cab that is not properly maintained.
-
-
Note
-
The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine cooling fan speeds. The measurement was conducted with the cab doors and the cab windows closed. The cab was properly installed and
-
Note (1)
-
The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engine
cooling fan speeds.
-
Note (2)
-
The sound levels listed above include both measurement uncertainty and uncertainty due to production variation.
-
Note (3)
-
The available sound suppression package can reduce the dynamic exterior sound power level of the machine by up to 4 db(A) and the dynamic operator sound pressure level by up to 2 db(A).
Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
-
Note (4)
-
Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
-
Note (5)
-
**Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.
-
FLUID CAPACITIES
Fuel Tank (Splash Fill)
254 gal (US)
-
-
DEF Tank (Tier 4 only)
9.5 gal (US)
-
-
Fuel Tank (Fast Fill)
248 gal (US)
-
-
Cooling System
21 gal (US)
-
-
Engine Crankcase*
10 gal (US)
-
-
Powertrain
40 gal (US)
-
-
Final Drives (each)
4 gal (US)
12.2 gal (US)
-
Roller Frames (each)
12 gal (US)
-
-
Pivot Shaft Oil
8 gal (US)
9.5 gal (US)
-
Hydraulic System Tank
24 gal (US)
32.2 gal (US)
-
Note
*With oil filters.
-
-
Note 2
Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD. B20 should meet ASTM D7467 specification (biodiesel blend stock should meet Cat biodiesel spec, ASTM D6751 or EN 14214). Cat DEO-ULSTM or
-
-
Note 3
All non-road Tier 4 Final diesel engines are required to use only ultra-low sulfur diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less.
-
-
Note 4
Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241.
-
-
Cooling System Refill – Tier 4 Final Engine
-
46.2 gal (US)
-
Engine Crankcase Sump
-
27.2 gal (US)
-
Power Train - Total Volume
-
81.4 gal (US)
-
Power Train - Refill Volume
-
74.8 gal (US)
-
Track Roller Frames (each)
-
16.9 gal (US)
-
Hydraulic Controls
Pump Type
Piston-type geared to flywheel
Variable displacement piston
-
Pump Output - Steering
96 gal/min
-
-
Fan Pump
21 gal/min
21.7 gal/min
-
Tilt Cylinder Flow - Rod End Flow
53 gal/min
112 gal/min
-
Tilt Cylinder Flow - Head End Flow
53 gal/min
63.4 gal/min
-
Lift Cylinder Relief Valve Setting
3800 lbf/in
4061.1 psi
-
Tilt Cylinder Relief Valve Setting
2799 psi
3872.5 psi
-
Ripper - Lift - Relief Valve Setting
3800 psi
4061.1 psi
-
Ripper - Pitch - Relief Valve Setting
3800 psi
4061.1 psi
-
Steering System - Pressure
5874 psi
-
-
Tank Capacity
24 gal/min
32.2 gal (US)
-
Note (1)
Steering pump output measured at 1,750 engine rpm and 30 000 kPa (4,350 psi).
Implement Pump output measured are 2,010 engine rpm and
7000 kPa (1,015 psi).
-
Note (2)
Implement pump output measured at 1,750 engine rpm and 20 000 kPa (2,900 psi).
Fan Pump output measured at 2,010 engine rpm and 26 000 kPa (3,771 psi).
-
Note (3)
Fan pump output measured at 1,750 engine rpm and 17 000 kPa (2,470 psi)
Electro-hydraulic pilot valves assist operations of ripper and dozer controls.
-
Pump Output - Implement
-
112 gal/min
-
Cylinder Sizing - Blade Lift - Bore
-
5.5 in
-
Cylinder Sizing - Blade Tilt - Bore
-
8.3 in
-
Cylinder Sizing - Ripper Shank Lift - Bore
-
8.3 in
-
Cylinder Sizing - Ripper Shank Angle - Bore
-
7.1 in
-
Cylinder Sizing - Blade Lift - Stroke
-
65.1 in
-
Cylinder Sizing - Blade Tilt - Stroke
-
9.5 in
-
Cylinder Sizing - Ripper Shank Lift - Stroke
-
21.1 in
-
Cylinder Sizing - Ripper Shank Angle - Stroke
-
26 in
-
Air Conditioning System
Air Conditioning
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430) the system contains 2.1 kg of refrigerant which has a CO2 equivalent of 3.003 metric tonnes.
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.600 metric tonnes.
