Cat® C13 Diesel Engine
Product description
The Cat® C13 Industrial Diesel Engine is offered in ratings ranging from 287-388 bkW (385-520 bhp) @ 1800-2100 rpm. Industries and applications powered by engines include: Agriculture, Ag Tractors, Aircraft Ground Support, Bore/Drill Rigs, Chippers/Grinders, Combines/Harvesters, Compactors/Rollers, Compressors, Construction, Cranes, Crushers, Dredgers, Forestry, General Industrial, Hydraulic Power Units, Irrigation Equipment, Loaders/Forwarders, Material Handling, Mining, Mobile Earthmoving Equipment, Paving Equipment, Pumps, Shovels/Draglines, Specialty Ag Equipment, Surface Hauling Equipment, Trenchers and Underground Mining Equipment.
Power Rating
- Maximum Power - 520HP
- Maximum Torque - 1756lb-ft @ 1400 rpm
- Rated Speed - 1800-2100 rpm
- Minimum Power - 385HP
Emission Standards
- Emissions - U.S. EPA Tier 4 Final
General
- Engine Configuration - In-Line 6
- Bore - 5.1in
- Stroke - 6.2in
- Displacement - 762.8in³
- Compression Ratio - 17.0:1
- Aspiration - Turbocharged-Aftercooled (TA)
- Combustion System - Direct Injection
- Rotation from Flywheel End - Counterclockwise
- Aftertreatment - DOC+DPF+SCR
Engine Dimensions - Approximate
- Length - 50in
- Width - 39in
- Height - 45in
- Weight - Net Dry - Basic Operating Engine Without Optional Attachments - 2520lb
Aftertreatment Dimensions
- Length - 42in
- Width - 41in
- Height - 26in
- Weight - 571lb
PETU Dimensions - Tier 4 Final Only
- Length - 33.6in
- Width - 11.3in
- Height - 21.7in
- Weight - 42.8lb
- Volume Capacity - 51.1qt (US)
Standard Equipment:
-
- Air Inlet System
-
- Turbocharged
- Air-to-Air Aftercooled
- Mid-mount turbocharged system with front and rear exhaust configurations (Tier 4 Final, Stage IV)
-
- Control System
-
- Electronic control system
- Over-foam wiring harness
- Automatic altitude compensation
- Power compensated for fuel temperature
- Configurable software features
- Engine monitoring system SAE J1939 broadcast and control
- Integrated Electronic Control Unit (ECU)
- Remote fan control
-
- Cooling System
-
- Vertical or RH thermostat outlet
- Centrifugal water pump
- Guidance on cooling system design available through your dealer to ensure equipment reliability
-
- Flywheels And Flywheel Housing
-
- SAE No. 1 flywheel housing
- Available SAE No. 1 power take off with optional SAE A, SAE B or SAE C power take off drives. Engine power can also be taken from the front of the engine with optional attachments. (Tier 4 Final, Stage IV).
-
- Fuel System
-
- MEUI injection
- Primary fuel filter
- Secondary fuel filters
- Fuel transfer pump
- Electronic fuel priming
-
- Lube System
-
- Open crankcase ventilation system
- Oil cooler
- Oil filler
- Lube oil filter
- Oil dipstick
- Gear driven oil pump
- Choice of front, rear or center sumps
- Open crankcase ventilation system with fumes disposal (optional OCV filter system) (Tier 4 Final, Stage IV)
-
- Power Take Off (pto)
-
- SAE A, SAE B or SAE C power take off (PTO) drives. Engine power can also be taken from the front of the engine on some applications.
-
- General
-
- Paint: Caterpillar yellow, with optional colors available at request
-
- U.s. Epa Tier 4 Interim, Eu Stage Iiib Aftertreatment / Clean Emissions Control Equipment
-
- Cat Regeneration System
- Clean Emissions Module (CEM), consisting of Diesel Particulate Filter (DPF) and Diesel Oxidation Catalyst (DOC)
- NOx Reduction System (NRS)
- Flex pipe connection kit with 90° rotatable elbows to attach to Cat Regeneration System Inlet
- Available in 12 volt or 24 volt systems
-
- U.s. Epa Tier 4 Final, Eu Stage Iv Aftertreatment
-
- Cat Regeneration System
- Clean Emissions Module (CEM), consisting of Diesel Particulate Filter (DPF) and Diesel Oxidation Catalyst (DOC)
- Aftertreatment Electronic Control Unit (ECU)
- NOx Reduction System (NRS)
- Pump Electronic Control Unit (PETU)
- Selective Catalytic Reduction (SCR)
- Available in 12V or 24V systems