-
Transmission
1.0 Forward
2.2 mile/h
2.5 mile/h
-
2.0 Forward
3.9 mile/h
4.5 mile/h
-
3.0 Forward
6.8 mile/h
7.8 mile/h
-
1.0 Reverse
2.7 mile/h
3.2 mile/h
-
2.0 Reverse
4.8 mile/h
5.6 mile/h
-
3.0 Reverse
8.4 mile/h
9.8 mile/h
-
Type
Planetary powershift
Planetary powershift
-
1.5 Forward
-
3.4 mile/h
-
2.5 Forward
-
6 mile/h
-
1.5 Reverse
-
4.2 mile/h
-
2.5 Reverse
-
7.5 mile/h
-
Transmission Clutch Diameter
-
17 in
-
Blade - Semi-Universal
Blade Capacity (SAE J1265)
17.8 yd³
-
-
Blade Width (over end bits)
171.3 in
-
-
Blade Height
76.1 in
-
-
Maximum Digging Depth
23.9 in
-
-
Ground Clearance at Full Lift
56 in
-
-
Maximum Tilt
37 in
-
-
Blade Weight
10587 lb
-
-
Total Operating Weight* (with blade and single-shank ripper)
110205 lb
-
-
Note
* Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
-
Blade - Universal
Blade Capacity (SAE J1265)
21.7 yd³
-
-
Blade Width (over end bits)
184.3 in
-
-
Blade Height
76.1 in
-
-
Maximum Digging Depth
23.9 in
-
-
Ground Clearance at Full Lift
56 in
-
-
Maximum Tilt
39.9 in
-
-
Blade Weight
12016 lb
-
-
Total Operating Weight* (with blade and single-shank ripper)
111362 lb
-
-
Note
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
-
Ripper - Single Shank
Maximum penetration force * (shank vertical)
35520 lbf
49233 lbf
-
Maximum penetration depth (standard tip)
48.5 in
59.2 in
-
Pryout Force
74637 lbf
-
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
34.7 in
36 in
-
Number of Pockets
1
-
-
Weight
10701 lb
14209 lb
-
Total Operating Weight* (with SU Blade and noted ripper)
110205 lb
-
-
Note
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes
and the noted blade and ripper type.
Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.
-
Ripper - Single Shank, Deep Ripping
Maximum penetration force * (shank vertical)
38667 lbf
53055 lbf
-
Maximum penetration depth (standard tip)
68 in
78.3 in
-
Pryout Force
74412 lbf
-
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
32.2 in
-
-
Number of Pockets
1
-
-
Weight
10981 lb
14548 lb
-
Total Operating Weight* (with SU Blade and noted ripper)
110485 lb
-
-
Note
*Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
Weight includes one shank. Add 544 kg (1,199 lb) for each additional shank.
-
Ripper - Multi-Shank, Adjustable Parallelogram
Maximum Penetration Force - Shank Vertical
34621 lbf
-
-
Maximum Penetration - Standard Tip
31.4 in
-
-
Pry-Out Force - Multi-Shank Ripper with One Tooth
81156 lbf
-
-
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole
34.6 in
-
-
Number of Pockets
3
-
-
Weight
12136 lb
-
-
Total Operating Weight* - With SU-Blade and Ripper
111739 lb
-
-
Note
* Total Operating Weight includes: single tilt hydraulics, coolant, lubricants, full fuel tank, ROPS, FOPS cab, 610 mm (24 in) ES track shoes and the noted blade and ripper type.
-
-
Dimensions (Approximate)
Ground Clearance*
18.1 in
28.5 in
-
Track Gauge
88.6 in
100.4 in
-
Width - Without Trunnions - Standard Shoe
113 in
-
-
Width - Over Trunnions
130.3 in
148 in
-
Height - FOPS Cab*
150.4 in
162.8 in
-
Height - Top of Stack*
152.6 in
171.5 in
-
Height - ROPS/Canopy*
157.5 in
173.5 in
-
Drawbar Height (Center of Clevis)*
30 in
-
-
Length - Track on Ground
136.6 in
152.8 in
-
Overall Length - Basic Tractor
193.3 in
209.6 in
-
Length - Basic Tractor - With Drawbar
206.4 in
-
-
Length - Basic Tractor - With Winch
218.3 in
-
-
Length - With SU-Blade**
259.9 in
-
-
Length - With U-Blade
274.3 in
305.1 in
-
Length - With Single-Shank Ripper
257 in
278.8 in
-
Length - With Multi-Shank Ripper
257.4 in
285.1 in
-
Overall Length - SU-Blade/SS Ripper
323.6 in
360.6 in
-
Note (1)
*Includes grouser height for total dimensions on hard surfaces.
*Includes grouser height for total dimensions on hard surfaces.
-
Width - Without Trunnions - 610 mm/24 in ES
-
130.4 in
-
Length - With SU-Blade
-
292 in
-
Winches
Winch Model
PA 140VS
-
-
Weight*
3950 lb
-
-
Oil Capacity
4 gal (US)
-
-
Drum Width
12.6 in
-
-
Wire Cable Diameter - Recommended
1.13 in
-
-
Wire Cable Diameter - Optional
1.25 ft
-
-
Maximum Drum Capacity - Recommended Cable Length
257 in
-
-
Maximum Drum Capacity - Optional Cable Length
204 ft
-
-
Wire Cable Ferrule Size - Outside Diameter
2.4 in
-
-
Wire Cable Ferrule Size - Length
2.8 in
-
-
Note
*Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope. With counterweight: 3700 kg (8,150 lb).
10SU ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry)
-
19.98 in
-
10SU ABR - Digging Depth - Blade Pitch: Nominal
-
25.23 in
-
10SU ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread)
-
30.08 in³
-
10SU ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry)
-
66.14 in
-
10SU ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread)
-
53.86 in
-
10SU ABR - Ground Clearance - Maximum Tilt LH
-
56.3 in
-
10SU ABR - Ground Clearance - Maximum Tilt RH
-
56.3 in
-
10U ABR - Capacity (SAE J1265)
-
28.7 yd³
-
10U ABR - Width (over end bits)
-
207.1 in
-
10U ABR - Height
-
83.5 in
-
10U ABR - Digging Depth - Blade Pitch: Full Racked Back (Carry)
-
19.98 in
-
10U ABR - Digging Depth - Blade Pitch: Nominal
-
60 in
-
10U ABR - Digging Depth - Blade Pitch: Full Pitched Forward (Spread)
-
30.1 in
-
10U ABR - Ground Clearance - Blade Pitch: Full Racked Back (Carry)
-
66.1 in
-
10U ABR - Ground Clearance - Blade Pitch: Full Pitched Forward (Spread)
-
53.9 in
-
10U ABR - Ground Clearance - Maximum Tilt LH
-
60.8 in
-
10U ABR - Ground Clearance - Maximum Tilt RH
-
60.8 in
-
10U ABR - Weights - Blade Weight*
-
23585 lb
-
10U ABR - Weights - Total Operating Weight** (with blade and SS ripper)
-
154888 lb
-
Note (1)
-
Maximum LH and RH tilt for 10SU ABR and 10U ABR blades: 17.31 degrees
-
Note (2)
-
*Does not include hydraulic controls but includes blade cylinders, pusharms.
-
Note (3)
-
**D10 Operating Weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer, dual tilt, single-shank ripper with pin-puller, fast fuel, 610 mm (24 in) ES shoes, and operator.
-
Engine - U.S. EPA Tier 2 Equivalent
Engine Model
-
Cat® C27
-
Engine Power - Net SAE J1349/ISO 9249** - Forward
-
603 HP
-
Engine Power - Net SAE J1349/ISO 9249** - Reverse
-
722 HP
-
Engine Power - Gross SAE J1995* - Forward
-
631 HP
-
Engine Power - Gross SAE J1995* - Reverse
-
766 HP
-
Engine Power - ISO 14396* - Forward
-
622 HP
-
Engine Power - ISO 14396* - Reverse
-
756 HP
-
Displacement
-
1648 in³
-
Bore
-
5.4 in
-
Stroke
-
6 in
-
Emissions
-
U.S. EPA Tier 2 Equivalent
-
Note (1)
-
*Excludes all fan losses.
-
Note (2)
-
All Engine ratings apply at 1,800 rpm.
-
Note (3)
-
Tier 2 equivalent rating (in FWD gears) begins altitude de-rate at 4480 m (14,700 ft).
-
Note (4)
-
Tier 4/EU Stage 5 equivalent rating (in FWD gears) begins altitude de-rate at 4420 m (14,500 ft).
-
Note (5)
-
**Net power advertised is the power available at the flywheel when the engine is equipped with air cleaner, muffler, alternator, fan, and engine emissions controls as required at 25° C ambient temperature.
